Hangar door adjustment
Thread Starter
Hangar door adjustment
Our hangar has sliding doors which run along what appears to be the apex corner of angle iron set into the concrete base. The wheels at the bottom of the doors have a vee groove around their circumference and are encased in the welded steel structure of the door frame, whilst the top of the door, or rather an extension of it, runs in the open side of a steel channel, probably with guide wheels although they can't be seen. The hangar appears to be a commercial design, has no identifying name on it, and is about 25 years old at the most. It was dismantled and moved to our club from another airfield about nine years ago.
The problem is that the one of the doors binds when being opened or shut.
As there is so much potential for expansion and contraction on a large structure (the door aperture is approx 18 metres x 2.5 metres), one would have expected some adjustment to allow for expansion/contraction and settling. From what I can see, any adjustment would have to be on the wheels at the bottom, as there is only about 6 to 12mm clearance between the top of the door and the steel channel top guide.
Have you come across anything similar, and what is the adjustment method?
The problem is that the one of the doors binds when being opened or shut.
As there is so much potential for expansion and contraction on a large structure (the door aperture is approx 18 metres x 2.5 metres), one would have expected some adjustment to allow for expansion/contraction and settling. From what I can see, any adjustment would have to be on the wheels at the bottom, as there is only about 6 to 12mm clearance between the top of the door and the steel channel top guide.
Have you come across anything similar, and what is the adjustment method?
Last edited by Mechta; 21st Apr 2018 at 07:55.
Thread Starter
Nice hangar, can stack a few gliders in there...!
If the top channel section is what I think it is, it will contain sets of 4 wheel trolleys, which roll along the inside of the channel. The metalwork is quite expensive, for 18ft of it I was quoted 250 pounds, but it does last a long time.
If you put the door in the most stiff position, there may be lock-nut adjustments that can be made to ease the binding. Hopefully that will not make the door too loose at the other end of its travel.
Best of luck..
If the top channel section is what I think it is, it will contain sets of 4 wheel trolleys, which roll along the inside of the channel. The metalwork is quite expensive, for 18ft of it I was quoted 250 pounds, but it does last a long time.
If you put the door in the most stiff position, there may be lock-nut adjustments that can be made to ease the binding. Hopefully that will not make the door too loose at the other end of its travel.
Best of luck..
Join Date: Sep 2006
Location: Scotland
Age: 84
Posts: 1,434
Likes: 0
Received 0 Likes
on
0 Posts
Sounds to me that the two runners, (top and bottom) are not parallel/straight enough/insufficient clearance. Prob not possible to adjust the bottom one by burying it deeper into set concrete, so adjust the top runner up a bit if possible at the sticky bit.
On site visual with the set up is the only way to know.
On site visual with the set up is the only way to know.
Thread Starter
Nice hangar, can stack a few gliders in there...!
If the top channel section is what I think it is, it will contain sets of 4 wheel trolleys, which roll along the inside of the channel. The metalwork is quite expensive, for 18ft of it I was quoted 250 pounds, but it does last a long time.
If you put the door in the most stiff position, there may be lock-nut adjustments that can be made to ease the binding. Hopefully that will not make the door too loose at the other end of its travel.
Best of luck..
If the top channel section is what I think it is, it will contain sets of 4 wheel trolleys, which roll along the inside of the channel. The metalwork is quite expensive, for 18ft of it I was quoted 250 pounds, but it does last a long time.
If you put the door in the most stiff position, there may be lock-nut adjustments that can be made to ease the binding. Hopefully that will not make the door too loose at the other end of its travel.
Best of luck..
What you suggest about four wheel dollies sounds likely. Its how to access them to make adjustments that's not obvious.
Crash one The channel in which the top of the door runs is part of the structure of the hangar, so raising it would not be a simple matter.
Join Date: Oct 2004
Location: mids
Age: 59
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Just watch it when you try and tinker with it.
Have something that can take the weight of the door both sides so it can't fall if it becomes unsupported.
hangar doors falling have killed before and will kill again.
Have something that can take the weight of the door both sides so it can't fall if it becomes unsupported.
hangar doors falling have killed before and will kill again.
Trolley Hangers
Products - Cannonball: building product supplier
These work very well and adjust from the top, but likely you have a different supplier.
Get a photo of the upper hardware and check out the agricultural suppliers near where the hangar was originally built.
Round track is the way to go if you have to replace the top hardware.
These work very well and adjust from the top, but likely you have a different supplier.
Get a photo of the upper hardware and check out the agricultural suppliers near where the hangar was originally built.
Round track is the way to go if you have to replace the top hardware.