B777 V/S Mode
Thread Starter
Join Date: Nov 2009
Location: PK
Posts: 195
Likes: 0
Received 0 Likes
on
0 Posts
B777 V/S Mode
hi
looking for some write up on the following mode of B777:
Condition 1: Maintaining an altitude e.g. 1000 feet with "ALT" indicated on FMA.
The aircraft does not descent in V/S below 1000 if altitude set in MCP altitude window is 1000 or above.
Condition 2: Maintaining an altitude e.g. 1000 feet (which is also the MDA and is set as minimums on the PFD).
The aircraft descends in V/S below 1000 even though the altitude set in the MCP altitude window is 1000 or above.
Is this logic (if I am correct) mentioned any where in the Boeing manuals?
thanks
looking for some write up on the following mode of B777:
Condition 1: Maintaining an altitude e.g. 1000 feet with "ALT" indicated on FMA.
The aircraft does not descent in V/S below 1000 if altitude set in MCP altitude window is 1000 or above.
Condition 2: Maintaining an altitude e.g. 1000 feet (which is also the MDA and is set as minimums on the PFD).
The aircraft descends in V/S below 1000 even though the altitude set in the MCP altitude window is 1000 or above.
Is this logic (if I am correct) mentioned any where in the Boeing manuals?
thanks
Condition 1)- The aircraft will not leave the MCP alt in V/S. It will revert to Alt. IF the MCP is ABOVE the actual altitude, the aircraft WILL descend in V/S.
Condition 2) Not sure what you're getting at- if the aircraft descends in V/S to the altitude set in the MCP, it will capture that altitute. There is no relationship between what is set as the MDA and the behaviour of the AFDS.
Condition 2) Not sure what you're getting at- if the aircraft descends in V/S to the altitude set in the MCP, it will capture that altitute. There is no relationship between what is set as the MDA and the behaviour of the AFDS.
Thread Starter
Join Date: Nov 2009
Location: PK
Posts: 195
Likes: 0
Received 0 Likes
on
0 Posts
Thanks Wizofoz
thats what i was looking for. do you know a reference about this feature in the boeing manuals?
thanks
IF the MCP is ABOVE the actual altitude, the aircraft WILL descend in V/S
thanks
Not specifically, but it's simply that the feature works by attaining the commanded V/S until it captures the MCP alt.
If the MCP ALT is above you and you are descending, it never will, so it KEEPS descending.
It does also have over-speed and low-speed protection features.
If the MCP ALT is above you and you are descending, it never will, so it KEEPS descending.
It does also have over-speed and low-speed protection features.
Last edited by Wizofoz; 27th Sep 2012 at 07:36.
Thread Starter
Join Date: Nov 2009
Location: PK
Posts: 195
Likes: 0
Received 0 Likes
on
0 Posts
Thanks guys
Ref: 11.31.30
When the FMC is “on approach”, the following features are available:
• The MCP altitude can be set above the airplane altitude for the missed approach. When the MCP altitude setting is at least 300 feet above the current airplane altitude, VNAV continues to command a descent.
Just like the above reference I am interested in finding out where in the manuals it is written that "IF the MCP is ABOVE the actual altitude, the aircraft WILL descend in V/S".
I know it does! there is no confusion about understanding this (1000 feet was just an example to explain what I wanted to ask).
Since it is a feature, it must be mentioned somewhere like it is for the VNAV case.
Could not find it in the flight management navigation or approach procedures.
Regards
Ref: 11.31.30
When the FMC is “on approach”, the following features are available:
• The MCP altitude can be set above the airplane altitude for the missed approach. When the MCP altitude setting is at least 300 feet above the current airplane altitude, VNAV continues to command a descent.
Just like the above reference I am interested in finding out where in the manuals it is written that "IF the MCP is ABOVE the actual altitude, the aircraft WILL descend in V/S".
I know it does! there is no confusion about understanding this (1000 feet was just an example to explain what I wanted to ask).
Since it is a feature, it must be mentioned somewhere like it is for the VNAV case.
Could not find it in the flight management navigation or approach procedures.
Regards
....And as such is probably something of an omission on Boeings part, as I'm pretty sure there are other types (does the 737? It's been a while!!) that WILL fly away from the MCP Alt in V/S.
Join Date: Apr 2010
Location: Home soon
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
....And as such is probably something of an omission on Boeings part, as I'm pretty sure there are other types (does the 737? It's been a while!!) that WILL fly away from the MCP Alt in V/S.
The Aircraft is level at 5000 ft, MCP set at 5000ft.
Pilot selects VS and tries to get a descent,other pilot looks at him/her and starts laughing.
Condition2:
Aircraft is in descent in VS mode towards a lower MCP altitude,if the MCP is reset to an altitude setting higher than the aircraft actual altitude ,the VS will now be in an OPEN DeSCENt mode,therefore NO protection from the automatics.the other pilot will start yelling
Pilots proper procedures for MCP setting,calling FMa changes is the protection..(ie CDA,approaching MDA)
.
The VS needs a minimum of 100 ft mcp change to arm the mode.
Last edited by de facto; 28th Sep 2012 at 05:22.
