Airbus' intelligence report on the 787
Thread Starter
Join Date: Jun 2005
Location: UK
Posts: 135
Likes: 0
Received 0 Likes
on
0 Posts
Airbus' intelligence report on the 787
Airbus has prepared a little dodgy dossier on the 787 and what's gone wrong in it's production. The methods used are allegedly a little shady.
The story from Flight International:
http://www.flightglobal.com/blogs/fl...ons_learnt.pdf
The FlightBlogger Blog which contains a link to the document itself:
FlightBlogger - Aviation News, Commentary and Analysis
The story from Flight International:
http://www.flightglobal.com/blogs/fl...ons_learnt.pdf
The FlightBlogger Blog which contains a link to the document itself:
FlightBlogger - Aviation News, Commentary and Analysis
Guest
Posts: n/a
Airbus Dreamliner Dossier Revealed
By Jon Ostrower on December 3, 2008 4:30 PM
In addition, Airbus believes that both the General Electric GEnx-1B and Rolls Royce Trent 1000 engines are rumoured to have missed specific fuel consumption targets by 2-3% and 3-4% respectively. "We've continued to make tweaks to the engine and we will make fuel spec when we reach entry into service," GE said.
Rolls-Royce did not return calls seeking comment.
Airbus speculates that a rumoured design change to the Trent 1000 low-pressure turbine could require Dreamliner One to switch to GEnx engines.
Though, a 787 programme source confirms that Rolls-Royce compatible pylons had been recently reinstalled on Dreamliner One.
In addition, Airbus believes that both the General Electric GEnx-1B and Rolls Royce Trent 1000 engines are rumoured to have missed specific fuel consumption targets by 2-3% and 3-4% respectively. "We've continued to make tweaks to the engine and we will make fuel spec when we reach entry into service," GE said.
Rolls-Royce did not return calls seeking comment.
Airbus speculates that a rumoured design change to the Trent 1000 low-pressure turbine could require Dreamliner One to switch to GEnx engines.
Though, a 787 programme source confirms that Rolls-Royce compatible pylons had been recently reinstalled on Dreamliner One.
Guest
Posts: n/a
Will the LPT design change hold up the flt test program for the 787 ?
Will the LPT redesign lower the fuel burn ?
Will airlines have to pay for the cost to incorporate the design change into their Trent engines?
Will airlines switch engine choice to GEnx from Trents ?
Will the LPT redesign lower the fuel burn ?
Will airlines have to pay for the cost to incorporate the design change into their Trent engines?
Will airlines switch engine choice to GEnx from Trents ?
Join Date: Aug 2005
Location: Estonia
Posts: 834
Likes: 0
Received 0 Likes
on
0 Posts
both the General Electric GEnx-1B and Rolls Royce Trent 1000 engines are rumoured to have missed specific fuel consumption targets by 2-3% and 3-4% respectively.
a rumoured design change to the Trent 1000 low-pressure turbine could require Dreamliner One to switch to GEnx engines.
If yes, do Trent 1000 problems afflict the delivery date or range of Airbus 350?
Join Date: Dec 2007
Location: Planet Earth
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
It appears as if the LPT re-design will entail broader chord baldes which may mean a re-design of turbine casing which surprise surprise is a very long lead item - big risk of not making certification flt. testing.
Join Date: Nov 2007
Location: On the chopping board.
Posts: 929
Likes: 0
Received 4 Likes
on
2 Posts
After working many years on passenger aircraft, I would feel very uncomfortable flying on anything with a complete carbon firbre skin.
Especially considering the amount of hit-and-run incidents that occur to airframes by people maneuvering ground equipment. Human nature, IE; people too scared to report a mistake.
All it takes is a good bump to seriously weaken a carbon fibre material, damage that may or may-not be detected by the human eye, and then you have an accident waiting to happen.
I know more and more aircraft outer structures are being made by this material, but an entire fuselage? Come on.....
Especially considering the amount of hit-and-run incidents that occur to airframes by people maneuvering ground equipment. Human nature, IE; people too scared to report a mistake.
All it takes is a good bump to seriously weaken a carbon fibre material, damage that may or may-not be detected by the human eye, and then you have an accident waiting to happen.
I know more and more aircraft outer structures are being made by this material, but an entire fuselage? Come on.....
I hear ya..
Nothing beats properly selected Spruce and doped silk.
And bracing all around.
Two wings, just in case. None of this cantilever, crap. You look at it and you just know that it's gonna break. People tried it and it broke.
Sorry.. I'm feeling mean.
On a more serious note: with metal structures, we ended up finding methods to detect weakening of the material (fatigue cracks, and I don't know what else). Does anyone have a quick reference to what is state-of-the-art in this department for carbon composite structures? And I mean detection, not repair. The latter seems to be fairly simple, I've read.
People talk a lot about hidden delaminations as the worst thing to deal with. For this we have tapping tests.
Nothing beats properly selected Spruce and doped silk.
And bracing all around.
Two wings, just in case. None of this cantilever, crap. You look at it and you just know that it's gonna break. People tried it and it broke.
Sorry.. I'm feeling mean.
On a more serious note: with metal structures, we ended up finding methods to detect weakening of the material (fatigue cracks, and I don't know what else). Does anyone have a quick reference to what is state-of-the-art in this department for carbon composite structures? And I mean detection, not repair. The latter seems to be fairly simple, I've read.
People talk a lot about hidden delaminations as the worst thing to deal with. For this we have tapping tests.
Join Date: Nov 2007
Location: On the chopping board.
Posts: 929
Likes: 0
Received 4 Likes
on
2 Posts
You have raised a very important point BALSA MODEL. With previous aircraft structures, there was a wealth of experience in carrying out airframe inspections to look for potential failures. However, with this newer type of material, there is little experience worldwide when the time comes to start looking at these airframes. It will probably be a trial and error/learn from other people's mistakes learning curve.
Guest
Posts: n/a
The composite fuselage pressurized exec jet, the Raytheon Premier has been in service for quite some time now and has not gone poof in flight.
Pressurization cycles have not revealed any anomolies.
What life limit (if it has), does the 'goo' have that is used as the bonding agent? I suppose it is the same as or similar to the Dreamliner's 'goo'.
Pressurization cycles have not revealed any anomolies.
What life limit (if it has), does the 'goo' have that is used as the bonding agent? I suppose it is the same as or similar to the Dreamliner's 'goo'.
Join Date: Feb 2000
Location: Pacific
Posts: 731
Likes: 0
Received 0 Likes
on
0 Posts
I've got a carbon fibre airplane built in 1986 and housed outdoors in Canada and Alaska all it's life with not a sign of any problem. Easy to maintain and repair, light and super strong no corrosion, impervious to fuel and oil. Wouldn't use anything else!