Landing gear lean question?
Thread Starter
Join Date: Aug 2013
Location: PA
Age: 59
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for all of the replies.....
Looking at the different ac's on final, and the angles with the fuselage, could it be to help prevent tailstrike?
or perhaps to help get the ac on the runway with the associated ground effects?
Looking at the different ac's on final, and the angles with the fuselage, could it be to help prevent tailstrike?
or perhaps to help get the ac on the runway with the associated ground effects?
Only the 777-300ER has that facility, and it's only used on takeoff, not on landing.
Does anyone know how the bogies are actually held at a specific tilt angle? Gravity seems a little iffy -- I assume the pivot point has to be centered between the axles to distribute weight evenly on the ground, so presumably the bogie's balanced pretty well. It seems like a fairly simple spring could bias it to one stop or the other without too much fuss, though.
The tilt angle must make an aerodynamic difference. Maybe it can be reversed or adjusted during design if there's excessive buffeting (or something like that) with the gear down?
Finally, though I doubt this is a significant design consideration, I'd guess that toes up or down affects wheel spin-up (and perhaps tire wear). The tires that touch down first are under very little load until the other axle touches, so it seems like they'd spin up more slowly.
The tilt angle must make an aerodynamic difference. Maybe it can be reversed or adjusted during design if there's excessive buffeting (or something like that) with the gear down?
Finally, though I doubt this is a significant design consideration, I'd guess that toes up or down affects wheel spin-up (and perhaps tire wear). The tires that touch down first are under very little load until the other axle touches, so it seems like they'd spin up more slowly.
Join Date: Jan 2002
Location: West Country
Posts: 1,271
Likes: 0
Received 0 Likes
on
0 Posts
On the 777 the gear is positioned by the tilt actuator to 5 degrees nose down for retraction and to 13 degrees nose up for landing - gravity has nothing to do with it, just good old hydraulic pressure.
its£5perworddammit
Join Date: Nov 2003
Location: the foxhole
Posts: 148
Likes: 0
Received 0 Likes
on
0 Posts
My question is - if this is the case - why does it go to the same nose up position initially on takeoff? Seems to be a lot of unnecessary acrobatics for it to pitch nose nown on rotation, then intentionally nose up 13 degrees, only to go 5 degs nose down again for retraction.
Join Date: Jan 2002
Location: West Country
Posts: 1,271
Likes: 0
Received 0 Likes
on
0 Posts
When the gear is selected up then Hyd pressure is diverted one side of the actuator to position the truck to -5°. If the gear is selected down then pressure goes to both sides of the actuator to position it to +13° (due to differential areas). This pressure stays there and the truck simply moves to desired position when weight is removed on takeoff.
Hope thats clear.
Hope thats clear.
its£5perworddammit
Join Date: Nov 2003
Location: the foxhole
Posts: 148
Likes: 0
Received 0 Likes
on
0 Posts
Good info - thank you.
Just to satisfy my curiosity, what would it look like then if we do a gravity drop with no hydraulic pressure? Is this something thats ever done in mx on jacks?
Just to satisfy my curiosity, what would it look like then if we do a gravity drop with no hydraulic pressure? Is this something thats ever done in mx on jacks?
Join Date: Jan 2002
Location: West Country
Posts: 1,271
Likes: 0
Received 0 Likes
on
0 Posts
You do a gravity drop every time you lower the gear - the 777 doesn't have hyd gear lowering.
If you lost Centre system hyd pressure then you lose truck positioning.
If you lost Centre system hyd pressure then you lose truck positioning.
its£5perworddammit
Join Date: Nov 2003
Location: the foxhole
Posts: 148
Likes: 0
Received 0 Likes
on
0 Posts
Thank you. And digging into the books for the A330 it appears the pitch trimmer here does the same thing - positions the bogie nose up on gear down selection. So the nose up orientation is very much intentional - and not because of gear bay fitment (or weight).
Always a good day to prove myself wrong and learn something!
Always a good day to prove myself wrong and learn something!
If you port pressure to both ends of an ordinary hydraulic cylinder, it will extend (because the rod occupies some of the effective area on its side of the piston.) So if all else is truly equal, nose-up or nose-down tilt might be driven by whether it was more convenient to mount the actuator toward the forward or aft end of the bogie.
Re Mr.Fox's posts, gravity extensions are done on jacks in the hangar usually after major gear maintenance. Without hydraulic pressure and air flow to influence bogie position it usually tilts to the heaviest end as you might expect.
The A330/A340 main gear is a special case. The nose up tilt is indeed intentional and is meant to act a bit like the 777-300ER's semi-levered gear in improving aft fuselage clearance. However, on retraction the gear actually shortens and this process removes the bogie tilt as it retracts so the bogie is parallel to the fuselage centreline when in the wheel well. The shock absorber strut slides inside the main fitting (the undercarriage leg) and is pulled up inside the leg as it retracts which removes the bogie tilt as well as shortening the length of the whole landing gear.
See video https://www.youtube.com/watch?v=-_z-KBTZRVk
The A330/A340 main gear is a special case. The nose up tilt is indeed intentional and is meant to act a bit like the 777-300ER's semi-levered gear in improving aft fuselage clearance. However, on retraction the gear actually shortens and this process removes the bogie tilt as it retracts so the bogie is parallel to the fuselage centreline when in the wheel well. The shock absorber strut slides inside the main fitting (the undercarriage leg) and is pulled up inside the leg as it retracts which removes the bogie tilt as well as shortening the length of the whole landing gear.
See video https://www.youtube.com/watch?v=-_z-KBTZRVk
I thought about this post for a while, and don't see that this is true. Let's say you land with the nose cabbed to the left. If the front of the bogey touches down first, the gear leg will twist counterclockwise as seen from above. If the rear touches down first, it will twist clockwise. But in both cases the angle of contact will pull the gear leg to the left, which is behind the CG, therefore stabilizing the plane in yaw. And in neither case would the leg twisting moment be greater than the other, at last for any reason that I can see.
I pondered for some time
However, having flown the 757 with a
trailing bogie and the 767 with forward
‘trail’ I can tell you the latter is far less
forgiving
The design seems to magnify touchdown
forces!
I suspect the same happens on the A380
and perhaps the A350