Go Back  PPRuNe Forums > Aircrew Forums > Rotorheads
Reload this Page >

Helicopter Rotor Blade Radar (RODAR)

Rotorheads A haven for helicopter professionals to discuss the things that affect them

Helicopter Rotor Blade Radar (RODAR)

Old 13th May 2015, 14:14
  #1 (permalink)  
Thread Starter
 
Join Date: May 2015
Location: 26.83307 -80.104484
Age: 60
Posts: 49
Likes: 0
Received 0 Likes on 0 Posts
Question Helicopter Rotor Blade Radar (RODAR)

I've had this idea for decades and after having researched discovered there are numerous patents relating to the subject. Reading the abstracts, a main rotor based radar system makes great sense and provides for a very sensitive radar. Due to the width of the radome in relation to the size of the rotor disc a Synthetic Aperture Radar could be developed to rival or surpass anything currently available. For a helicopter this would provide 360* situational awareness, terrain avoidance, weather, obstacle detection etc. etc.


There are also patents relating to Electro-Optical systems built-in to the rotor blade tips. Combining both these technologies into the main rotor leaves the fuselage free of any aerodynamics robbing appendages and again just makes sense.


My question is, why have these ideas not gone any further? With today's miniaturization of electronic components, computing capability and composite materials along with the safety and operational benefits of developing such systems would seem to me to be a priority.

Last edited by SeaMac; 13th May 2015 at 18:54.
SeaMac is offline  
Old 13th May 2015, 19:19
  #2 (permalink)  
 
Join Date: Feb 2008
Location: USA
Posts: 93
Likes: 0
Received 0 Likes on 0 Posts
OK I'll bite since I design RADAR stuff amongst other things.

A quick "back of the fag packet calculation" gives me the following:

Lynx rotor disc diameter (as an example): 12.8M
Lynx blade tip speed: 700 feet/sec = ~ 214M/S

Centripetal Acceleration = (v*v)/r = (214 * 214)/6.4 = 7155 M/S^2
i.e 70g constant acceleration.

It's not exactly a friendly environment for a relatively massive, sophisticated and delicate piece of electronics then. Cooling at least would not be such a problem....

Then there's the pragmatic problem of how you service, power and communicate with it.

In other words I suspect that it has theoretical benefits as you point out but is in practical terms a non-starter.
ion_berkley is offline  
Old 13th May 2015, 19:37
  #3 (permalink)  
Thread Starter
 
Join Date: May 2015
Location: 26.83307 -80.104484
Age: 60
Posts: 49
Likes: 0
Received 0 Likes on 0 Posts
I believe one of the patent holders is Bell and they brought the system up to a technology demonstrator. Clearly it ran into issues, likely those mentioned above. As for servicing and powering, don't they operate rotor ice protection systems (RIPS) where there must be power and the ability to service the components?


I'm certain with at least the military application if it could be done it would have but then again DoD contractors tend to move at a snails pace when it comes to new technology. I'm just wondering with all that is new in technology why a system couldn't be made viable? Let me qualify myself here, I am not a pilot or engineer just someone who thinks too much sometimes.... lol
SeaMac is offline  
Old 13th May 2015, 19:44
  #4 (permalink)  
 
Join Date: Sep 2002
Location: Great South East, tired and retired
Posts: 4,349
Likes: 0
Received 193 Likes on 89 Posts
The frontal area for the antenna is only a couple of inches, which will govern the wavelength of the radar waves, which will govern how useful they are for detecting or penetrating cloud, aircraft, rocks etc.

The rotation rate of 5 per second is pretty fast and will govern the range of the radar (short), though I suppose it is only for really close-in stuff. There will also be doppler shift to deal with, as the antenna is not fixed.
Ascend Charlie is offline  
Old 13th May 2015, 23:03
  #5 (permalink)  
Thread Starter
 
Join Date: May 2015
Location: 26.83307 -80.104484
Age: 60
Posts: 49
Likes: 0
Received 0 Likes on 0 Posts
I know nothing of the specifics pertaining to operational characteristics of radar systems. I have read the patent applications from numerous sources mostly Electrical Engineers and in the abstracts and descriptions they proclaimed a very high degree of detail could be provided to the point of 3D Synthetic Aperture capability. In most instances the radar antennae itself was really no more than a wire installed within the leading edge of each rotor blade.
SeaMac is offline  
Old 14th May 2015, 06:08
  #6 (permalink)  
 
Join Date: Feb 2001
Location: West coast Australia :)
Posts: 238
Received 0 Likes on 0 Posts
As I understand it a RIPS system only has slip rings to transfer the electricity from one side of the swash plate to the other (fixed - moving). Not sure how intelligent the parts on the head and blades are other than heating mats and cables.

