Max Contingency checks?
Thread Starter
Join Date: Oct 2009
Location: ipswich, UK
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Max Contingency checks?
Hi there, i am trying to find out why max contingency checks are carried out, what would cause them too fail and also what would cause a sloppy feel in the cyclic stick when carrying this out with an associated airframe vibration.
many thanks for your assistance.
many thanks for your assistance.
Avoid imitations
Join Date: Nov 2000
Location: Wandering the FIR and cyberspace often at highly unsociable times
Posts: 14,573
Received 422 Likes
on
222 Posts
The main gearbox is about to come off.
Maybe you should give us a clue as to which type you are talking about?
Max Con checks can fail for a wide variety of reasons, eg incorrect FCU limit stop, TOT limit reached before specified power reached (dirty or damaged engine), fuel flow restriction (eg carbon deposits inside delivery pipes in hot part of engine due to inadequate purging on shutdown). It is however hard to think of an engine/transmission malfunction that would cause the other effects you mention - apart from ShyTorque's hypothesis of course
HC
Max Con checks can fail for a wide variety of reasons, eg incorrect FCU limit stop, TOT limit reached before specified power reached (dirty or damaged engine), fuel flow restriction (eg carbon deposits inside delivery pipes in hot part of engine due to inadequate purging on shutdown). It is however hard to think of an engine/transmission malfunction that would cause the other effects you mention - apart from ShyTorque's hypothesis of course
HC
Join Date: Mar 2007
Location: UK
Posts: 321
Likes: 0
Received 0 Likes
on
0 Posts
Have a read of the procedure for carrying out a max contingency check on the Lynx, and look at the parameters that it asks to be set and to be recorded…and then think about why.
Basically, the check is to ensure that an engine can provide enough power, without exceeding set limits, to keep the rotor speed within a % margin to keep the helicopter in the air. A/c weight, collective pitch setting (Tq), OAT, aircraft speed and density altitude are all factors to consider.
Think.... 'a twin-engined helicopter is taking off, with little forward speed, and an engine fails. What does the good engine have to achieve?'
That's why we do max cont checks.
Think about why an engine wouldn't be running as efficiently as it should, and that should give you a few clues as to why an engine might fail its check.
Sloppy cyclic? If a helicopter starts to loose height, what does the pilot do with the collective? What affect does this have on the pitch of the rotor blades? What happens next if blades can’t produce any more lift ?
Basically, the check is to ensure that an engine can provide enough power, without exceeding set limits, to keep the rotor speed within a % margin to keep the helicopter in the air. A/c weight, collective pitch setting (Tq), OAT, aircraft speed and density altitude are all factors to consider.
Think.... 'a twin-engined helicopter is taking off, with little forward speed, and an engine fails. What does the good engine have to achieve?'
That's why we do max cont checks.
Think about why an engine wouldn't be running as efficiently as it should, and that should give you a few clues as to why an engine might fail its check.
Sloppy cyclic? If a helicopter starts to loose height, what does the pilot do with the collective? What affect does this have on the pitch of the rotor blades? What happens next if blades can’t produce any more lift ?
Last edited by nodrama; 20th Dec 2009 at 09:57.
Join Date: Apr 2009
Location: France
Age: 66
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
Hi
Not sure I have the right answer but, when carrying a max contengency check on a GEM engine, the pilot must pull up the collective to try to reach a defined Ng value, thus, usually, the Nr drops below 100% ( down to but not below 96% if I remember). During that check, the cyclic is sometimes "sloopy" due to the low RPM of the rotor...
DO
Not sure I have the right answer but, when carrying a max contengency check on a GEM engine, the pilot must pull up the collective to try to reach a defined Ng value, thus, usually, the Nr drops below 100% ( down to but not below 96% if I remember). During that check, the cyclic is sometimes "sloopy" due to the low RPM of the rotor...
DO
Below the Glidepath - not correcting
An easier route to establish the reason for Max Con checks on the Lynx is to look at the course of action if the engine fails the check - carry out a compressor wash.
On the Lynx you are confirming that max power measured as engine torque (with the engine not under test back at Ground Idle) is attainable within the parameters for Nh and T6, against measured air density (altitude) and outside air temperature. When it fails, it is usually a function of a "dirty" ECU.
Max Con checks are routinely carried out as a scheduled maintenance op, if engine power is suspect and following an ECU change.
The vibration and handling are simply because you are pulling max power and batting along at a fair rate of knots. Even on one engine, the Lynx is still pretty powerful at a couple of thousand feet. No reason for the cyclic to feel unusual other than you are likely to have it well forward associated with an arm full of collective. The Nr gets lower than usual, but it shouldn't be too low
Red Hot tip -When you are about to test the other engine always, always, put the original ECL back to Flight Idle before retarding the second one to Ground Idle, unless you wish to experience some new CWP captions.
And Mighty Gem is correct - Mick Dzedze knows more about this stuff than most people have forgotten, just give yourself lots of time to hear the answer.
On the Lynx you are confirming that max power measured as engine torque (with the engine not under test back at Ground Idle) is attainable within the parameters for Nh and T6, against measured air density (altitude) and outside air temperature. When it fails, it is usually a function of a "dirty" ECU.
Max Con checks are routinely carried out as a scheduled maintenance op, if engine power is suspect and following an ECU change.
The vibration and handling are simply because you are pulling max power and batting along at a fair rate of knots. Even on one engine, the Lynx is still pretty powerful at a couple of thousand feet. No reason for the cyclic to feel unusual other than you are likely to have it well forward associated with an arm full of collective. The Nr gets lower than usual, but it shouldn't be too low
Red Hot tip -When you are about to test the other engine always, always, put the original ECL back to Flight Idle before retarding the second one to Ground Idle, unless you wish to experience some new CWP captions.
