[A320] Descent with V/S and speedbrake.
I want a Blue User Title
Thread Starter
Join Date: Oct 2016
Location: Winterthur
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
[A320] Descent with V/S and speedbrake.
Hello All Question:
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Question 1:
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Question 2:
What is the true meaning of "speed" mode on FMA when in V/S, it keeps the ROD but how much is the speed trend allowed to fluctuate?
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Question 1:
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Question 2:
What is the true meaning of "speed" mode on FMA when in V/S, it keeps the ROD but how much is the speed trend allowed to fluctuate?
Join Date: Sep 2016
Location: USA
Posts: 803
Likes: 0
Received 0 Likes
on
0 Posts
Hello All Question:
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Question 1:
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Join Date: Mar 2006
Location: USA
Posts: 2,523
Likes: 0
Received 0 Likes
on
0 Posts
Hello All Question:
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Question 1:
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Question 2:
What is the true meaning of "speed" mode on FMA when in V/S, it keeps the ROD but how much is the speed trend allowed to fluctuate?
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Question 1:
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Question 2:
What is the true meaning of "speed" mode on FMA when in V/S, it keeps the ROD but how much is the speed trend allowed to fluctuate?
1. If you select a high VS, the speed brakes won’t change your descent rate. They’ll just keep the speed in check if it’s still accelerating at idle.
2. Speed mode does just that, but is limited by what the engines can give you. If your VS is too high to maintain at idle thrust, it’ll simply accelerate. Take a look at the mode reversions.
Hello All Question:
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Question 1:
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Question 2:
What is the true meaning of "speed" mode on FMA when in V/S, it keeps the ROD but how much is the speed trend allowed to fluctuate?
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Question 1:
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Question 2:
What is the true meaning of "speed" mode on FMA when in V/S, it keeps the ROD but how much is the speed trend allowed to fluctuate?
First of all, you will not descend faster without the speed increasing if you use V/S instead of open descend. Either the instructor was talking about V/S giving a faster response when starting a descend, or there was some other misunderstanding/miscommunication.
1)
If you select a high V/S and the speed goes over the selected/managed speed, the speedbrakes will work. The only reason I can think of that you were told the speedbrakes are useless in V/S is in the situation that you are descending in V/S, speed is at the selected speed. Extending the speedbrakes in this situation only adds power without changing the ROD or speed.
As far as the difference between open descend versus V/S:
You stated you were descending at green dot speed, and I assume you have selected speed at green dot. In open descend, giving you a descend rate of about 800FPM. You can't really use the speedbrakes, because of the increase in VLS. If you select V/S nothing relating to the aerodynamics with the airplane changes, the speed and V/S will remain the same. If you increase the ROD by selecting a higher V/S, your speed will increase, and you could have achieved the excact same thing in open descend by selecting that higher speed. Open descend would IMO be the better mode, because if through variations in wind during the descend, your speed momentarily drops below the selected speed, in open descend the autopilot will correct that by increasing the ROD, and in V/S the autothrust will correct that by adding power.
2)
Speed (or Mach) on the FMA means the autothrust is responsible for maintaining the speed, and the autopilot is responsible for maintaining the vertical path. Possible modes for this situation are ALT, V/S, GS. In open descend the thrust is idle, in open climb the thrust is at climb power, and for both of those the autopilot pitches to keep the speed at the managed or selected speed bug.
If you climb in V/S and the speed is higher that the selected/managed speed, the autothrust will reduce power to decelerate to the selected speed. If the speed is lower, the autothrust will increase power up to climb power, to try to get to the selected speed, but it might not be able to if a high V/S is selected.
If you descend in V/S, and the speed is below the selected speed/managed, the autothrust will add up to climb power to accelerate to the selected speed. If the speed is higher than the selected/managed speed, the autothrust will reduce the thrust to try to decelerate to the selected speed, but it might not be able to if a high V/S is selected.
(not an all inclusive list of possible modes, and explanation based on AP/AT on with PL in the climb detent)
Last edited by hans brinker; 4th Jul 2022 at 03:53. Reason: spelling
Join Date: Jun 2007
Location: Wanderlust
Posts: 3,407
Likes: 0
Received 0 Likes
on
0 Posts
Hello All Question:
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Question 1:
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Question 2:
What is the true meaning of "speed" mode on FMA when in V/S, it keeps the ROD but how much is the speed trend allowed to fluctuate?
