Can aircraft weight themselves?
Guest
Posts: n/a
Good idea! Could be done on air pressure in the oleo, not displacement though. Displacement is dependant not only on weight,but on ambient temperature and ,of course, correct servicing in the first place.
However a system that did it on pressure over all three oleos would certainly be feasible! Don't know why it hasn't been done-probably because aircraft undercarriages are designed by engineers not pilots!!
However a system that did it on pressure over all three oleos would certainly be feasible! Don't know why it hasn't been done-probably because aircraft undercarriages are designed by engineers not pilots!!
Guest
Posts: n/a
Hi,
Some aircraft do; for instance the 747-400.
But still we use the loadsheet figures for performance calculations. Only if the difference between the systems is more then 7000kgs, we have to look into it more closely, but still then the assumption is, that the loadsheet is correct.
The a/c system even tells you the balance figures!
Static
Some aircraft do; for instance the 747-400.
But still we use the loadsheet figures for performance calculations. Only if the difference between the systems is more then 7000kgs, we have to look into it more closely, but still then the assumption is, that the loadsheet is correct.
The a/c system even tells you the balance figures!
Static
Guest
Posts: n/a
Thanks.
Until now, I had no idea that there was anything called an oleo, let alone what it was. I think that's probably healthy. (I'm still not entirely sure, but I guess it's an hydraulic shock thingy).
It's just that nobody's ever weighed me before boarding, and an A3XX full of porky SLFs would probably notice it...
R
Until now, I had no idea that there was anything called an oleo, let alone what it was. I think that's probably healthy. (I'm still not entirely sure, but I guess it's an hydraulic shock thingy).
It's just that nobody's ever weighed me before boarding, and an A3XX full of porky SLFs would probably notice it...
R
Guest
Posts: n/a
sress/strain guages on each load bearing member of the gear would probably be a better way of doing it, v. light and cheap and accurate.
Retro fit would be relatively straight forward installation wise, as there would already be a wire going into the fusealage for brake temp etc. Tricky bit would be calibrating it, as you'd have to weigh the whole airplane to get a base figure to work from, for all I know this is done anyway, but I bet working out the how the stresses (ie weight) effect the reading got from the guages would be fun, lots of fun with load bearing items at funny angles.
Retro fit would be relatively straight forward installation wise, as there would already be a wire going into the fusealage for brake temp etc. Tricky bit would be calibrating it, as you'd have to weigh the whole airplane to get a base figure to work from, for all I know this is done anyway, but I bet working out the how the stresses (ie weight) effect the reading got from the guages would be fun, lots of fun with load bearing items at funny angles.
Guest
Posts: n/a
are you sure that they weigh themselves, I'm not. Is it not that the FMC knows the weight of the a/c as set in software and just adds the weight of the fuel and then cargo/baggage is added after manually. Having done the 744 and 330/340 courses there has never been any mention of this. There used to be a c of g system on the classic that never worked but that just knew where the weight was shifting. I stand to be corrected......
[This message has been edited by spannersatcx (edited 29 November 2000).]
[This message has been edited by spannersatcx (edited 29 November 2000).]
Guest
Posts: n/a
The A320F weighs it's self when it is airborne only when slats are retracted aircraft speed is 250kts or below and the alt is 14500 or below, it does this via the FAC which takes it's inputs from fuel flow and alfa. This is memorized and updated through out the flight.
This is very relevant on the PFD as it is from this information that "coffin corner" is diplayed, even if the aircraft is a lot lighter it will cause the systems to react as if it is at the calculated weight (proctection activation)
------------------
Gravity always wins....
This is very relevant on the PFD as it is from this information that "coffin corner" is diplayed, even if the aircraft is a lot lighter it will cause the systems to react as if it is at the calculated weight (proctection activation)
------------------
Gravity always wins....
Guest
Posts: n/a
There's a challenge Schmitegobust; stick a Chartered Engineer in a 747, and an ATPL in an aircraft design office and see who screws up first.
Might just give both breeds a bit more respect for each other!