Thread Starter
Join Date: Nov 2009
Location: PK
Posts: 195
Likes: 0
Received 0 Likes
on
0 Posts
Condition 3:
The aircraft is level at MDA and does a circle to land with higher (missed approach) altitude set in MCP. When ready to leave the MDA the pilot uses V/S to start the final descend. Other pilot neither yells nor laughs but just wonders where is this written
The aircraft is level at MDA and does a circle to land with higher (missed approach) altitude set in MCP. When ready to leave the MDA the pilot uses V/S to start the final descend. Other pilot neither yells nor laughs but just wonders where is this written
Join Date: Oct 2007
Location: Location, Location
Posts: 743
Likes: 0
Received 0 Likes
on
0 Posts
The point I was actually trying to make was that V/S is a dangerous mode to use
It should be used sensibly and monitored carefully, as should ALL modes.
Let's remember that V/S is the recommended mode for a climb in severe turbulence so it pays to practice it's effective use from time to time (such as on a CDA etc).
V/S is more correctly a transition mode between a climb/descent and a level altitude. It will take the aircraft away from an MCP ALT and it does have overspeed and low speed protection.
It is not particularly good for a CDA nor a holding pattern descent, just useful.
Never heard of V/S mode being endorsed by Boeing for climbs/descent/cruise in turbulence. Sounds like somebody's bright idea.
#W
It is not particularly good for a CDA nor a holding pattern descent, just useful.
Never heard of V/S mode being endorsed by Boeing for climbs/descent/cruise in turbulence. Sounds like somebody's bright idea.
#W
Join Date: Jan 2006
Location: US
Posts: 2,205
Likes: 0
Received 0 Likes
on
0 Posts
"It is not particularly good for a CDA nor a holding pattern descent, just useful."
Use V/S exclusively during CDA's. Every pilot I've flown with does also.
Also use it during minor altitude changes (holding patterns, 1000' altitude changes, etc)
Also use it during climb/descent when ATC says "expect higher/lower in X minutes/X miles". Rather than blasting at climb/idle power to level off and then resume the climb/descent many folks prefer the technique of reducing rate of climb/descent to avoid an unnecessary level off. "Technique only"
Use V/S exclusively during CDA's. Every pilot I've flown with does also.
Also use it during minor altitude changes (holding patterns, 1000' altitude changes, etc)
Also use it during climb/descent when ATC says "expect higher/lower in X minutes/X miles". Rather than blasting at climb/idle power to level off and then resume the climb/descent many folks prefer the technique of reducing rate of climb/descent to avoid an unnecessary level off. "Technique only"
Join Date: Apr 2010
Location: Home soon
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
. When ready to leave the MDA the pilot uses V/S to start the final descend. Other pilot neither yells nor laughs but just wonders where is this written
Never heard of V/S mode being endorsed by Boeing for climbs/descent/cruise in turbulence. Sounds like somebody's bright idea.
#W
#W
"It is not particularly good for a CDA nor a holding pattern descent, just useful."
. Rather than blasting at climb/idle power to level off and then resume the climb/descent many folks prefer the technique of reducing rate of climb/descent to avoid an unnecessary level off. "Technique only"
Join Date: Oct 2007
Location: Location, Location
Posts: 743
Likes: 0
Received 0 Likes
on
0 Posts
Never heard of V/S mode being endorsed by Boeing for climbs/descent/cruise in turbulence. Sounds like somebody's bright idea.
Neither have I.It is obviously better when entering strong turbulence to reduce the pitch by VS to lets say 500 a min while selecting the appropriate speed than going along for the ride with possibly quite high rate of climb.
"Climb, Cruise, and Descent Considerations
After takeoff, and when established in a clean climb configuration, use of
the autoflight system is recommended for flight through turbulence.
During climb and descent, use of VNAV or flight level change may result in
excessive pitch changes as the AFDS attempts to fly speed with the
elevators. Therefore, vertical speed mode (speed on autothrottles) is
recommended for climb and descent in severe turbulence.
During cruise, VNAV and altitude hold modes both fly speed on
autothrottles and can be used in turbulence."
Join Date: Oct 2007
Location: Location, Location
Posts: 743
Likes: 0
Received 0 Likes
on
0 Posts
ER- yeah.
UNLESS you are on an LNAV track and can use VNAV PTH, what OTHER mode would you use to achieve a CDA?
UNLESS you are on an LNAV track and can use VNAV PTH, what OTHER mode would you use to achieve a CDA?
Join Date: Oct 2007
Location: Location, Location
Posts: 743
Likes: 0
Received 0 Likes
on
0 Posts
Good Cat, do you have the FCTM reference for that technique?
(A/T in hold, set thrust manually ... )
Appreciate it
(A/T in hold, set thrust manually ... )
Appreciate it
FCOM 4.20.5
Autothrottle Modes
The autothrottle modes are:
• THR – The autothrottle applies thrust to maintain the vertical speed
required by the pitch mode.
• THR REF – Thrust is set to the selected thrust limit displayed on EICAS.
• IDLE – Displayed while the autothrottle moves the thrust levers to idle;
IDLE mode is followed by HOLD mode.
• HOLD – The thrust lever autothrottle servos are inhibited. The pilot can
set the thrust levers manually.
• SPD – The autothrottle maintains the selected speed displayed on the
PFD. Speed can be set by the MCP IAS/MACH selector or by the FMC,
as shown on the CDU CLIMB, CRUISE, or DESCENT page. The
autothrottle will not exceed the operating speed limits or the thrust limits
displayed on the EICAS. If only one thrust lever is engaged, "L-" or "R-"
displays in front of SPD for the engaged thrust lever.