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Question 1:
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Question 2:
What is the true meaning of "speed" mode on FMA when in V/S, it keeps the ROD but how much is the speed trend allowed to fluctuate?
Only half a speed-brake
Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Yet, sometimes, you simply are right and the other guy is not.
Last edited by FlightDetent; 4th Jul 2022 at 07:22.
As a general point common between most makes of aircraft, I find the use of speedbrake with V/S a) requires more attention thus increasing workload and b) is, for most situations, unnecessary as OP DES or LVL CHG will do the job nicely and prioritise speed, leaving RoD under your control, as opposed to V/S which does the opposite.
Observing from the monitoring seat, V/S + SB on anything but a completely smooth and calm day requires constant adjustment of the SB. Fine if you have the capacity to get it right but often it loads up the monitoring pilot as well as speed wanders down to (or below) flap speed.
Observing from the monitoring seat, V/S + SB on anything but a completely smooth and calm day requires constant adjustment of the SB. Fine if you have the capacity to get it right but often it loads up the monitoring pilot as well as speed wanders down to (or below) flap speed.
Join Date: Jul 2019
Location: In the Dog Box
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
Yes, definitely no advantage going from open descent to V/S. As stated above, V/S can also be more difficult to manage because thrust is not at a fixed value in that mode.
Taking this a step further and assuming you are still in NAV mode and above the calculated vertical profile, changing from DES to OP DES will not change your descent rate either as both modes will be commanding Thrust Idle in that situation.
If you are way too high on the calculated profile and have limited use of the speed brake because of VLS margins, such as on the 321 when ATC have requested min clean speed, in my aircraft there is no shame in selecting flap early (below 20k and icing conditions permitting) which will reduce your VLS allowing for more speed brake extension. I always activate approach phase before selecting flap to prevent an embarrassing overspeed later in the arrival should managed speed be subsequently selected. Likewise there is no shame in retracting that flap later if unanticipated track miles have been added by ATC negating their continued use.
Alternatively, you could state your minimum clean speed is higher than GDot because you anticipate using speed brake to stay in touch of the calculated vertical profile, thereby handing the resulting separation management change back to ATC.
Either way, you have the opportunity to achieve a greater ROD than staying clean at GDot.
Taking this a step further and assuming you are still in NAV mode and above the calculated vertical profile, changing from DES to OP DES will not change your descent rate either as both modes will be commanding Thrust Idle in that situation.
If you are way too high on the calculated profile and have limited use of the speed brake because of VLS margins, such as on the 321 when ATC have requested min clean speed, in my aircraft there is no shame in selecting flap early (below 20k and icing conditions permitting) which will reduce your VLS allowing for more speed brake extension. I always activate approach phase before selecting flap to prevent an embarrassing overspeed later in the arrival should managed speed be subsequently selected. Likewise there is no shame in retracting that flap later if unanticipated track miles have been added by ATC negating their continued use.
Alternatively, you could state your minimum clean speed is higher than GDot because you anticipate using speed brake to stay in touch of the calculated vertical profile, thereby handing the resulting separation management change back to ATC.
Either way, you have the opportunity to achieve a greater ROD than staying clean at GDot.
Yes, definitely no advantage going from open descent to V/S. As stated above, V/S can also be more difficult to manage because thrust is not at a fixed value in that mode.
Taking this a step further and assuming you are still in NAV mode and above the calculated vertical profile, changing from DES to OP DES will not change your descent rate either as both modes will be commanding Thrust Idle in that situation.
If you are way too high on the calculated profile and have limited use of the speed brake because of VLS margins, such as on the 321 when ATC have requested min clean speed, in my aircraft there is no shame in selecting flap early (below 20k and icing conditions permitting) which will reduce your VLS allowing for more speed brake extension. I always activate approach phase before selecting flap to prevent an embarrassing overspeed later in the arrival should managed speed be subsequently selected. Likewise there is no shame in retracting that flap later if unanticipated track miles have been added by ATC negating their continued use.
Alternatively, you could state your minimum clean speed is higher than GDot because you anticipate using speed brake to stay in touch of the calculated vertical profile, thereby handing the resulting separation management change back to ATC.
Either way, you have the opportunity to achieve a greater ROD than staying clean at GDot.
