BA A320 v TUG at LHR on taxi
Thread Starter
Join Date: Feb 2002
Location: Dubai
Posts: 141
Likes: 0
Received 0 Likes
on
0 Posts
BA A320 v TUG at LHR on taxi
i am surprised this has not been mentioned because it happened over 24 hours ago. i was actually looking forward to the posts !
At 16:45z BA A320 (G-EUUF) had pushed back from stand 139 at LHR into the "K" apron ready for aflight to MUC.
ground engineer showed the pin to the flight Crew from the Starboard side of the aircraft. Aircraft started to taxi and hit the tug that had just disconnected.
It appears the tug driver after pushback could not move the tug.
They tried to get the attention of the flight crew but by then the tug had caused a few pennies worth of damage to No2 Engine.
Couple of questions for you drivers and Ground engineers.
Drivers .... Even after being shown the pin , dont you check left and right to make sure it is safe to taxi and not hit any small obstacles like a towbarless aircraft tug.
Or do you take it as a matter of course that the coast is clear.
Engineers .... should you check that everything is clear of the aircraft before showing pin.
AAIB were on site doing the necessary.
Significant damage to the underneath of No 2 engine. I have pics but cannot attach them for some reason !!
Happy Taxing
At 16:45z BA A320 (G-EUUF) had pushed back from stand 139 at LHR into the "K" apron ready for aflight to MUC.
ground engineer showed the pin to the flight Crew from the Starboard side of the aircraft. Aircraft started to taxi and hit the tug that had just disconnected.
It appears the tug driver after pushback could not move the tug.
They tried to get the attention of the flight crew but by then the tug had caused a few pennies worth of damage to No2 Engine.
Couple of questions for you drivers and Ground engineers.
Drivers .... Even after being shown the pin , dont you check left and right to make sure it is safe to taxi and not hit any small obstacles like a towbarless aircraft tug.
Or do you take it as a matter of course that the coast is clear.
Engineers .... should you check that everything is clear of the aircraft before showing pin.
AAIB were on site doing the necessary.
Significant damage to the underneath of No 2 engine. I have pics but cannot attach them for some reason !!
Happy Taxing
Join Date: May 2000
Location: Camp X-Ray
Posts: 2,135
Likes: 0
Received 0 Likes
on
0 Posts
Interesting! I could be mistaken but I understood that BA SOPs required the tug and all personnnel to be well clear of the aircraft before giving the flight crew the signal in order to prevent exactly this sort of occurrence. Even with that most people have a good look left and right with a verbal "Clear left/right" as an unofficial SOP call before moving off. On a 320 you'd definitely see a tug in the way of the #2.
Join Date: May 2002
Location: somewhere near an airport
Posts: 173
Likes: 0
Received 0 Likes
on
0 Posts
your right-it must be sop for all pilots let alone airlines that the FINAL clear left/right is done.
Also the whole point of the groundsman showing the pin to the crew (and getting ackknowlagement) is that all ground equipment is clear of aircraft,and that includes a huge many tonned tug
Also the whole point of the groundsman showing the pin to the crew (and getting ackknowlagement) is that all ground equipment is clear of aircraft,and that includes a huge many tonned tug
Join Date: Jan 2004
Location: Manchester
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
Southern Duel, 'Ground Engineer' doesn't get involved with pushbacks at BA anymore, this task is now performed (for years now) by the ground movements people, i.e. the tug crew department.
You don't show the pin until everything is physically clear, that's the whole fundamental point because the flight crew cannot see around the aircraft, the bigger the aircraft the worse the visibility becomes.
You don't show the pin until everything is physically clear, that's the whole fundamental point because the flight crew cannot see around the aircraft, the bigger the aircraft the worse the visibility becomes.
Join Date: Mar 1999
Location: New York
Posts: 196
Likes: 0
Received 0 Likes
on
0 Posts
Hi,
Would just like to confirm AUTOGLIDES post that there wouldn't have been an Engineer anywhere near that aircraft on departure.
Perhaps there should have been..
Just arent enough of us to go round these days!
LP
Would just like to confirm AUTOGLIDES post that there wouldn't have been an Engineer anywhere near that aircraft on departure.
Perhaps there should have been..
Just arent enough of us to go round these days!LP
Guest
Posts: n/a
tug
In BA the showing of the steering pin to the pilot is also an indication that all ground equipment is clear. Admittedly I would imagine one or other of the pilots should be able to see a tug from a small aircraft like the A320, but you would have no chance of seeing it on the 747.
its about 15 years since i did the headset on pushbacks. but the procedures were drummed into me and i still remember them clearly (about the only thing i can these days).
when the push was complete:
"push complete-set brakes"- "brakes set."
"we are disconnecting towbar."
when towbar and tug are clear- discinnect steering cut off pin.
"tug and bar clear, pin out, will signal you when i am clear"
simple, but seemed to work
when the push was complete:
"push complete-set brakes"- "brakes set."
"we are disconnecting towbar."
when towbar and tug are clear- discinnect steering cut off pin.
