|
787 Lightning strike issues v FAA
Looks like another cost-schedule win over safety .Sure glad FAA management backs their people - WAYYYYY back ..:ugh:
https://www.seattletimes.com/busines...tion-measures/ FAA engineers objected to Boeing’s removal of some 787 lightning protection measures Dec. 10, 2019 at 5:00 pm Updated Dec. 10, 2019 at 8:00 pm By Dominic Gates Seattle Times aerospace reporterLast spring, Federal Aviation Administration (FAA) managers approved removing a key feature of the 787 Dreamliner wing that aimed to protect it in the event of a lightning strike. Boeing’s design change, which reduces costs for the company and its airline customers, sped through despite firm objections raised by the agency’s own technical experts, who saw an increased risk of an explosion in the fuel tank inside the wing. That clash will come under scrutiny Wednesday as FAA Administrator Steve Dickson appears before a House committee examining the agency’s regulatory performance in the wake of the two Boeing 737 MAX crashes. Lightning protection on an airplane like the 787 that’s fabricated largely from carbon composites is more elaborate than on a metal aircraft. When Boeing developed the Dreamliner, it included special measures to protect the wing fuel tank. It sealed each metal fastener in the wing with an insulating cap and embedded copper foil in strips across the carbon wing skin to disperse the current from any lightning strike. ..... goes on with a few good diagrams |
The FAA initially rejected the removal of the foil from the wing on February 22, when its certification office ruled that Boeing had not shown, as regulations required, that the ignition of fuel tank vapor by a lightning strike would be “extremely improbable,” defined in this case as likely to occur no more than three times in a billion flight hours. By then Boeing had already built about 40 sets of wings without the foil. |
Without wishing to start Boeing versus Airbus debate, does the A350 have the foil in the wings?
The question is only because, if the wing construction is broadly similar and EASA / Airbus require it, that is strong evidence that the FAA should have insisted. |
With respect to FAA Administrator Steve Dickson ...
I followed two congressional hearings with him, including his confirmation hearing in congress at the time. My take from that was that he said to have a strong 'flying' CV. But responding to congress members' questions (relating to the MAX) he answered that he had no 'design engineering' and no '(design engineering) certification' experience. Possible manufacturing engineering experience was not discussed but it appears he may not have any. The other 'MAX' witnesses did not have any either by the way. Will be interesting in that light to follow the MAX certification hearing. He will surely have to lean heavily on the knowledge and experience of others. Boeing has a 'history' with fuel tank explosions. Discussions about those are still going after many years. So 'surprising' that an issue like this, either static or lightning related, is added to that. And would be 'amazing' indeed, from not only a design engineering but also a manufacturing engineering point of view, if they have indeed proceeded to build wings without solid FAA authorisation. |
Having just said that ... taking a look at the Hearing Agenda (thanks by the way @Grebe & Seattle Times for referring to that)
Start Quote Stephen Dickson, Administrator, Federal Aviation Administration, Testimony Accompanied by Earl Lawrence, Executive Director, Aircraft Certification Service, FAA, Matthew Kiefer, Member of the FAA’s Technical Advisory Board, End quote |
William E Boeing must be spinning in his grave!
|
Originally Posted by Chris2303
(Post 10637443)
William E Boeing must be spinning in his grave!
|
William E Boeing must be spinning in his grave! I forefronted technology and innovation...Why are we still using cables to control surfaces?!?!?!?! |
Originally Posted by turbidus
(Post 10637666)
Exactly!
I forefronted technology and innovation...Why are we still using cables to control surfaces?!?!?!?! And when a special EMP warhead goes off within maybe 100 miles- it will still fly |
So does the A350 have lightning protection for the wings? |
It has metallic foils embedded in the CFRP-structure.
https://www.airbus.com/newsroom/news...aluations.html page 21: https://www.fzt.haw-hamburg.de/pers/...20_A350XWB.pdf |
The sky is black with pigeons coming home to roost.
|
Originally Posted by SLF3
(Post 10638423)
The sky is black with pigeons coming home to roost.
|
Originally Posted by GlobalNav
(Post 10639245)
The sky is falling.