It's the sort of thing that I'll bet was either thought up by an Engineer who flies, or by a pilot with Engineering qualifications.
G
Might just give both breeds a bit more respect for each other!
It's the sort of thing that I'll bet was either thought up by an Engineer who flies, or by a pilot with Engineering qualifications.
G
Guest
Posts: n/a
Pdub, nice idea, but in my experience strain gauges tend to be better at measuring temperature than stress (OK I know about bridge circuits and the like)! But that still begs the question of how you're going to calculate the weight of the a/c from strain gauges on the undercarriage - they don't measure compression too well. A pressure transducer on the oleo would be more practical.
VTOL
VTOL
Guest
Posts: n/a
oops , I'll get me coat
Just shows you not to trust what a 2nd year engineering undergraduate says at midnight.
I imagine the temperature of the gas in the oleo could be monitered straightforwardly allowing compensation. Of course none of this gives you an inflight reading, and a bit of rain would add a fair chunk to the weight too.
Out of interest are aircraft weighed at at any maitenance checks? As I understand that light aircfaft have a habit of putting on weight throughout their lives, does the same aply to the big stuff?
Just shows you not to trust what a 2nd year engineering undergraduate says at midnight.
I imagine the temperature of the gas in the oleo could be monitered straightforwardly allowing compensation. Of course none of this gives you an inflight reading, and a bit of rain would add a fair chunk to the weight too.
Out of interest are aircraft weighed at at any maitenance checks? As I understand that light aircfaft have a habit of putting on weight throughout their lives, does the same aply to the big stuff?
Guest
Posts: n/a
For the A320 we can use the "green dot" speed (which is the single engine best lift/drag speed) to determine the gross wt. of the aircraft in flight. eg -
Green dot spd ......220 Kts
Altitude............31000 ft
From 220 subtract 11. (this is one knot for every thousand feet above fl 200) = 209.
From 209 subtract 85 (CFM), or 80 (IAE) so 209 minus 85 = 124 (CFM) then divide by 2 = 62. 62,000 kg.
This is in the FCOM.
Hope this helps.
Green dot spd ......220 Kts
Altitude............31000 ft
From 220 subtract 11. (this is one knot for every thousand feet above fl 200) = 209.
From 209 subtract 85 (CFM), or 80 (IAE) so 209 minus 85 = 124 (CFM) then divide by 2 = 62. 62,000 kg.
This is in the FCOM.
Hope this helps.
Guest
Posts: n/a
It's not uncommon to carefully position several strain gauges so that the total result can be adjusted to give a continuously correct indication. However, I think the designer would probably rather have legs with integrity, rather than be asked to strangely shape them to suit strain gauge placement (look up a "Sting" as used in wind tunnels - works well but you get some rather funny internal shapes).
I'm with the oleo pressure method - and I can't see why a temperature transducer can't be sat next to the pressure transducer. Thereafter the maths should be pretty straightforward.
There's no strict rule on weighing intervals, but I'd be surprised if many aircraft get away with less than a 5-yearly re-weigh. Balance sheets are constantly adjusted the rest of the time as equipment is added / removed and then specific loading sheets are prepared for each trip.
G
I'm with the oleo pressure method - and I can't see why a temperature transducer can't be sat next to the pressure transducer. Thereafter the maths should be pretty straightforward.
There's no strict rule on weighing intervals, but I'd be surprised if many aircraft get away with less than a 5-yearly re-weigh. Balance sheets are constantly adjusted the rest of the time as equipment is added / removed and then specific loading sheets are prepared for each trip.
G
Guest
Posts: n/a
Spanner - The 744F's I fly, all have the weight&ballance system installed. It gives you the grossweight as well as the CG.
Before leaving the gate, you punch the figures from the loadsheet into the FMC manually, and you then compare the two. Usually they're pretty close.
Moonbeam P.
Before leaving the gate, you punch the figures from the loadsheet into the FMC manually, and you then compare the two. Usually they're pretty close.
Moonbeam P.