And Mighty Gem is correct - Mick Dzedze knows more about this stuff than most people have forgotten, just give yourself lots of time to hear the answer.
The Max con check is usually completed post ECU change to ensure that the Ng governor is set correctly and the expected values of Ng/T6 can be reached without NR decay - ie that the engine is performing as advertised and therefore the performance figures from the ODM are reliable (predicted height loss/Min SELF).
If the Nr decays before the figures are reached, the Ng governor is set too low (had this on a couple of occasions).
If you get a sloppy cyclic in a Lynx, I refer you to Shy Torque's diagnosis or you have inadvertantly switched off the stick trim
If the engine fails the max con check then industrial comp wash is next followed by further max con then governor adjustment - after that it is time to phone Rolls and talk replacements.
If the Nr decays before the figures are reached, the Ng governor is set too low (had this on a couple of occasions).
If you get a sloppy cyclic in a Lynx, I refer you to Shy Torque's diagnosis or you have inadvertantly switched off the stick trim
If the engine fails the max con check then industrial comp wash is next followed by further max con then governor adjustment - after that it is time to phone Rolls and talk replacements.
Max - what is wrong with 'spectacles, testicles, wallet and watch'?
Mighty Gem - I thought there was a 'j' in Mick's surname somewhere but I can't remember where. Still an awesome scrabble score on a triple letter bonus!
Mighty Gem - I thought there was a 'j' in Mick's surname somewhere but I can't remember where. Still an awesome scrabble score on a triple letter bonus!
Join Date: Mar 2007
Location: UK
Posts: 321
Likes: 0
Received 0 Likes
on
0 Posts
You've told us before that you are studying for a Foundation Degree, so I assume the original question is part of your course.
The posts so far all indicate that a sloppy cyclic and airframe vibration isn't experienced during a max cont check on a Lynx.
That's the whole point of the question....it's theoretical...to get you to think about what would have to happen, and why, during a max cont check that would cause these things to happen.
Join Date: Sep 2007
Location: Thailand
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
Max contingency checks.
Ask a Reem says Mighty Gem.
Well when young Will joined his first Lynx equipped unit, I can honestly say I have never hears so much Sh1t talked about a subject as this one.
I was listening to guys who had been on Lynx for years telling each other what they thought they where on about and arguing quite seriously.
I was baffled.
Then I notice out Navy Chief shaking his head.
What are they on about says I ?
Hello we've not met have we?
No but
John think what you called on Scout a Topping Check.
Suddenly all was clear.
Topping Check to ensure the Gas Generator Section of the Engine (N1) will always delivers enough 'Gas' to "Spin"' the Power Turbine to it's max 100 or 100 + % as laid down in manufacturers manual.
john
Ask a Reem says Mighty Gem.
Well when young Will joined his first Lynx equipped unit, I can honestly say I have never hears so much Sh1t talked about a subject as this one.
I was listening to guys who had been on Lynx for years telling each other what they thought they where on about and arguing quite seriously.
I was baffled.
Then I notice out Navy Chief shaking his head.
What are they on about says I ?
Hello we've not met have we?
No but
John think what you called on Scout a Topping Check.
Suddenly all was clear.
Topping Check to ensure the Gas Generator Section of the Engine (N1) will always delivers enough 'Gas' to "Spin"' the Power Turbine to it's max 100 or 100 + % as laid down in manufacturers manual.
john
Join Date: Dec 2009
Location: uk
Age: 50
Posts: 69
Likes: 0
Received 0 Likes
on
0 Posts
PPI
Thought the PPI was a thorough check of both NG (compressor) and PTIT (Hot End) , that is why it is carried out at timed intervals as opposed to post maintenace or post fault. Max Con is basically fuel flow and fuel burn hence why fuel ftg stops come into play, The Max con NG and Ptit are a lot higher than PPi figures.
Join Date: Apr 2000
Location: the netherlands
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
well after having flown about 6000 hours on a lynx..with GEM.. there is no connection between a max. contingency check and sloppy cyclic and aircraft vibraton.
Max. cont checks..never fail.. you just reach a max value.. either TQ, or NH or T6.. aircraft vibration... depends on your speed and good vibration analysis. 96 % Nr with max cont. better that you check something else...
sloppy control on a lynx at 10.000 feet ... not at sea level even with max. cont.
Avoid imitations
Join Date: Nov 2000
Location: Wandering the FIR and cyberspace often at highly unsociable times
Posts: 14,573
Received 422 Likes
on
222 Posts
C'mon chaps, seriously!
Surely we are just talking about another expression for a power assurance check?
The engine is run up to max contingency to prove it can actually comply with the manufacturer's declared power output without being limited by EGT or incorrectly governed at too high an N1.
Surely we are just talking about another expression for a power assurance check?
The engine is run up to max contingency to prove it can actually comply with the manufacturer's declared power output without being limited by EGT or incorrectly governed at too high an N1.
Join Date: Mar 2007
Location: UK
Posts: 321
Likes: 0
Received 0 Likes
on
0 Posts
What was it that Jonwilly said?.....
Max contingency check is a power assurance check. It's to assure the engine can be worked at max power, keeping Nr in limits, without being limited by temperature or N1.
PPI provides a trend to monitor the condition of the engine, and bring to the attention of the operator any deterioration in it's performance. That's why you've got that page in the M700 to plot and record the figures on a graph.
I have never hears so much Sh1t talked about a subject as this one
Max contingency check is a power assurance check. It's to assure the engine can be worked at max power, keeping Nr in limits, without being limited by temperature or N1.
PPI provides a trend to monitor the condition of the engine, and bring to the attention of the operator any deterioration in it's performance. That's why you've got that page in the M700 to plot and record the figures on a graph.