Taking this a step further and assuming you are still in NAV mode and above the calculated vertical profile, changing from DES to OP DES will not change your descent rate either as both modes will be commanding Thrust Idle in that situation.
If you are way too high on the calculated profile and have limited use of the speed brake because of VLS margins, such as on the 321 when ATC have requested min clean speed, in my aircraft there is no shame in selecting flap early (below 20k and icing conditions permitting) which will reduce your VLS allowing for more speed brake extension. I always activate approach phase before selecting flap to prevent an embarrassing overspeed later in the arrival should managed speed be subsequently selected. Likewise there is no shame in retracting that flap later if unanticipated track miles have been added by ATC negating their continued use.
Alternatively, you could state your minimum clean speed is higher than GDot because you anticipate using speed brake to stay in touch of the calculated vertical profile, thereby handing the resulting separation management change back to ATC.
Either way, you have the opportunity to achieve a greater ROD than staying clean at GDot.
Descending from 10,000’ and ATC have given you a 10 mile final. Can set V/S of, for example, 2000’ a minute and then you know you will be at exactly 3,000’ at the ten mile final. Then all you have to do is manage the speed, the predictions for the level off arrow can vary wildly in Op Desc depending on aircraft state, what it’s expecting you to do with speed modes and speed brake etc.
Some would get upset about not flying the bugged speed but meh, it’s active use of modes to achieve a desired effect (idle power, exact level off point)
Join Date: Mar 2012
Location: Having a margarita on the beach
Posts: 2,423
Likes: 0
Received 0 Likes
on
0 Posts
Hello All Question:
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Question 1:
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Question 2:
What is the true meaning of "speed" mode on FMA when in V/S, it keeps the ROD but how much is the speed trend allowed to fluctuate?
Descending with OP DES and green-dot-speed gives a very shallow ROD, (less than 700FPM with a standard weight) try and use speed-brake and the VLS shoots up, even worse on 321.
Instructor once told me better to use V/S if you want to get down faster when at green-dot-speed but in some cases if selecting for example -2,000FPM at green-dot the speed trend starts to creep up.
Question 1:
When in this situation of high V/S selected and speed trend is shooting up why am I told speed-brake is useless in V/S mode? Surely if the speed is shooting up because of the high ROD speed-brake will have some effect.
Question 2:
What is the true meaning of "speed" mode on FMA when in V/S, it keeps the ROD but how much is the speed trend allowed to fluctuate?
Now if you are let’s say 30NM out and flying at Gdot because of sequencing, it will not be practical to configure so far out. At Gdot you descend approximately on a 3 degree glide path without speedbrakes but being far out you still have plenty of options in your pocket, first one asking for more track miles if it looks really tight (thumbs up to atc) and then configuring as you get closer.
To summarize: speedbrakes are brakes for speed they create drag and you can of course use them with VS to avoid the speed increase but it is not how you should aim to increase your ROD.
Join Date: Sep 2011
Location: FL390
Posts: 239
Likes: 0
Received 0 Likes
on
0 Posts
You kind of identity the problem and the solution yourself in your first paragraph: "VLS shoots up".
Speed brakes are not a switch. Extend them fractionally, let the aircraft respond, and then slowly and smoothly extend as needed. Once established in the descent you can get close to full deflection (or half with autopilot engaged).
VLS is proportional to load factor so similar care is required during the level off.
Speed brakes are not a switch. Extend them fractionally, let the aircraft respond, and then slowly and smoothly extend as needed. Once established in the descent you can get close to full deflection (or half with autopilot engaged).
VLS is proportional to load factor so similar care is required during the level off.
Join Date: Mar 2012
Location: Having a margarita on the beach
Posts: 2,423
Likes: 0
Received 0 Likes
on
0 Posts
I want a Blue User Title
Thread Starter
Join Date: Oct 2016
Location: Winterthur
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
Gentlemen, ladies, thank you all kindly for your responses. Thank you for the motivation and also great advise to consider and take onboard! I will endeavor to read each one.
Cheers!
To summarise, regardless of auto-thrust mode, use of speed-brake will result in an effect if the aircraft is beyond its speed target. (In the scenario of descent)
However to be noted that in the case of SPEED mode if the auto-thrust can not maintain a target, due to excessive V/S then reaching VLS or overspeed could occur.
Cheers!
