Police helicopter crashes onto Glasgow pub
Purveyor of Egg Liqueur to Lucifer
impressive quoting skills SS !
The thing about AnFI's reference is that the person in the tale got into the habit of leaving the transfer pumps on in order to not fall into the same trap of the tall fellow in the tale, that left them switched off. (Presumably, tall chap forgot, on this one occasion, to switch them on during the start up/pre take off phase as per the 105 FLM?)
The quoted person, therefore never did a shutdown or start up as per the FLM in all his time on the 105, and when the time came to complete a proper start up, with all the switches correctly in the off position, because of the non conformal procedure that had become his habit, the transfer pumps problem arose. (Not being a 105 man, I presume there is no transfer pump warning light that would say they were switched off?)
If the man in the tale had adopted the habit described on a 135 there would be a few indicators the pumps were off, not necessarily to prevent actual flight with the transfer pumps off, but at least they would tell the pilot that they were.
For example.
Switchology - Prime and transfer pump switches are next to each other. Post engines start, prime pumps are switched off, transfer pumps are switched on.
Visual indicators - When the prime pumps are on the CAD indicates this. When the Transfer pumps are off, the CAD also indicates this. Monitoring of fuel levels.
Procedures - Pre flight systems checks, Pre start checks, Pre take off checks, Take off checks, 'CAD indications'.
If the habit adopted by the chap in the tale quoted by AnFI was to 'follow the instructions in the FLM' instead of adopting his different set of start up/shut down procedures, then the problem he found himself in wouldn't have happened. Nothing to do with a complexity or simplicity of any particular system, simply a human failing from not following the correct procedures.
I'm often asked, why do you switch off the inverter?
My answer, because that's what is says to do in the FLM when closing down.
Here's a 135 question, how many engines are running when you do the Hyd checks?
Join Date: Aug 2006
Location: nice house
Age: 57
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
Sid, with regard to your last post....I fully agree..
One, with N2 appr 73-74%, don't do it in the powertrain accelleration phase.....so here"s a follow up question: Is it allowed to do it with both engines idle?
Here's a 135 question, how many engines are running when you do the Hyd checks?
Join Date: Jul 2000
Location: Nova
Posts: 1,242
Likes: 0
Received 0 Likes
on
0 Posts
ElectricJohn
You sure? That isn't what the AAIB said.
The aircraft's final resting position depends only upon what is supporting it, and where!
There are scenarios which fit all that you have described. Tumbling seems very unlikely to me.
It didn't - it was nose-down.
The aircraft's final resting position depends only upon what is supporting it, and where!
There are scenarios which fit all that you have described. Tumbling seems very unlikely to me.
Purveyor of Egg Liqueur to Lucifer
.....so here"s a follow up question: Is it allowed to do it with both engines idle?
(Flight idle)
Last edited by SilsoeSid; 15th Jan 2014 at 14:43. Reason: Engines at flight idle not ground
Purveyor of Egg Liqueur to Lucifer
Is there any suggestion the aircraft was at low speed/hover immediately prior to the accident?
Join Date: Jul 2000
Location: Nova
Posts: 1,242
Likes: 0
Received 0 Likes
on
0 Posts
ElectricJohn
Please don't think I'm being obtuse, but I don't think it's possible to draw that conclusion? All the photographs I have seen speak only to the final resting position of the aircraft, not the moment of impact.
There is a reasonably straightforward theory which 'fits', but not one I am prepared to put forward, as it would be totally speculative.
The only people with any factual idea are in Farnborough. We will hear from them when they consider it appropriate and accurate.
It does appear to have been angled downwards at impact though, from the pictures.
I'm actually more curious as to why there doesn't seem to have been much discussion about why it might have been flying very low and making odd noises some time before whatever caused the final crash sequence.
The only people with any factual idea are in Farnborough. We will hear from them when they consider it appropriate and accurate.
Join Date: Feb 2009
Location: Aberdeen
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
Re 'nose down' resting angle. Helicopter, in more or less level attitude, pancakes onto flat roof, with fuselage (bulk of weight) in middle of roof, tail close to edge. Roof is strongest nearest edge (walls), but subjected to greatest force at weakest point, nearest (unsupported) middle. Nose penetrates further into building than tail. Thus apparent nose down angle - little or nothing to infer in terms of how/why the helicopter crashed onto it.
Avoid imitations
Join Date: Nov 2000
Location: Wandering the FIR and cyberspace often at highly unsociable times
Posts: 14,582
Received 440 Likes
on
233 Posts
The horizontal stabiliser would still have an aerodynamic effect during a high rate of descent, rotors turning or not.
