Setting Vref Approach speed 737
Thread Starter
Join Date: Jun 2015
Location: Hamburg
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
Setting Vref Approach speed 737
Would like to know how you handle setting the Vref Speed for the Approach. Are you Talking the current gross weight or overwritting it with the estimated? What are the advantages/disadvantages? Yesterday we had the Issue with the PFD showing a different Vref speed compared to the one in FMCs Approach page. How can this Happen?
thanks!
thanks!
Join Date: Jan 2006
Location: Between a rock and a hard place
Posts: 1,267
Likes: 0
Received 0 Likes
on
0 Posts
The Vref may change a knot or so between the brief and final approach. If you're unhappy with one knot difference then just update the PFD speed. Takes 2 button pushes. My opinion.
See the FCTM. If manual throttle, don't forget to bleed off the half the steady headwind component approaching touchdown that was added to VREF as well as the 10 knots added to VREF if ice additive. The latter 10 knots is reduced once below 200 feet.
Join Date: Jul 1999
Location: Out of a Suitcase
Posts: 155
Likes: 0
Received 0 Likes
on
0 Posts
The indications on the Speed Tape are for the aircraft weight at that moment.
FMC calculations are based on aircraft weight at the end of the inserted route.
In the event of an immediate return the route has to be cleared before looking at Vref otherwise it will be incorrect.
FMC calculations are based on aircraft weight at the end of the inserted route.
In the event of an immediate return the route has to be cleared before looking at Vref otherwise it will be incorrect.
Join Date: Aug 2016
Location: Brussels
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
The indications on the Speed Tape are for the aircraft weight at that moment.
FMC calculations are based on aircraft weight at the end of the inserted route.
In the event of an immediate return the route has to be cleared before looking at Vref otherwise it will be incorrect.
FMC calculations are based on aircraft weight at the end of the inserted route.
In the event of an immediate return the route has to be cleared before looking at Vref otherwise it will be incorrect.
True...FWIW a slightly different Boeing in question but FWIW our training department/management has just decreed, in the interests of minimising FMC punching after TOD, that one should select Vref at the briefing stage and then barring any major events such as a go-around leave it alone...
Join Date: Dec 2006
Location: australia
Posts: 916
Likes: 0
Received 0 Likes
on
0 Posts
FWIW where I am at present the F/O's are taught they MUST override the expected landing weight and set that Vref speed.
On occasion I point out to them, on final approach, that the FMC approach speed is actually 1 kt FASTER than the Vref they set due track shortening, damned fine efficient descent profile....whatever.
No hassles, just reselect the correct approach speed.
After landing I just discuss what would happen IF an accident occurred and in evidence it was found the crew were KNOWINGLY using an incorrect Vref setting for the actual landing weight??
Suppose whether the argument from the prosecution or defence in the courtroom!
Cheers.
On occasion I point out to them, on final approach, that the FMC approach speed is actually 1 kt FASTER than the Vref they set due track shortening, damned fine efficient descent profile....whatever.
No hassles, just reselect the correct approach speed.
After landing I just discuss what would happen IF an accident occurred and in evidence it was found the crew were KNOWINGLY using an incorrect Vref setting for the actual landing weight??
Suppose whether the argument from the prosecution or defence in the courtroom!
Cheers.
Requiring the speed to be checked and reset should trigger the reassessment of the speed required according to the landing conditions - operational requirement EASA, recommendation FAA.
FMC might have the forecast wind, but not actual or gusts / turbulence, which could require a higher speed.
The FMC would not have runway condition or braking action (unless entered), which should also influence speed selection or at least speed or configuration management. Which in turn should trigger the need to adjust landing performance / auto brake selection. Also act as a cross check of landing weight against the expected or computed value.
A good triggering procedure should force engagement of thought, opposed to blind following of some computed value.
So not having a display of computed value might be better.
Just because something can be done is not always a good idea, or because it reduces workload; we often fail to consider both technology accuracy - reliability, and human performance in our choice of action
FMC might have the forecast wind, but not actual or gusts / turbulence, which could require a higher speed.
The FMC would not have runway condition or braking action (unless entered), which should also influence speed selection or at least speed or configuration management. Which in turn should trigger the need to adjust landing performance / auto brake selection. Also act as a cross check of landing weight against the expected or computed value.
A good triggering procedure should force engagement of thought, opposed to blind following of some computed value.
So not having a display of computed value might be better.
Just because something can be done is not always a good idea, or because it reduces workload; we often fail to consider both technology accuracy - reliability, and human performance in our choice of action
Thread Starter
Join Date: Jun 2015
Location: Hamburg
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
So in Order to set the Target Speed.. which Vref Shall i Look to.. the one on the pfd or the one on the Fmc... theY differed Recently... that s why i am asking
Join Date: Jan 2006
Location: Between a rock and a hard place
Posts: 1,267
Likes: 0
Received 0 Likes
on
0 Posts
So in Order to set the Target Speed.. which Vref Shall i Look to.. the one on the pfd or the one on the Fmc... theY differed Recently... that s why i am asking
Join Date: Jan 2006
Location: Between a rock and a hard place
Posts: 1,267
Likes: 0
Received 0 Likes
on
0 Posts
FMC calculations are based on aircraft weight at the end of the inserted route.
In the event of an immediate return the route has to be cleared before looking at Vref otherwise it will be incorrect.
In the event of an immediate return the route has to be cleared before looking at Vref otherwise it will be incorrect.
Without knowledge of your aircraft, if the EFIS Vref display is automatic and associated with low speed awareness and stall (amber / red bands), normally based on AoA (certification basis), then this should be the more accurate (less susceptible to error) because AoA does not depend on wt. Alternatively is this the manual set speed via the FGC.