To summarise, regardless of auto-thrust mode, use of speed-brake will result in an effect if the aircraft is beyond its speed target. (In the scenario of descent)
However to be noted that in the case of SPEED mode if the auto-thrust can not maintain a target, due to excessive V/S then reaching VLS or overspeed could occur.
Only half a speed-brake
Many times, as you will clearly see around here, people verbalise things differently. But actually do the same thing.
Surely you remember the class-room exercise where teams of 4 need to write SOP for boiling an egg (*).
Indeed, dirty wing performs worse. Fixed V/S mode targets the selected value, A/THR matches the bug. Misconfugure the three and something has to give. That you already knew.
Because you made it to the seat not by divine error but by being qualified with awareness which way is up, forward and how gravity works.
So perhaps the right thing to ask on the never-ending thorny path to proficiency is not what the instructor said but rather why he said it.
(*) in case you did not, you still can see where that is going which proves my point.
{I will be collecting the T-shirt orders from mid-month}
Surely you remember the class-room exercise where teams of 4 need to write SOP for boiling an egg (*).
Indeed, dirty wing performs worse. Fixed V/S mode targets the selected value, A/THR matches the bug. Misconfugure the three and something has to give. That you already knew.
Because you made it to the seat not by divine error but by being qualified with awareness which way is up, forward and how gravity works.
So perhaps the right thing to ask on the never-ending thorny path to proficiency is not what the instructor said but rather why he said it.
(*) in case you did not, you still can see where that is going which proves my point.
{I will be collecting the T-shirt orders from mid-month}
Last edited by FlightDetent; 5th Jul 2022 at 03:25.
I want a Blue User Title
Thread Starter
Join Date: Oct 2016
Location: Winterthur
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
Many times, as you will clearly see around here, people verbalise things differently. But actually do the same thing.
Surely you remember the class-room exercise where teams of 4 need to write SOP for boiling an egg (*).
Indeed, dirty wing performs worse. Fixed V/S mode targets the selected value, A/THR matches the bug. Misconfugure the three and something has to give. That you already knew.
Because you made it to the seat not by divine error but by being qualified with awareness which way is up, forward and how gravity works.
So perhaps the right thing to ask on the never-ending thorny path to proficiency is not what the instructor said but rather why he said it.
(*) in case you did not, you still can see where that is going which proves my point.
{I will be collecting the T-shirt orders from mid-month}
Surely you remember the class-room exercise where teams of 4 need to write SOP for boiling an egg (*).
Indeed, dirty wing performs worse. Fixed V/S mode targets the selected value, A/THR matches the bug. Misconfugure the three and something has to give. That you already knew.
Because you made it to the seat not by divine error but by being qualified with awareness which way is up, forward and how gravity works.
So perhaps the right thing to ask on the never-ending thorny path to proficiency is not what the instructor said but rather why he said it.
(*) in case you did not, you still can see where that is going which proves my point.
{I will be collecting the T-shirt orders from mid-month}
Join Date: Sep 2011
Location: FL390
Posts: 239
Likes: 0
Received 0 Likes
on
0 Posts
I am afraid it is not VLS increases only with speedbrakes extension. On the other hand V alpha prot is G dependant and will increase in turns
Join Date: Jun 2007
Location: Wanderlust
Posts: 3,407
Likes: 0
Received 0 Likes
on
0 Posts
To cut the long story short, for a given speed OP DES with available speed brake results in max ROD. However OP DES is not a recommended mode on the final approach and whatever the vertical displacement, on final approach it must be managed with SPEED/VS. If not possible a GA is the only option.
If you’re within limits, maintain OP DES and the speed, and hang some flap out. The aircraft will no longer be flying best L/D speed and your ROD will increase.
As mentioned, this would only be appropriate prior to commencing approach, and as always go around or discontinue the approach if you aren’t ready.
As mentioned, this would only be appropriate prior to commencing approach, and as always go around or discontinue the approach if you aren’t ready.
Join Date: Feb 2024
Location: JAPAN
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
speed brake vs Vls
hi there.
i have a question about speed brake and Vls.
if using full speed brake without Auto Pilot, how much increasing Vls?
i’m looking forward to your reply.
Thanks.
i have a question about speed brake and Vls.
if using full speed brake without Auto Pilot, how much increasing Vls?
i’m looking forward to your reply.
Thanks.