|
The 787 has a copper mesh embedded in the carbon fiber matrix - the wing, fuselage, pretty much everywhere. In addition - due in part to the uncertainties in the lightning characteristics of carbon fiber - they added a metallic copper foil to the inside of the wing skin. Once they had real aircraft structure to test and analyze they were better able to quantify the lightning threat. Then:
In December 2018, SAE revised the zones based on data from reports of more than 1,000 lightning strikes on aircraft. It found that the area aft of the engines — designated Zone 2 when the 787 was certified — was rarely hit, and so changed its classification to Zone 3. I worked with Tom Thorson - the FAA specialist quoted in the linked article - and he's reasonably sharp. But he's a Propulsion specialist, not a lightning specialist. I worked some aspects of lightning protection for 20 years, but my lightning knowledge was a small fraction of that what the Boeing (and FAA) lightning experts knew. I used to say - somewhat joking - that I knew enough about lightning and lightning protection to be dangerous. Based on some of the posts on this thread, it appears ignorance is even more dangerous. |
Originally Posted by tdracer
(Post 10639358)
The 787 has a copper mesh embedded in the carbon fiber matrix - the wing, fuselage, pretty much everywhere. In addition - due in part to the uncertainties in the lightning characteristics of carbon fiber - they added a metallic copper foil to the inside of the wing skin. Once they had real aircraft structure to test and analyze they were better able to quantify the lightning threat. Then:
Combined with the zone change around the engine pylon, it was determined the foil was no longer needed, that the copper mesh along with the nitrogen inerting system provided adequate protection against lightning strike. I worked with Tom Thorson - the FAA specialist quoted in the linked article - and he's reasonably sharp. But he's a Propulsion specialist, not a lightning specialist. I worked some aspects of lightning protection for 20 years, but my lightning knowledge was a small fraction of that what the Boeing (and FAA) lightning experts knew. I used to say - somewhat joking - that I knew enough about lightning and lightning protection to be dangerous. Based on some of the posts on this thread, it appears ignorance is even more dangerous. |
Originally Posted by tdracer
(Post 10639358)
The 787 has a copper mesh embedded in the carbon fiber matrix - the wing, fuselage, pretty much everywhere. In addition - due in part to the uncertainties in the lightning characteristics of carbon fiber - they added a metallic copper foil to the inside of the wing skin. Once they had real aircraft structure to test and analyze they were better able to quantify the lightning threat. Then:
Combined with the zone change around the engine pylon, it was determined the foil was no longer needed, that the copper mesh along with the nitrogen inerting system provided adequate protection against lightning strike. I worked with Tom Thorson - the FAA specialist quoted in the linked article - and he's reasonably sharp. But he's a Propulsion specialist, not a lightning specialist. I worked some aspects of lightning protection for 20 years, but my lightning knowledge was a small fraction of that what the Boeing (and FAA) lightning experts knew. I used to say - somewhat joking - that I knew enough about lightning and lightning protection to be dangerous. Based on some of the posts on this thread, it appears ignorance is even more dangerous. That and the fact Boeing produced and delivered a large number of aircraft prior to having this change approved by the Regulator/s. Personally I can see no justification for this change based on "over 1,000" lightning strikes, I would need to see a few more zeros. |
If metal foil external to the carbon fiber structure is so important, why isn't it needed on the A350? According to what Less Hair posted, they embed copper mesh - just like Boeing - no mention of external foil in the fuel tanks...
|
Originally Posted by Bend alot
(Post 10639369)
tdracer - I think the main issues are how Boeing have been getting to their determinations (how they have been classifying things - optimistically in favour of easy and cheap), that now justify review. Remember 20/20 the MAX would have been grounded, knowing what we know now.
That and the fact Boeing produced and delivered a large number of aircraft prior to having this change approved by the Regulator/s. Personally I can see no justification for this change based on "over 1,000" lightning strikes, I would need to see a few more zeros. When it comes to specialties like Lightning protection, the FAA (and EASA) have long leaned on the expertise of the airframer experts for the simple reason that the regulators lacked that same level of expertise. When I had meetings with the FAA on lightning/HIRF issues, the FAA had one person in the entire FAA who had a similar level of understanding as the Boeing experts - he was designated a 'National Resource Specialist' (I suspect he's retired by now - he was quite a bit older than me, hopefully replaced by someone of similar expertise). The FAA routinely delegated HIRF/Lightning compliance to Boeing - long before Boeing became an ODA - for the simple reason the Boeing specialist knew far more about it than the FAA people. If the FAA lightning specialist stands up and says it's not safe, I'll take notice. Tom Thorson - as I said a reasonably bright engineer - is not an lightning specialist. He covers all aspects of Propulsion and simply cannot be expected to also be a lightning specialist. Oh, and aircraft were produced - NOT DELIVERED - before it was approved. Incorporating a change in production before it's certified is quite common - so long as there is a reasonable expectation that it will in fact be certified. |
Originally Posted by tdracer
(Post 10639374)
If metal foil external to the carbon fiber structure is so important, why isn't it needed on the A350? According to what Less Hair posted, they embed copper mesh - just like Boeing - no mention of external foil in the fuel tanks...
|
| All times are GMT. The time now is 07:01. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.