Go Back  PPRuNe Forums > Aircrew Forums > Rotorheads
Reload this Page >

Dust and sand?

Wikiposts
Search

Notices
Rotorheads A haven for helicopter professionals to discuss the things that affect them

Dust and sand?

Thread Tools
 
Search this Thread
 
Old 2nd September 2013 | 19:39
  #1 (permalink)  
Thread Starter
40 Countries Visited
15 Anniversary
 
Joined: Mar 2011
Posts: 518
Likes: 50
From: London/Atlanta
Dust and sand?

Obviously vision problems landing and taking off in these conditions, comments appreciated and pictures but are there maintenance requirements immediately required following either? Just curious

Last edited by nomorehelosforme; 2nd September 2013 at 19:40.
nomorehelosforme is offline  
Reply
Old 3rd September 2013 | 02:04
  #2 (permalink)  
 
Joined: Jun 2013
Posts: 181
Likes: 0
From: Thaïland
As possible, avoid Dust and sand....
BOBAKAT is offline  
Reply
Old 3rd September 2013 | 02:31
  #3 (permalink)  
15 Anniversary
 
Joined: Nov 2010
Posts: 206
Likes: 91
From: Canada
Once in a while our routine operation? If once in a while, not really a big deal. Compressor wash/rinse more often. Pop a bit of grease in all exposed bearings on the turning bits. If routine, it can drastically reduce an engines life and power checks should be done often to keep track of the inevitable downward trend.
MLHeliwrench is offline  
Reply
Old 3rd September 2013 | 02:37
  #4 (permalink)  
25 Anniversary
 
Joined: Jan 2001
Posts: 3,008
Likes: 62
From: North Queensland, Australia
Blade leading edge erosion can be a problem.

I've also had really fine dust build up and cake on solidly to the leading edge causing a bad vibration.
Arm out the window is offline  
Reply
Old 3rd September 2013 | 03:54
  #5 (permalink)  
 
Joined: Jul 2001
Posts: 1,383
Likes: 1
From: ...in view of the 'Southern Cross' ...
Mmmmm ...

Apart from the obvious ingestion issues .... keep in mind that fine dust particles can build up within oil coolers and blowers ducts and can cause some serious vibration (due out of balance) and or overheating problems.

spinwing is offline  
Reply
Old 3rd September 2013 | 10:53
  #6 (permalink)  

Avoid imitations
Community Builder
25 Anniversary
Veteran: Air Force
 
Joined: Nov 2000
Aviation Qualifications: ATPL
Posts: 15,110
Likes: 1,083
From: Wandering the FIR and cyberspace often at highly unsociable times
Carry out zero speed landings rather than hovering; obviously dust gets everywhere, as already stated, once your downwash hits it.

But one extra thing I've learned: It's very important to look after your eyes as well as your aircraft, because otherwise you might well lose your concentration, with potentially disastrous consequences!

Turn the cockpit ventilation blower outlets away from your face and turn off the blower fan before you encounter a dust cloud (if you really must do that in the first place).

Then, after you exit the dusty conditions, turn the blower fan on maximum and open the outlets, to clear the system through.

Only later turn the outlets to aim at yourself. Because if you don't, you're likely to get grit blown in your eyes, sunglasses, visor or not and you'll certainly regret that.
ShyTorque is offline  
Reply

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.