Si
bigglesbutler is offline  
Old 14th May 2015, 06:40
  #7 (permalink)  
 
Join Date: Jul 2005
Location: LFBO
Posts: 96
Likes: 0
Received 0 Likes on 0 Posts
I seem to remember something being shown on BBC TV with a very high definition image.

http://ieeexplore.ieee.org/ielx5/526...number=5268715
Been Accounting is offline  
Old 14th May 2015, 14:21
  #8 (permalink)  
Thread Starter
 
Join Date: May 2015
Location: 26.83307 -80.104484
Age: 60
Posts: 49
Likes: 0
Received 0 Likes on 0 Posts
I've seen the document you provided in the link, it's the Ferranti system one of many I discovered while researching USPTO applications.
SeaMac is offline  
Old 15th May 2015, 11:32
  #9 (permalink)  
 
Join Date: Apr 1998
Location: Mesopotamos
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
Seems to me that a lot of complex mathematics are required to determine the sensors whereabouts in relation to the returned radar signal. There's RRPM, pitch, flap, lead-lad, flex, twist, flutter, and probably more that needs calculating.

Although it seems like a good idea on paper, with sensor resolution continually increasing for any given size, then there may not be a requirement for locating a sensitive bit of equipment in such a hostile environment.
cattletruck is offline  
Old 16th May 2015, 09:40
  #10 (permalink)  
 
Join Date: Nov 2010
Location: Somerset
Posts: 24
Likes: 0
Received 0 Likes on 0 Posts
Something like this, you mean?




https://youtu.be/t-VTF-jZdUQ?t=41m40s
AArkley is offline  
Old 16th May 2015, 19:34
  #11 (permalink)  
Thread Starter
 
Join Date: May 2015
Location: 26.83307 -80.104484
Age: 60
Posts: 49
Likes: 0
Received 0 Likes on 0 Posts
@AArkley,


Yes, that is very similar to RODAR. Since the HeliRadar is a relatively recent system one developed in association with Eurocopter I have to assume that many of the challenges mentioned above have been addressed. Now to have the antennae integral with the rotor itself, I have no doubt that DARPA or some other entity is working on it.


BTW, it would have been nice of you to indicate the segment which mentioned the HeliRadar was @ 41:44, it would have saved me and possibly others from watching the entire video. Thank you though for sharing.
SeaMac is offline  
Old 17th May 2015, 00:00
  #12 (permalink)  
 
Join Date: May 2011
Location: In Communicado
Posts: 106
Likes: 0
Received 0 Likes on 0 Posts
For close-range obstacle detection, the AW139 has an option for LIDAR which will provide the crew with information on potential conflict with lateral obstructions. This is obviously not a "cruise flight" function, but one which will provide proximity information during hover operations.


Perhaps not what the OP was looking for, but which may be somewhat related.
HLCPTR is offline  
Old 17th May 2015, 02:08
  #13 (permalink)  
Thread Starter
 
Join Date: May 2015
Location: 26.83307 -80.104484
Age: 60
Posts: 49
Likes: 0
Received 0 Likes on 0 Posts
@HLCPTR,

Aware of LIDAR but not the same system. RODAR is integral to the main rotor therefore requires nothing to be mounted externally on the fuselage. If EO capability could be added to the rotor tips then not even a gimbal mounted EO sensor would be required affording a clean fuselage and the inherent increase in aerodynamic and thus fuel efficiency. Development stagnation could be nothing more than sorting out payment to the multitude of current patent holders. It's always about money in the end, even something that could definitely save lives...
SeaMac is offline  
Old 17th May 2015, 05:28
  #14 (permalink)  
 
Join Date: Mar 2012
Location: steady
Posts: 382
Received 2 Likes on 2 Posts
Why would you want to incorporate it in the blade tips? The obvious answer would be to just bolt your magic device on top of the rotor head. Most of the above mentioned problems would be overcome.
I wonder why EC appears to never having followed up on their patent from 15 years ago. BTW, they called it ROSAR, synthetic aperture radar with rotating antennas.
whoknows idont is offline  
Old 17th May 2015, 05:48
  #15 (permalink)  
Thread Starter
 
Join Date: May 2015
Location: 26.83307 -80.104484
Age: 60
Posts: 49
Likes: 0
Received 0 Likes on 0 Posts
@whoknows idont,

