A320: Confusion about IDG oil and Engine oil
Thread Starter
Join Date: Jul 2006
Location: Somewhere over the rainbow
Posts: 946
Likes: 0
Received 0 Likes
on
0 Posts
A320: Confusion about IDG oil and Engine oil
Hello guys,
While reading the FCOM about the ECAM advisory conditions for the engines regarding the Oil Temperature it’s written
From what I understand: Engine has it’s own oil sytem and IDG has its own oil system and they are independent. So why the IDG oil cooling system can have an effect on the engine oil temperature?
Thank you.
While reading the FCOM about the ECAM advisory conditions for the engines regarding the Oil Temperature it’s written
”In addition, an increase in oil temperature could be related to the IDG oil cooling system. To reduce oil temperature, before limits are reached, the following are recommended:
1. Low Speed- Increase engine speed to increase fuel flow and thereby cool IDG oil.
2. High Speed- Reduce generator load or turn off generator. If the oil temperature continues to rise, mechanically disconnect the IDG.
1. Low Speed- Increase engine speed to increase fuel flow and thereby cool IDG oil.
2. High Speed- Reduce generator load or turn off generator. If the oil temperature continues to rise, mechanically disconnect the IDG.
Thank you.
To be clear, I have no information on these specific engines.
However, it would appear that the oils are fuel cooled. If the IDG got first bite at the cooling fuel flow, before the engine oil or maybe simultaneously, then this would appear to explain the statements from the books.
However, it would appear that the oils are fuel cooled. If the IDG got first bite at the cooling fuel flow, before the engine oil or maybe simultaneously, then this would appear to explain the statements from the books.
Join Date: Jan 2014
Location: N5109.2W10.5
Posts: 720
Likes: 0
Received 0 Likes
on
0 Posts
Join Date: May 2007
Location: FL390
Age: 38
Posts: 224
Likes: 0
Received 0 Likes
on
0 Posts
You are correct. DSC 70-41 Fuel System shows an oil cooing diagram with IDG cooling taking place before that warmed fuel goes to the engine oil cooler heat exchanger. See Oil cooling
However what doenst make sense here is that, in QRH for IDG oil temp >147 advisory, instructions are only to shed electrics. FF is nowhere here, but it should as a last resort? Or I guess engine oil would heat last, so you address IDG issues first with electrics.
IMO, I think we need the engine oil system diagrammatic, as for sure there is an air cooled heat exchanger (fan duct air) somewhere, mostly the exchangers shown here are primarily to raise the temperature of the fuel to prevent icing. Same goes for the IDG which will have a small amount of oil at very high pressure and hence need a lot of heat dissipation.
Join Date: Jan 2014
Location: N5109.2W10.5
Posts: 720
Likes: 0
Received 0 Likes
on
0 Posts
IMO, I think we need the engine oil system diagrammatic, as for sure there is an air cooled heat exchanger (fan duct air) somewhere, mostly the exchangers shown here are primarily to raise the temperature of the fuel to prevent icing. Same goes for the IDG which will have a small amount of oil at very high pressure and hence need a lot of heat dissipation.
FUEL/OIL HEAT EXCHANGER (FOHE)
The fuel/oil heat exchanger uses cold fuel from the Fuel Metering Unit (FMU) to cool the oil. Oil from the lubrication system enters the FOHE, via the Servo Fuel Heater (SFH) and the Air Cooling Oil Cooler (ACOC), and flows around the fuel tube in the matrix.
The FADEC controls the fuel and the engine oil temperature.
IDG COOLING
The Integrated Drive Generator (IDG) fuel/oil heat exchanger enables to cool the IDG oil.
The FADEC controls the fuel and the engine oil temperature.
Can't speak for brand A, but Boeing has used fuel/oil heat exchangers to cool the IDG oil since at least the 757/767. With the advent of FADEC, the systems have become somewhat more sophisticated (e.g. active control of the oil cooling rather than the earlier passive systems) but the fundamental systems have remained largely unchanged in the last 40 years.
Join Date: Nov 2006
Location: Tropics
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
Never quite fully understood this as well.
V2500 - Engine oil is first cooled via the Air/Oil Hear Exchanger before entering the Fuel/Oil Heat Exchanger for another round of heat exchanger. The fuel that cools the engine oil in the Fuel/Oil Heat Exchanger is part of a rather complex system (refer to FCOM diagram) where it also routed to cool the IDG oil.
Based on this I infer that if there’s something wrong with IDG leading to high IDG oil temperature, it will cause the fuel that comes through to cool it to warm up significantly enough to be inefficient to cool the engine oil effectively when it eventually reaches the Fuel/Oil Heat Exchanger. Hence the procedure to increase fuel flow if possible or reduce IDG loads.
V2500 - Engine oil is first cooled via the Air/Oil Hear Exchanger before entering the Fuel/Oil Heat Exchanger for another round of heat exchanger. The fuel that cools the engine oil in the Fuel/Oil Heat Exchanger is part of a rather complex system (refer to FCOM diagram) where it also routed to cool the IDG oil.
Based on this I infer that if there’s something wrong with IDG leading to high IDG oil temperature, it will cause the fuel that comes through to cool it to warm up significantly enough to be inefficient to cool the engine oil effectively when it eventually reaches the Fuel/Oil Heat Exchanger. Hence the procedure to increase fuel flow if possible or reduce IDG loads.