Airbus A318 Use of the V/S to Climb
Join Date: Jul 2011
Location: USA
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
A318 P&W
Biz pilot Brazil.
Hello, just leave the airplane in managed modes throughout the climb.
If you are flying for AV Brazil or Ocenan A. I can tell you that I have flown those 318s when they were at LAN, and as a matter of fact we still operate a handfull of them. That Airframe/Engine setup is not very optimal, engines are derated big time, and it may take you up to 38 minutes to reach FL350 when you are heavy.
If you go on V/S mode you loose airspeed and once you reach your cruising altitude those engines will continue to deliver CL THR untill you reach you managed Mach speed.
The airplane is underpowered and just as heavy as an A320, believe it or not.
Regards.
Hello, just leave the airplane in managed modes throughout the climb.
If you are flying for AV Brazil or Ocenan A. I can tell you that I have flown those 318s when they were at LAN, and as a matter of fact we still operate a handfull of them. That Airframe/Engine setup is not very optimal, engines are derated big time, and it may take you up to 38 minutes to reach FL350 when you are heavy.
If you go on V/S mode you loose airspeed and once you reach your cruising altitude those engines will continue to deliver CL THR untill you reach you managed Mach speed.
The airplane is underpowered and just as heavy as an A320, believe it or not.
Regards.
Join Date: Aug 2005
Location: fl
Posts: 2,525
Likes: 0
Received 0 Likes
on
0 Posts
The first time I was descended from above the glide slope and it captured altitude because we weren't on the glide slope you will select a low altitude too to let it capture below the intercept altitude.
Join Date: Jul 2010
Location: LHR
Posts: 187
Likes: 0
Received 0 Likes
on
0 Posts
So you'd rather it captured at 100? Why not twist is up to 1000 above what you're currently at? Then it won't capture, and the other Brucey Bonus is that if you go around it'll stop the climb at something sensible (there's the catch - remember to set g/a altitude at G/S capture) rather than climbing up to 10k +
There's nothing forbidden about it but airmanship and common sense should preside here - if you are climbing at m0.8 in managed climb and get a negative v/s then go to open climb with selected speed and notch off a couple of decimals of mach. If need be take it back to green dot.
To be fair the Easy 319/320s are not bad at climbing at altitude so you probably haven't seen this performance issue.
Never had a problem myself! It sorts it self out in managed climb and so what if it takes a while or it goes negative for a short while?? If ATC ask for a higher rate say unable, never once needed to use VS at high FLs. It gets there in the end safely by its self.
If you really want to give yourself a heart attack press EXPD at FL 350 in the climb. See what hapens then...
If you really want to give yourself a heart attack press EXPD at FL 350 in the climb. See what hapens then...
Join Date: Jul 2010
Location: LHR
Posts: 187
Likes: 0
Received 0 Likes
on
0 Posts
RWU,
I wouldn't recommend coming back to green dot no, however the method is still safer than using a v/s mode which overrides speed which could result in a stall. IMO. I've not had an issue with selecting Mach in open climb and coming back one or two decimals. I have however seen speed decay when others are concentrating so hard on climbing to an altitude using V/S and I won't ever use it at high altitudes to climb.
I wouldn't recommend coming back to green dot no, however the method is still safer than using a v/s mode which overrides speed which could result in a stall. IMO. I've not had an issue with selecting Mach in open climb and coming back one or two decimals. I have however seen speed decay when others are concentrating so hard on climbing to an altitude using V/S and I won't ever use it at high altitudes to climb.
Hpbleed,
I know of instances of reducing mach to increase RoC that have ended in low speed excursions due to ALT*. Don't be too confident that OP CLB and CLB will completely save you. If setting V/S 500-1000ft/min results in a slow speed excursion then maybe the crew are not really cut out for their job.
As I said before your/our aircraft are fairly good climbers (both power and FMGS accuracy) and I have not had to use this technique at our company and I have no desire to. But there are older Airbus (old FMGS standard/underpowered) where this is a very useful technique. If you don't believe me ask any of your Captains who have flown older charter heavyweight A320/1s.
Don't even get me started with old heavy A340s where you sometimes had to descend to get the speed back to complete the climb.
Pizza Express
Don't forget to tell ATC that you are not maintaining 500fpm as per the UK AIP.
I know of instances of reducing mach to increase RoC that have ended in low speed excursions due to ALT*. Don't be too confident that OP CLB and CLB will completely save you. If setting V/S 500-1000ft/min results in a slow speed excursion then maybe the crew are not really cut out for their job.
As I said before your/our aircraft are fairly good climbers (both power and FMGS accuracy) and I have not had to use this technique at our company and I have no desire to. But there are older Airbus (old FMGS standard/underpowered) where this is a very useful technique. If you don't believe me ask any of your Captains who have flown older charter heavyweight A320/1s.
Don't even get me started with old heavy A340s where you sometimes had to descend to get the speed back to complete the climb.
It sorts it self out in managed climb and so what if it takes a while or it goes negative for a short while??
Don't forget to tell ATC that you are not maintaining 500fpm as per the UK AIP.