It's not me who wanted to put just the electro-optical sensors in the rotor blade tips, there's more than one patent for just that with the USPTO. With the integral to rotor radar and blade tip EO you would have both synthetic aperture capability along with HD day/night camera/IR/thermal imaging, all potentially combined on one screen providing the crew with the utmost in situational awareness. It is not magic it is technological reality with awarded US patents. I do not know why Eurocopter didn't continue with ROSAR, maybe it infringed on existing patents and they chose to stay out of litigation. My only question is why all of the patent holders and industry leaders have not made this technology available. I suspect it comes down to money, if in the 70's you designed a system and was awarded a patent -which it was- but for whatever reason stopped development you still own the patent so long as you kept it current. If say Raytheon, Airbus, Boeing or someone else wanted to continue development they have to buy the rights or pay royalties......all comes down to money. Then of course if Boeing ended up with the patent well then, there's no chance at all it'll be developed. Boeing IMHO is the embodiment of a truly evil corporation, but that's a whole other matter.
SeaMac is offline  
Old 17th May 2015, 06:28
  #16 (permalink)  
 
Join Date: Mar 2012
Location: steady
Posts: 382
Received 2 Likes on 2 Posts
What's the gain? At the tips you have to compensate for the variety of blade movement and for the means of that, exactly capture the blade tip movement. Otherwise get a pretty wobbly image. Seems terribly complicated, maybe impossible with 1970s technology.
On top of that, you have a much more exposed position, would need redesigned blades, tamper much more with the helicopters rotor system.
While you gain not one single rpm over the rotor head. So what's the unobvious angle here?
whoknows idont is offline  
Old 17th May 2015, 06:36
  #17 (permalink)  
 
Join Date: Dec 2008
Location: N/A
Posts: 845
Likes: 0
Received 0 Likes on 0 Posts
Math check

Originally Posted by ion_berkley
OK I'll bite since I design RADAR stuff amongst other things.

A quick "back of the fag packet calculation" gives me the following:

Lynx rotor disc diameter (as an example): 12.8M
Lynx blade tip speed: 700 feet/sec = ~ 214M/S

Centripetal Acceleration = (v*v)/r = (214 * 214)/6.4 = 7155 M/S^2
i.e 70g constant acceleration.

Err , maybe need to get your cigarette packet checked

Is 7155m/s^2 ~= 70g ? (More like: 700g)


i can understand that valves might have an issue at 700g, but why would a chip care about being at 700g ?
AnFI is offline  
Old 17th May 2015, 14:35
  #18 (permalink)  
Thread Starter
 
Join Date: May 2015
Location: 26.83307 -80.104484
Age: 60
Posts: 49
Likes: 0
Received 0 Likes on 0 Posts
@whoknows idont,

I'm sure the engineers and patent holders were hoping to gain 360* situational awareness and all-weather, day/night operational ability out of a rotorcraft platform. Personally I can think of one particular outfit that could significantly benefit from the technology......160th S.O.A.R. although they seem to do just fine without.

Computer software can stabilize virtually any image as for the rotor tip speed that too can be slowed and stabilized digitally so the image could very likely be HD.

I'm not the one driving this, just curious why with all the research and patents it's not made available. It just seems to me to offer so much in safety especially for SAR applications that the manufacturers would be clamoring to make it available.
SeaMac is offline  
Old 17th May 2015, 17:24
  #19 (permalink)  
 
Join Date: Mar 2012
Location: steady
Posts: 382
Received 2 Likes on 2 Posts
The rotor head also turns the full 360 degrees, just saying. I wonder, what the benefit of using the blade tips would be. Maybe the greater distance between the sensor and the rotational axis makes the picture so much better...
I also find it to be a quite intriguing question why this technology didn't cut the mustard yet.
Who knows, I don't.
whoknows idont is offline  
Old 17th May 2015, 17:40
  #20 (permalink)  
Thread Starter
 
Join Date: May 2015
Location: 26.83307 -80.104484
Age: 60
Posts: 49
Likes: 0
Received 0 Likes on 0 Posts
@whoknows idont,

I would think you would get a better view from the rotor tips as compare to the rotor head, at least being able to view beneath the aircraft for a full 3D picture even back to the fuselage itself.

You and I both wonder why it hasn't been brought to market. I believe it was about 20 years ago and I remember reading an article in Rotor magazine about technology to make flying at low levels safer. It involved cameras located all about the craft, live wire detection systems and so forth and all made perfectly logical sense. The rotor itself offers a perfect antennae and EO platform providing a 3D 360* view.

It could also be a liability concern, one entity responsible for the rotor itself, another for the radar then yet another for EO but all contained within one blade. So who do you sue if something goes wrong and your aircraft turns into a land dart or the rotor lops someone's head off?
SeaMac is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.