When do we announce V1 & rotate on A320
5-7 knots..... who is saying that?
just announce it as close to the speed as you can.
You still have the recognition/response delay from certification up your sleeve For a go or no go decision.
personally I prefer an earlier go decision 1 second prior to V1, than no go at V1 + 3 seconds. Both are certified, one gives a lot more margin.
just announce it as close to the speed as you can.
You still have the recognition/response delay from certification up your sleeve For a go or no go decision.
personally I prefer an earlier go decision 1 second prior to V1, than no go at V1 + 3 seconds. Both are certified, one gives a lot more margin.
Join Date: Sep 2003
Location: Sand pit
Age: 54
Posts: 460
Likes: 0
Received 0 Likes
on
0 Posts
that definitely gives you more margin for stopping, but if a balanced field length V1 is also minimum speed to continue, rotate and climb to 35 feet by end of runway? If you decide to continue when that much slower you may not like the results
Join Date: Aug 2013
Location: PA
Age: 59
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
When do we announce V1 & rotate. Some people say , announce it 5-7 kts before reaching that vspeed .
So you know, it is assumed there is a 7 second delay, so when the ac says rotate, it assumes it takes 2 seconds for the pilot to comprehend, 2 seconds to move the controls, and 3 seconds for the ac to respond....
Join Date: Nov 2004
Location: bkk
Posts: 285
Likes: 0
Received 0 Likes
on
0 Posts
Since around 15 years ago, and I seem to recall it came out of either a safety forum related to the rejected takeoff issue or it was from Flight Safety Foundation, it was RECOMMENDED to actually utter the word VEE- ONE at the computed V1 minus 5 knots.This is very good practice and should be applied everywhere.The reasoning is the V1 does not change at all, however the words VEE ONE will be stated by the PM just prior to V1 thus allowing the pilot in the left seat to make his go/no go decision at or before, but not later.Many many times in the simulator I have seen pilots try to reject just slightly after V1 and while most of the time with long runways you get away with this but in the most limiting cases you run the serious risk of an over run/crash.
I am aware of many airlines having this technique in their SOPs but everybody should apply this.Its safer.
I am aware of many airlines having this technique in their SOPs but everybody should apply this.Its safer.
Join Date: Jun 2007
Location: Wanderlust
Posts: 3,407
Likes: 0
Received 0 Likes
on
0 Posts
There is no reason to call Vr early, so why would you?
Join Date: Apr 2010
Location: London
Posts: 319
Likes: 0
Received 0 Likes
on
0 Posts
I agree with Feather44. Call it when it your at V1. What next, make adjustments for someone's rate of speech? Intonation? Dialect? Cant even believe it Is worthy of any other consideration. To suggest any other option is madness and lunacy and to enter the world of a test pilot.
What sort of stupid second guessing question is this?
The A330 and A350 all have auto V1 callouts and they occur AT V1....not before......
Stop trying to complicate things.
just do what Airbus and your training department tells you.
The A330 and A350 all have auto V1 callouts and they occur AT V1....not before......
Stop trying to complicate things.
just do what Airbus and your training department tells you.
Gender Faculty Specialist
Personally, as PF, I keep half an eye on the ASI anyway so if anyone forgets to call V1, calls it late or early then I’ve already made my mind up what I’m going to do.
And let’s not pretend that actual performance matches exactly that which was calculated so keeping an eye on your speed and runway remaining will allow you to make a judgement call at the time.
And let’s not pretend that actual performance matches exactly that which was calculated so keeping an eye on your speed and runway remaining will allow you to make a judgement call at the time.
Well the Airbus opinion on the matter (refer the STOP/GO FOBN) which reflects regulatory definitions of V1 being the maximum speed at which a takeoff may be discontinued is:
Logic says that if the decision is to be made by or at V1, then the call can’t be made at V1.
Having said that, look at the ASI permitted discrepancies from CM1 to CM2 ...
V1 is considered to be the end of the STOP or GO decision-making process. Therefore, at the latest, this decision must be made at V1, so that the Captain can initiate the STOP actions as close to V1 as possible: V1 is indeed a decision/action speed.
Having said that, look at the ASI permitted discrepancies from CM1 to CM2 ...
Only half a speed-brake
Why not? If you call V1 at the speed exactly, then you simply do not stop once the words are spoken.
Anyways, I was trained to announce so that the callout is finished by the time we are passing the last action speed (v1). Guess about 1 sec is needed. Any captain is surely looking at his ASI at that stage, there is little practical benefit in digging deeper.
-7kt would be definitely non-compliance.
AFAIK Lufthansa uses a different call, and I admit to love their thinking. Same time, same use, yet another word. It is one syllable, so the timing becomes irrelevant. It removes ANY ambiguity about the decision/action meaning. They say ........ “go”.
Vorsprung durch Expertise, there you have it. In that light a “vee-one” call or this discussion is quite 1950s.
-7kt would be definitely non-compliance.
AFAIK Lufthansa uses a different call, and I admit to love their thinking. Same time, same use, yet another word. It is one syllable, so the timing becomes irrelevant. It removes ANY ambiguity about the decision/action meaning. They say ........ “go”.
Vorsprung durch Expertise, there you have it. In that light a “vee-one” call or this discussion is quite 1950s.
Last edited by FlightDetent; 12th Dec 2018 at 04:48.
Join Date: Sep 1998
Location: wherever
Age: 55
Posts: 1,616
Likes: 0
Received 0 Likes
on
0 Posts
Auto call outs do it at V1. Ive seen a lot of airlines SOPs. Probably 60 or more over the years. Most call AT v1. A couple of years ago some changed to calling x kt before but most have changed back to At. Some changed to "go" some of those have changed back to "V1".
All much of a muchness really. As PF don't reject above V1. Simple.
All much of a muchness really. As PF don't reject above V1. Simple.
Auto call outs do it at V1.
Join Date: May 2009
Location: london
Posts: 137
Likes: 0
Received 0 Likes
on
0 Posts
Might just be me but the V1 call is only part of the go-nogo for me. What defines the go-nogo is the actual indicated speed. If the PM chooses to call V1 early I will assume the ASIs are reading differently for some reason and be prepared for unreliable airspeed. If I am handling I will have the ASI in my scan and know when I am through 80kts, am passing V1, and rotate. If you are dependent on the V1 call or rotate call you will have lost an opportunity to find out that your pitot is blocked..
Don’t forget the 1 second of recognition time, so on a FLEX takeoff at reasonable OAT “should be good” if the aircraft is stopping by V1 + 3sec. Personally, not a chance in hell.