737NGs have cracked 'pickle forks' after finding several in the jets.
Join Date: Sep 2019
Location: USA
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Webby737;
You are correct about Sta 740 Bulkhead in the aft area of the Fwd Cargo compartment. We would actually cut a 14" x 18" access opening in the bulkhead web to gain access to the FWD Bottle Bolt Casting when they required replacement. Most of ours were being replaced due to Corrosion. Once the Job was finished we would install a doubler over the cutout with Hi-Loks. STA 950 was also the FWD Bulkhead in the Aft Cargo compartment.
You are correct about Sta 740 Bulkhead in the aft area of the Fwd Cargo compartment. We would actually cut a 14" x 18" access opening in the bulkhead web to gain access to the FWD Bottle Bolt Casting when they required replacement. Most of ours were being replaced due to Corrosion. Once the Job was finished we would install a doubler over the cutout with Hi-Loks. STA 950 was also the FWD Bulkhead in the Aft Cargo compartment.
Moderator
its very easy to confuse a high quality casting which is painted with a forging which is painted
Join Date: Mar 2015
Location: Washington state
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
One hour seems optimistic - every day I am reminded that there is a huge difference between theory and practice. Will it be clean enough inside there to see something as subtle as a crack?
I would assume that the area or at the very least the bolt heads/tails would be covered in sealant.
Join Date: Sep 2019
Location: USA
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
The one Hour time estimate was probably written by some engineer who has never actually performed the task.
My job as a Structure AMT is to verify the Correct Part Number AND the Correct Effectivity assigned to the Aircraft that I'm installing the part on. Also verifying the Part Number on the documents that come with the Part. The part number is already determined for me in Boeing Drawings- Boeing Illustrated Parts List - Engineering Documents- Ect.
I do not have to know whether the part is a forging -casting - extrusion- ext. That is the job of Boeing and my Engineering Dept to instruct me which part to use. My job is to follow their written Instructions.
My job as a Structure AMT is to verify the Correct Part Number AND the Correct Effectivity assigned to the Aircraft that I'm installing the part on. Also verifying the Part Number on the documents that come with the Part. The part number is already determined for me in Boeing Drawings- Boeing Illustrated Parts List - Engineering Documents- Ect.
I do not have to know whether the part is a forging -casting - extrusion- ext. That is the job of Boeing and my Engineering Dept to instruct me which part to use. My job is to follow their written Instructions.
Join Date: Jan 2014
Location: Norfolk
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
In my experience, the time quoted for an inspection is purely the time it takes to inspect. It doesn't include any work required to get access to the inspection area and restoring the aircraft to a flight condition, including any functional testing.
Join Date: Mar 2007
Location: Another Planet.
Posts: 560
Likes: 0
Received 0 Likes
on
0 Posts
Costcutting Outsourcing Strikes Again Perhaps?
Is there any connection (no pun intended!) between these parts and the structural parts dating from around the millenium supplied by a sub-contractor & supposedly made using computer guided tools?
See my postings various on this topic some years ago.
These parts required hammers and/or redrilling by hand on the assembly shopfloor in order for them to fit and stimulated the report by the victimised supervisors.
Maybe Boeing Board should lock up their senior management and restart with some old engineers and some old pilots in the new fresh design department?
That’s assuming they’ve got any dosh left to pay the rent on the Nissan huts they’ll start out with on this new exciting venture?
What a sad fate for a once great and respected aeroplane manufacturer.
See my postings various on this topic some years ago.
These parts required hammers and/or redrilling by hand on the assembly shopfloor in order for them to fit and stimulated the report by the victimised supervisors.
Maybe Boeing Board should lock up their senior management and restart with some old engineers and some old pilots in the new fresh design department?
That’s assuming they’ve got any dosh left to pay the rent on the Nissan huts they’ll start out with on this new exciting venture?
What a sad fate for a once great and respected aeroplane manufacturer.
I watched a documentary on Boeing recently. There was some covert filming get in the North Carolina plant.
One employee made a very illuminating comment, when asked about the work the factory was doing, and how they were doing it.
"We're not building them to fly, we're making them to sell".
Nail on the head, I thought.
But at least the share price is up...
One employee made a very illuminating comment, when asked about the work the factory was doing, and how they were doing it.
"We're not building them to fly, we're making them to sell".
Nail on the head, I thought.
But at least the share price is up...
That had also crossed my mind - possibly a connection to the chords & components manufactured by Ducommun to new, tighter tolerances using sledgehammers & magic markers...... Tighter tolerances that were required for NG certification, but in reality didn't exist. Apparently this is the revolutionary new computerised manufacturing process in action;
Psychophysiological entity
I recall an FO correcting me when I said that the leading edges of a BAC 1-11 wing were then 'taken to another location and annealed.' He explained the difference between annealing and normalizing.
Wasn't there mention earlier in the thread about the casting of Pickle Forks? I took the answers to mean, originally they were milled from the solid, but later cast with substantial oversize and then milled down to size. I know the metal cad be recovered, but the effects on the finished casting are serious science. I'm given to understand that even the way a hole is drilled is incredibly critical; the speed and sharpness of the tip being stipulated by the boffins.