"tug and bar clear, pin out, will signal you when i am clear"
simple, but seemed to work
Join Date: Jul 2001
Location: London
Posts: 389
Likes: 0
Received 0 Likes
on
0 Posts
I agree with ASW driver. A visual check by the crew is obviously expected and logical, but we need to acknowledge the restricted view.
Personally whenever I've done headsetting in the past I would remain connected (and make sure flight deck know I'm still connected!) until the ground equipment is clear (or at least clearing) and visible to crew.
Personally whenever I've done headsetting in the past I would remain connected (and make sure flight deck know I'm still connected!) until the ground equipment is clear (or at least clearing) and visible to crew.
Join Date: Mar 2005
Location: England
Posts: 730
Likes: 0
Received 0 Likes
on
0 Posts
Le Pen
It is true at BA in the Uk at least that engineers are not present at departures and that the towing crew do a walkround and remove the pins.
Not sure what happens at this particular outstation though.
Fargoo
It is true at BA in the Uk at least that engineers are not present at departures and that the towing crew do a walkround and remove the pins.
Not sure what happens at this particular outstation though.
Fargoo
Junior trash
Join Date: Nov 1999
Location: UK
Posts: 1,025
Likes: 0
Received 0 Likes
on
0 Posts
Heathrow an outstation??
BA tug drivers are supposed to park in front of the aircraft in a position visible to the pilots until all other personnel are clear and then drive off. They never do.
BA tug drivers are supposed to park in front of the aircraft in a position visible to the pilots until all other personnel are clear and then drive off. They never do.
Join Date: Oct 2000
Location: Out of the blue
Posts: 162
Likes: 0
Received 0 Likes
on
0 Posts
After the first flight of the day, any transit Heathrow is an outstation until last landing - probably coz some clown thinks its cheaper. It may be of note that the engine is not visible from the flightdeck without physically opening the window and shoving your head out.
I shouldn't worry about apportioning blame and exacting painful and excruciating revenge - it's the only thing the management are good at.
I shouldn't worry about apportioning blame and exacting painful and excruciating revenge - it's the only thing the management are good at.
Join Date: Mar 1999
Location: New York
Posts: 196
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Fargoo
Le Pen
It is true at BA in the Uk at least that engineers are not present at departures and that the towing crew do a walkround and remove the pins.
Not sure what happens at this particular outstation though.
Fargoo
It is true at BA in the Uk at least that engineers are not present at departures and that the towing crew do a walkround and remove the pins.
Not sure what happens at this particular outstation though.
Fargoo
Twas LHR
LP
Join Date: Jun 2001
Location: the old shed next to the runway...
Posts: 59
Likes: 0
Received 0 Likes
on
0 Posts
Maybe It is time that BA introduced a Japanese style salute procedure on departure, that should dispel any problems with tug breaking down... 
That should go down well with the ground ops guys!
That should go down well with the ground ops guys!
Last edited by blackbox; 29th Jun 2006 at 05:12.
Join Date: Apr 2005
Location: UK
Posts: 459
Likes: 0
Received 0 Likes
on
0 Posts
Just look at some departures, Tug will disconnect from Aircraft and move/stop on one side of the Aircraft aft of the Cockpitt.
.
Me thinks Tug should be well fwd of the Aircraft so it's in plane view of the pilots.
.
Many people around Aircraft have not seen them Bite, but Bite they do and then everybody is interested for a while, blame the weather or anythink you can, but never blame a total lack of interest or understanding of some people who work with Aircraft.!!!
.
Me thinks Tug should be well fwd of the Aircraft so it's in plane view of the pilots.
.
Many people around Aircraft have not seen them Bite, but Bite they do and then everybody is interested for a while, blame the weather or anythink you can, but never blame a total lack of interest or understanding of some people who work with Aircraft.!!!
Join Date: Aug 2001
Location: BFS
Posts: 152
Likes: 0
Received 0 Likes
on
0 Posts
Showing 'the pin' indicates that the steering has been reconnnected, a final thumbs up declares that the tug (and anything else) has moved clear and it is safe to taxi.
Showing the pin and giving the thumbs up are frequently done together as the time taken for the pin to get from the nosewheel to a position in view of the cockpit allows enough time for the tug to have been removed.
Showing the pin and giving the thumbs up are frequently done together as the time taken for the pin to get from the nosewheel to a position in view of the cockpit allows enough time for the tug to have been removed.
Join Date: Sep 2002
Location: Middlesesx
Posts: 2,075
Likes: 0
Received 0 Likes
on
0 Posts
I have to take issue over the remark about BA management. As always is the case no action will be taken whatsoever save a costly investigation and retraining of the headset / tug driver. If there was a bit more discipline within BA and a few dismissals these things would not happen with such frequencies?
"Thanks, Ground. Disconnect, button up, have a final look around and show me the nose gear pin and intercom plug, then give me a thumbs up when we're safe to go"
Or words to that effect. That's what we used to teach in HM's Vickers FunBus. Presumably we learned that from BOAC?
Or words to that effect. That's what we used to teach in HM's Vickers FunBus. Presumably we learned that from BOAC?