Purveyor of Egg Liqueur to Lucifer
Going back over a thousand posts, http://www.pprune.org/8194594-post783.html
Join Date: Jul 2000
Location: Nova
Posts: 1,242
Likes: 0
Received 0 Likes
on
0 Posts
SS
You seem to imply in that post that both engines were 'closed down'? That would require both intent and action. I don't think there is evidence yet to support that? Though I do agree with you in some other aspects.
Any tail rotor/fenestron failure I can imagine, would likely have been flyable down to very low speeds. (perhaps our EC135 pilots could help?) Apart from when virtually in the hover, I would imagine massively out of balance powered flight (indeed anything) would be preferable to autorotation into a city centre?
Unless at very low speed, tail rotor failure might not fit the little known information???
You seem to imply in that post that both engines were 'closed down'? That would require both intent and action. I don't think there is evidence yet to support that? Though I do agree with you in some other aspects.
Any tail rotor/fenestron failure I can imagine, would likely have been flyable down to very low speeds. (perhaps our EC135 pilots could help?) Apart from when virtually in the hover, I would imagine massively out of balance powered flight (indeed anything) would be preferable to autorotation into a city centre?
Unless at very low speed, tail rotor failure might not fit the little known information???
Purveyor of Egg Liqueur to Lucifer
Tr, you're quite right, you can control a tail rotor problem on a 135 quite well, even down to a run on, as long as she doesn't break away below 40 kts. Wind from the left is a good thing, which it was on the night.
Tr drive/control failure drills look for an airspeed of at least 70kts, once you've got out of the initial situation then you can see if you can achieve the 40 kts on approach or not. However what if there's the tail problem on reducing through 80kts, power pulled to try and get airspeed on, and it starts to go wrong? If you're spinning (eye witnesses), how long do you try and get airspeed over the fin? At some point, the twist grips have to be a consideration, and then you deal with the cards dealt, ie your going where your right foot is!
All of this didn't happen near to the pub, that's just where it all finished.
Until we have the gps info such as speed & height and switch positions, we have very little to go on. However, it still leaves us with the question of how the blades were not rotating on impact.
All the above is well and good if the ac is complete, but are there any thoughts on whether the tail might have partially separated pre impact?
Tr drive/control failure drills look for an airspeed of at least 70kts, once you've got out of the initial situation then you can see if you can achieve the 40 kts on approach or not. However what if there's the tail problem on reducing through 80kts, power pulled to try and get airspeed on, and it starts to go wrong? If you're spinning (eye witnesses), how long do you try and get airspeed over the fin? At some point, the twist grips have to be a consideration, and then you deal with the cards dealt, ie your going where your right foot is!
All of this didn't happen near to the pub, that's just where it all finished.
Until we have the gps info such as speed & height and switch positions, we have very little to go on. However, it still leaves us with the question of how the blades were not rotating on impact.
All the above is well and good if the ac is complete, but are there any thoughts on whether the tail might have partially separated pre impact?
Join Date: Jul 2000
Location: Nova
Posts: 1,242
Likes: 0
Received 0 Likes
on
0 Posts
However what if there's the tail problem on reducing through 80kts
En-route back to base, one minute out, slow(ing) to below 80 kts in order to raise downlink and/or arm flotation gear?
Ergo, very little torque demanded? Very little tail rotor authority required, a bit like your 40kts example.
The only way I can see tail rotor failure requiring immediate autorotation into a city centre is if the failure happened in OGI hover? Is that fair, and do we think it was hovering immediately prior to the accident? (That's not what they are reported to have told ATC?)
All idle speculation of course.
Avoid imitations
Join Date: Nov 2000
Location: Wandering the FIR and cyberspace often at highly unsociable times
Posts: 14,582
Received 440 Likes
on
233 Posts
All the above is well and good if the ac is complete, but are there any thoughts on whether the tail might have partially separated pre impact?
I wonder how far the frame can partly separate and distort and "lean back" before the rear driveshaft disengages?
Purveyor of Egg Liqueur to Lucifer
No 135 pilot, or I'd hazard a guess any helicopter pilot with a tail rotor problem, would continue straight into any base, let alone one such as Glasgow.
They asked air traffic for clearance into the zone to return to base, they wouldn't have needed to tell them they were doing anything on the way in, unless perhaps it caused a delay. They could well have slowed over the city to 'have a look at something', at which point something possibly happened, again the GPS info should tell us.
They asked air traffic for clearance into the zone to return to base, they wouldn't have needed to tell them they were doing anything on the way in, unless perhaps it caused a delay. They could well have slowed over the city to 'have a look at something', at which point something possibly happened, again the GPS info should tell us.