Wasn't there mention earlier in the thread about the casting of Pickle Forks? I took the answers to mean, originally they were milled from the solid, but later cast with substantial oversize and then milled down to size. I know the metal cad be recovered, but the effects on the finished casting are serious science. I'm given to understand that even the way a hole is drilled is incredibly critical; the speed and sharpness of the tip being stipulated by the boffins.
Join Date: Sep 2019
Location: leftcoast
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
I took the answers to mean, originally they were milled from the solid, but later cast with substantial oversize and then milled down to size
Its doubtful that that item was/is a casting
But why not check with a credible source ? ASK Boeing or the Vendor !
That had also crossed my mind - possibly a connection to the chords & components manufactured by Ducommun to new, tighter tolerances using sledgehammers & magic markers...... Tighter tolerances that were required for NG certification, but in reality didn't exist. Apparently this is the revolutionary new computerised manufacturing process in action;
That photo is what should be hanging around the neck of the OEM's corporate leaders, it encapsulates where the problem within the fish comes from. When the penny drops, and that gets finally acknowledged, then perhaps the OEM can get back to being a global leader.
[The worker in this photo is working on a part that was a "CNC" manufactured part... which resulted in extended maintenance inspections due to the precision of the CNC manufacturing process. The court documents indicated no CNC capability existed. The OEM's QA people were the messengers that ended up sueing WITHOUT SUCCESS for dismissal for doing their damned job. Nothing was ever done to replace these parts as far as I am aware.
Moderator
Its doubtful that that item was/is a casting
Of course, once a part is approved as a part of the type design, as said, it is not the role of subsequent technicians to necessarily understand how the part is made, and to make their own determinations as to airworthiness, other than in accordance with approved techniques and standards. Just put the right part in the plane applying the correct technique.
We all have a role to play in the safe operation of aircraft. For some of us, it may be at the beginning, specifying the manufacturing techniques and standards of quality. For others, it's maintenance or operation of the aircraft. We all have our own "areas" in which detail is important, and misunderstanding must be prevented.
Join Date: Jul 2002
Location: Ireland
Posts: 596
Likes: 0
Received 0 Likes
on
0 Posts
For those thinking that Boeing’s cavalier attitude to safety is a modern thing, these events were 20 years ago.
Join Date: Mar 2019
Location: On the Ground
Posts: 155
Likes: 0
Received 0 Likes
on
0 Posts
I recall an FO correcting me when I said that the leading edges of a BAC 1-11 wing were then 'taken to another location and annealed.' He explained the difference between annealing and normalizing.
Wasn't there mention earlier in the thread about the casting of Pickle Forks? I took the answers to mean, originally they were milled from the solid, but later cast with substantial oversize and then milled down to size. I know the metal cad be recovered, but the effects on the finished casting are serious science. I'm given to understand that even the way a hole is drilled is incredibly critical; the speed and sharpness of the tip being stipulated by the boffins.
Wasn't there mention earlier in the thread about the casting of Pickle Forks? I took the answers to mean, originally they were milled from the solid, but later cast with substantial oversize and then milled down to size. I know the metal cad be recovered, but the effects on the finished casting are serious science. I'm given to understand that even the way a hole is drilled is incredibly critical; the speed and sharpness of the tip being stipulated by the boffins.
Aha! From Waterpilot's comment (#10) above: "To increase materials efficiency, the main component of the pickle fork is now produced out of forged, restrike aluminum. Previously the part was produced from block aluminum, which generated a significant amount of scrap because the pickle fork component was cut and shaped from the block. The pickle fork forgings now arrive in the approximate shape of the component so less aluminum is scrapped. In addition, the type of aluminum previously used for the pickle fork required shipping to California for stress relieving and return back to Auburn for continued production. The current aluminum forgings do not require stress treatment."
Last edited by Takwis; 3rd Oct 2019 at 15:41.
Join Date: Nov 2000
Location: Canada
Posts: 603
Likes: 0
Received 0 Likes
on
0 Posts
FAA orders airlines to inspect dozens of Boeing 737s for structural cracks
Boeing discovered cracks on a few of its planes undergoing maintenance in China
Thomson Reuters · Posted: Oct 03, 2019 9:41 AM ET Last Updated: an hour agoThe U.S. Federal Aviation Administration said on Wednesday that aircraft operators must inspect 165 Boeing 737 NG airliners for structural cracks within seven days after the issue was found on a small number of planes.Boeing Co notified the FAA of the issue after it discovered cracks on an aircraft undergoing modifications in China. The FAA said subsequent inspections found similar cracks in a small number of additional planes. The FAA said planes with fewer flights will eventually get inspected.
The article says the The order covers a total of 1,911 U.S. registered planes. The inspections can be done visually and should require about an hour per airplane, the FAA said.
Complete story can be viewed at: https://www.cbc.ca/news/business/boeing-737-1.5307170