The FMS could use AoA, but from the discussion so far appears not, because the interface with wt.
Join Date: May 2019
Location: Somewhere over the rainbow...
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
A whole lot of hand wringing going on for what may be a knot or two. Do you "really" know what your aircraft weighs at any particular moment? Can you honestly hold your approach speed to that precision? Do you know exactly what the wind will be in the flare?
The FMC also produces a stab trim calculation to the hundredth digit. Can you even set it? Did you know that this setting is almost always wrong?
We used to have a saying at a previous employer about their approach to certain tasks: "Measure it with a micrometer, mark it with a grease pencil, cut it with a blow torch." This discussion kind of reminds me of that.
Yes, be close to approach speed when you start your flare. However, just as important: land in the touchdown zone, on centerline, no sideways drift, and (very, very important), throttles closed. Having your power up chasing a speed when you touchdown can cause you a world of hurt.
Bonus question: On the 737, would you rather have a crosswind from the left or the right? Why? How can you use that knowledge to your advantage with the wind straight down the runway?
The FMC also produces a stab trim calculation to the hundredth digit. Can you even set it? Did you know that this setting is almost always wrong?
We used to have a saying at a previous employer about their approach to certain tasks: "Measure it with a micrometer, mark it with a grease pencil, cut it with a blow torch." This discussion kind of reminds me of that.
Yes, be close to approach speed when you start your flare. However, just as important: land in the touchdown zone, on centerline, no sideways drift, and (very, very important), throttles closed. Having your power up chasing a speed when you touchdown can cause you a world of hurt.
Bonus question: On the 737, would you rather have a crosswind from the left or the right? Why? How can you use that knowledge to your advantage with the wind straight down the runway?
yoko1, similarly, how would you know if there was a gross error in one or the other value. Thus the need to know how each are calculated and which should have the greater integrity.
As with any 2 value, dual system, if there is an error between them, then the correct value cannot be found without a third source for comparison or a very good understanding of the origin of each value. e.g. obvious error in FMS wt.
As with any 2 value, dual system, if there is an error between them, then the correct value cannot be found without a third source for comparison or a very good understanding of the origin of each value. e.g. obvious error in FMS wt.
Join Date: May 2019
Location: Somewhere over the rainbow...
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
My point is that each of these sources are calculated values and can only be as precise as the inputs into those calculations. I've had my share of misloaded aircraft over the years, so it is advisable to apply an appropriate amount of vigilance to the FMC value. With enough time in the aircraft, a pilot should eventually get a sense whether the FMC calculated value that they are attempting to fly is appropriate for the conditions. Fortunately, the 737's I operate have a direct reading of the AOA vanes displayed on the PFD which provides a good sanity check for one's approach speed. That being said, this aircraft is far more tolerant of being a few knots fast than a few knots slow.
Join Date: Jul 2000
Location: West
Posts: 399
Likes: 0
Received 0 Likes
on
0 Posts
Join Date: Apr 2008
Location: Nearer home than before!
Posts: 524
Likes: 0
Received 0 Likes
on
0 Posts
My favourite speed for some reason....
Answer to Yoko is always land on the left wheel if you want a smooth touchdown. In our company we are required to brief before TOD and complete the descent checklist. The Assumed GW at touchdown is taken from the FMC progress page where you look at the difference between current and predicted. It's usually about a tonne. Then you go to the Init Ref and deduct this difference from current GW and double tap the speeds for the flap setting. You can pop in plus 5 on the next line or more if you wish, though it's just as easy to manually set that on getting the touchdown wind from ATC.
This flying game is not rocket science, yet youngsters are taught so much by rote now that they hang their hats on flying numbers at all times. It's a world of butt covering and legal minefields. and I'm counting the days till I can retire. I blame the culture on Boeing and Airbus lawyers and the dumbing down it entails. I've never flown a type where I was taught and expected to know so little about the airframe!
So yes, left side first. It needs a minute or two of reading the WOW sensor logic to understand why, and the number of blank and confused faces I've had alongside me who can't understand it after four hours of trying never ceases to amaze me. They're the future and single pilot aircraft will be designed for them to fly, not the likes of me. That really scares me!
Answer to Yoko is always land on the left wheel if you want a smooth touchdown. In our company we are required to brief before TOD and complete the descent checklist. The Assumed GW at touchdown is taken from the FMC progress page where you look at the difference between current and predicted. It's usually about a tonne. Then you go to the Init Ref and deduct this difference from current GW and double tap the speeds for the flap setting. You can pop in plus 5 on the next line or more if you wish, though it's just as easy to manually set that on getting the touchdown wind from ATC.
This flying game is not rocket science, yet youngsters are taught so much by rote now that they hang their hats on flying numbers at all times. It's a world of butt covering and legal minefields. and I'm counting the days till I can retire. I blame the culture on Boeing and Airbus lawyers and the dumbing down it entails. I've never flown a type where I was taught and expected to know so little about the airframe!
So yes, left side first. It needs a minute or two of reading the WOW sensor logic to understand why, and the number of blank and confused faces I've had alongside me who can't understand it after four hours of trying never ceases to amaze me. They're the future and single pilot aircraft will be designed for them to fly, not the likes of me. That really scares me!
Join Date: Jan 2006
Location: US
Posts: 2,205
Likes: 0
Received 0 Likes
on
0 Posts
It’s Vref +7 in your example even at the higher AOA limit of the ‘on speed’ range.
The green band band covers a significant speed range and isn’t as accurate as military AOA ‘on speed’ green donuts. Because of that range/inaccuracy (roughly 2.5 units) it’s not used as a primary performance instrument.