Join Date: Jul 2000
Location: Nova
Posts: 1,242
Likes: 0
Received 0 Likes
on
0 Posts
Shy.
Reminds me of an accident to a B206 G-WLLY.
Sid
I don't think I ever said that's what he was intending? I just said pretty much any form of continued flight offered a better chance of survival than autorotation into a city centre.
Tail rotor failure in OGI hover is the only regime I can imagine that would require such extreme action, (take a look at YouTube for some examples) and I haven't heard any witness statements say he was hovering?
That is all.
Reminds me of an accident to a B206 G-WLLY.
Sid
No 135 pilot, or I'd hazard a guess any helicopter pilot with a tail rotor problem, would continue straight into any base, let alone one such as Glasgow.
Tail rotor failure in OGI hover is the only regime I can imagine that would require such extreme action, (take a look at YouTube for some examples) and I haven't heard any witness statements say he was hovering?
That is all.
Last edited by Tandemrotor; 15th Jan 2014 at 20:14.
Join Date: Dec 2007
Location: Pasadena
Posts: 633
Likes: 0
Received 0 Likes
on
0 Posts
S'Torque
It would - to shuttlecock the nose down, as would the moment of the drag from the boom, given that the rotor lift was surely sharply reduced just before that point... in the same circumstances, the hypothetical slow/stopped rotors would tend to shuttlecock it belly down.
If the circumstances were right for a sharp pitch down, then it could even establish a "tumble".
The horizontal stabiliser would still have an aerodynamic effect during a high rate of descent, rotors turning or not.
If the circumstances were right for a sharp pitch down, then it could even establish a "tumble".
Purveyor of Egg Liqueur to Lucifer
Tr,
I thought you meant they were continuing the flight profile towards base with the tail problem, intending to go straight in.
They may well have been slow, perhaps at a speed that would cause the ac to spin (appear to tumble) and if you can't get forward speed on then you are looking at twist grips.
Although we haven't heard that it was in the hover, neither have we heard that it was in forward flight. All I've read/heard in reference to flight phase is tumbling, which could be a spin in the hover or spin in forward flight. I think it's agreed that 'tumbling' wasn't the actual condition.
Perhaps continued, controlled flight wasn't possible, leaving autorotation into the city the only option.
Agreed, however where is the line between HOGE and forward flight?
How about they were at 1,000' descending 500'/min @ 70kts, pre landers and the tail goes?
In which case you would probably be at (and likely to keep?) a low power/low torque setting. Unlikely to increase power to any great extent until the bottom of the approach? (I would guess one minute out would be about one mile, and therefore about 3-400'?)
Ergo, very little torque demanded? Very little tail rotor authority required, a bit like your 40kts example.
Ergo, very little torque demanded? Very little tail rotor authority required, a bit like your 40kts example.
They may well have been slow, perhaps at a speed that would cause the ac to spin (appear to tumble) and if you can't get forward speed on then you are looking at twist grips.
Although we haven't heard that it was in the hover, neither have we heard that it was in forward flight. All I've read/heard in reference to flight phase is tumbling, which could be a spin in the hover or spin in forward flight. I think it's agreed that 'tumbling' wasn't the actual condition.
Perhaps continued, controlled flight wasn't possible, leaving autorotation into the city the only option.
Tail rotor failure in OGI hover is the only regime I can imagine that would require such extreme action,
How about they were at 1,000' descending 500'/min @ 70kts, pre landers and the tail goes?
Join Date: Jul 2000
Location: Nova
Posts: 1,242
Likes: 0
Received 0 Likes
on
0 Posts
How about they were at 1,000' descending 500'/min @ 70kts, pre landers and the tail goes?
That's exactly what you told us earlier isn't it? 70kts is flyable?
Are you saying he had/was 'going around' from an approach?
What would you do?
Purveyor of Egg Liqueur to Lucifer
What would I do?
Try to increase forward airspeed, if there was the height to do so and the fin did its part and we didn't start to spin on application of power.
Until the point at which you try to gain airspeed or get close to the ground. 20' above the ground is not the time to find out either that the wind isn't going to help you or the fenestron blade pitch isn't enough.
Try to increase forward airspeed, if there was the height to do so and the fin did its part and we didn't start to spin on application of power.
Very little tail rotor authority needed.
Purveyor of Egg Liqueur to Lucifer
Missed the edit.
That's exactly what you told us earlier isn't it? 70kts is flyable?
Are you saying he had/was 'going around' from an approach?
Are you saying he had/was 'going around' from an approach?
No, I'm not. Where did you get that from?