Flaps during transit A320
Thread Starter
Join Date: Dec 2008
Location: Birmingham
Age: 39
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
Flaps during transit A320
Hi folks,
We do 97% of the takeoffs with flaps 1+f. So why don't we retract the flaps after landing to that position and leave it there. Would save one cycle. Saw this recently with Iraq airways and their a321 during transit.
Any hints in that?
Thanks
We do 97% of the takeoffs with flaps 1+f. So why don't we retract the flaps after landing to that position and leave it there. Would save one cycle. Saw this recently with Iraq airways and their a321 during transit.
Any hints in that?
Thanks
It used to be the case that flaps were left at 1+F when ground air temperature was 30 degrees centigrade or more, to avoid a mis-triggering of a wing air leak caution. The caution is surpressed when the flaps/slats are out. Our company still does this, but I've just checked the FCOM which says that wing air bleed leak does not trigger until 124 degrees, so maybe Airbus have changed the parameters?
The F part of 1+F - i.e. the flaps - hang quite low, which is a potential damage hazard to ground servicing vehicles - particularly fuel trucks - who are probably not expecting it, so leaving flaps out on the ramp is not an ideal situation.
Leaving flaps out at a particular setting is a safety hazard for mis-setting take off config too. Many incidents have been documented of crews setting the wrong take off config, because some crews insist on saying things like config 1+F is "standard" which is a recipe for mistakes.
The F part of 1+F - i.e. the flaps - hang quite low, which is a potential damage hazard to ground servicing vehicles - particularly fuel trucks - who are probably not expecting it, so leaving flaps out on the ramp is not an ideal situation.
Leaving flaps out at a particular setting is a safety hazard for mis-setting take off config too. Many incidents have been documented of crews setting the wrong take off config, because some crews insist on saying things like config 1+F is "standard" which is a recipe for mistakes.
Last edited by Uplinker; 25th May 2015 at 11:03. Reason: You guys beat me to it, since I was checking the FCOM !
Join Date: Jun 2007
Location: Wanderlust
Posts: 3,407
Likes: 0
Received 0 Likes
on
0 Posts
Uplinker
The parameters are not changed and although wing leak is triggered above 124degrees the after landing procedure remains same i.e. above 30 degrees for keeping flap1 is not changed. Since it is triggered from slat, after shut down it is possible to retract the flap with yellow electrics though strictly speaking it is not SOP.
The parameters are not changed and although wing leak is triggered above 124degrees the after landing procedure remains same i.e. above 30 degrees for keeping flap1 is not changed. Since it is triggered from slat, after shut down it is possible to retract the flap with yellow electrics though strictly speaking it is not SOP.
......... it is possible to retract the flap with yellow electrics though strictly speaking it is not SOP.
I think it only applies to the early A320s not the newer ones. It's quite common to see this at Middle Eastern airports for obvious reasons.
If you use the yellow electric pump or blue pump override, remember to switch them off afterwards as you will get problems with spoilers and various ECAM messages if you leave them on.
If you use the yellow electric pump or blue pump override, remember to switch them off afterwards as you will get problems with spoilers and various ECAM messages if you leave them on.
The other option is to turn engine bleeds off - disarms the sensors. Great for quick get away once overheat warning triggered. Just leave bleeds off till after takeoff.
I had it in Erbil once, with flaps one! Only other option than waiting for 53deg OAT to subside. No thanks!
I had it in Erbil once, with flaps one! Only other option than waiting for 53deg OAT to subside. No thanks!
Only half a speed-brake
FCOM wording [valid for MSNs 04xx 09xx 17xx 29xx 42xx 44xx]
FLAPS....................................................... ......................... RETRACT
Set the FLAPS lever to position 0.
FLAPS....................................................... ......................... RETRACT
Set the FLAPS lever to position 0.
- If the approach was made in icing conditions, or if the runway was contaminated with slush or snow, do not retract the flaps and slats until after engine shutdown and after the ground crew has confirmed that flaps and slats are clear of obstructing ice.
- On ground, hot weather conditions may cause overheating to be detected around the bleed ducts in the wings, resulting in “AIR L (R) WING LEAK” warnings. Such warnings may be avoided during transit by keeping the slats in Configuration 1 when the OAT is above 30 °C.
- To avoid damage on the RTLU (Rudder Travel Limit Unit) mechanical stop, the SLATS/FLAPS should be retracted before all ADIRS are set to OFF simultaneously.
Didn't know that about the RTLU FLightdetent - thanks!
Goeasy, interesting tip, but might not there be engine handling issues if the engine bleeds are off for takeoff, e.g. increased compressor stall risk etc?
Goeasy, interesting tip, but might not there be engine handling issues if the engine bleeds are off for takeoff, e.g. increased compressor stall risk etc?
Join Date: Apr 2009
Location: Left Seat
Age: 40
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
Here in India, we almost always have temperatures > 30C on the ramp, sometimes as high as the late 40s. Our company SOP doesn't ask us to keep CONF1 on the ground, nor have I personally ever encountered the AIR WING LEAK fault.
Join Date: Jun 2007
Location: Wanderlust
Posts: 3,407
Likes: 0
Received 0 Likes
on
0 Posts
I don't think there are any updated sensors as the 30C recommendation is applicable to all aircraft. Perhaps the company may be preferring occasional wing bleed warning by retracting flaps to the possibility of damage to the RTLU by leaving them at 1+F.
Join Date: Jan 2010
Location: Eagles Nest
Posts: 485
Likes: 0
Received 0 Likes
on
0 Posts
Operator I worked for did it to save cycles ( not Airbus or Boeing ) . They got told by manufacture that the flap tracks where never designed to have flaps out for extended periods , especially high winds , towing . So they reverted back to retracting them after every flight .
Join Date: Jan 2008
Location: Scandinavia
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
If you get out of the habit of setting flaps before take off what happens the next time you need something different to 1+f....
Spanair Flight 5022 - Wikipedia, the free encyclopedia
Join Date: May 2000
Location: Glorious West Sussex
Age: 76
Posts: 1,020
Likes: 0
Received 0 Likes
on
0 Posts
Stone Cold
One understands the system quite well, thank you. How well do you understand the hydraulic system and it's relationship with slats and flaps? Think about it....
One understands the system quite well, thank you. How well do you understand the hydraulic system and it's relationship with slats and flaps? Think about it....