engine indications
Guest
Posts: n/a
engine indications
Not sure if this is in the correct area so advise if not!
I have an aero engine for a well known light single. since overhaul it has been constantly going over the red line and will only just maintain level flight at around 50rpm below red line.
I think it is not safe to be doing this but others in the industry say its fine. However why do we have red lines painted on things (oil temp/pressure etc) if it means nothing? Surely the mountings for the engine can only take a certain torque?
Answers on a postcard please - should the aircraft be grounded?
Ta
I have an aero engine for a well known light single. since overhaul it has been constantly going over the red line and will only just maintain level flight at around 50rpm below red line.
I think it is not safe to be doing this but others in the industry say its fine. However why do we have red lines painted on things (oil temp/pressure etc) if it means nothing? Surely the mountings for the engine can only take a certain torque?
Answers on a postcard please - should the aircraft be grounded?
Ta
Could do with a little more information, really, Jelly. What aircraft is it? Is the propeller fixed pitch or controllable? Was it overhauled at the same time as the engine? Does the engine overspeed during ground running as well?
Join Date: Jun 2000
Location: The party.
Posts: 316
Likes: 0
Received 0 Likes
on
0 Posts
Alot more info req'd.
Definitly not safe if you need 50 rpm below max to maintain steady flight.
It sounds like a variable prop, was it overhauled at same time?. You need to do some instrument calibration.
Could be a number of things...................Ground it before it kills someone.
Definitly not safe if you need 50 rpm below max to maintain steady flight.
It sounds like a variable prop, was it overhauled at same time?. You need to do some instrument calibration.
Could be a number of things...................Ground it before it kills someone.
Guest
Posts: n/a
It is a fixed pitch prop. Prop has just been overhauled too and that has made no difference.
A new rpm indicator has been fitted but again no change. I could not cay about calibration but with a new instrument it seems pretty pointless?
As regards ground running - on take off roll it is upto the red line but then in climb it creeps into it and levelling off... 150 - 200 revs over the limit.
A new rpm indicator has been fitted but again no change. I could not cay about calibration but with a new instrument it seems pretty pointless?
As regards ground running - on take off roll it is upto the red line but then in climb it creeps into it and levelling off... 150 - 200 revs over the limit.
I'm suspicious of the prop. What does the maintenance organisation say about it? Is it definitely the same item (part and serial number) as was sent away for overhaul? Can they ask an owner of the same aircraft type if they can fit his/her prop for comparison purposes. Two hours labour charge at the most.
What aeroplane is it, anyway?
What aeroplane is it, anyway?
Hmmm... a bit of a mystery, to be sure. Why not contact the engine overhaul facility for their opinion? I'd suggest you get the rpm checked with a hand-held electronic prop tach first, even though the mechanical tachometer has been replaced.
I'm right out of ideas. The overhaul facility will have their test run figures on file and I think they should be your (or your AMO/employer's) next contact. You're right - the aircraft should be grounded: over-revving causes engine damage and if you're lucky it'll show up in the oil filter before the AIB get involved. It'll be expensive, either way...
Join Date: May 2006
Location: UK
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
First of all - ground it. If you superiors disagree give the CAA a call for backup. I'm sure they'll insist it be grounded.
Secondly, get on to the engine overhaul facility and get a copy of the work pack. Everything they did to that engine will be documented. Take it to an independent maintenance organisation and have them go through it and ensure everything is in order, correct parts used etc.
Limits are there for a reason - it usually is the case that it's fine to operate above those limits, but this is for a transient period only. To routinely operate above the limits is a definate no-no.
Secondly, get on to the engine overhaul facility and get a copy of the work pack. Everything they did to that engine will be documented. Take it to an independent maintenance organisation and have them go through it and ensure everything is in order, correct parts used etc.
Limits are there for a reason - it usually is the case that it's fine to operate above those limits, but this is for a transient period only. To routinely operate above the limits is a definate no-no.