Hung Start
Thread Starter
Join Date: Oct 2009
Location: Mansfield
Age: 61
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Hung Start
Could anybody out there, please explain to me what is meant by a hung start, is it when the core won`t accelerate and it overtemps?
Cheers Daz
Cheers Daz
Join Date: Jan 2004
Location: Hopewell, Nova Scotia Canada
Posts: 29
Likes: 0
Received 0 Likes
on
0 Posts
A hung start is when fuel is applied and exhaust temp is noted but the engine will not accelerate (exhaust gas temp stays low). A hot start is a rapid exhaust gas temp rise (heading for the red line) and usually a higher than normal fuel flow.
Hope that helps.
Hope that helps.
Join Date: Dec 2007
Location: In a van
Posts: 4
Likes: 0
Received 0 Likes
on
0 Posts
As Firbird correctly states 'A hung start is when fuel is applied and exhaust temp is noted but the engine will not accelerate.'
But a bit deeper - it is usually when full ignition of the fuel in the combustion chamber does not take place, normally attributed to an inop ignitor or HEIU (there are two per engine). As all the fuel is not ignited the turbines are slower to rotate which in order is slow to rotate the compressors (HP & (IP) & LP). This manifests its self as low pick up on the N1 and N2 indications in the flight deck. The engine will take longer than normal to reach self sustaining speed - if too long the engine may self abort the start but hopefully the operator will notice it and terminate the start. The starter valve will only rotate the HPC to a nominal percent (usually 40-45%) and this is usually the RPM at which the engine 'hangs' Allowing the hung start to go its distance is bad practice as once unburnt fuel is ignited it can torch back to the NGVs/ HPT causing damage.
A hung start can also be attributed to late opening of the throttle control valve which would be shown as no initial ignition followed by a sharp rise in EGT/JPT/TET.
But a bit deeper - it is usually when full ignition of the fuel in the combustion chamber does not take place, normally attributed to an inop ignitor or HEIU (there are two per engine). As all the fuel is not ignited the turbines are slower to rotate which in order is slow to rotate the compressors (HP & (IP) & LP). This manifests its self as low pick up on the N1 and N2 indications in the flight deck. The engine will take longer than normal to reach self sustaining speed - if too long the engine may self abort the start but hopefully the operator will notice it and terminate the start. The starter valve will only rotate the HPC to a nominal percent (usually 40-45%) and this is usually the RPM at which the engine 'hangs' Allowing the hung start to go its distance is bad practice as once unburnt fuel is ignited it can torch back to the NGVs/ HPT causing damage.
A hung start can also be attributed to late opening of the throttle control valve which would be shown as no initial ignition followed by a sharp rise in EGT/JPT/TET.
Join Date: Oct 1998
Location: CGK to HKG
Posts: 249
Likes: 0
Received 0 Likes
on
0 Posts
it is usually when full ignition of the fuel in the combustion chamber does not take place, normally attributed to an inop ignitor or HEIU (there are two per engine).
Combuster interconnectors or Can Annualar arrangements ensure full light off unless a rare blocked fuel nozzle.
Only one ignitor will be used during the start sequence unless a second start is being attempted.
If the first ignitor used is inop then the engine will remain at Max motoring with a lot of fuel mist seen at the exhaust.
As all the fuel is not ignited the turbines are slower to rotate which in order is slow to rotate the compressors (HP & (IP) & LP).
The engine will take longer than normal to reach self sustaining speed
If you were to let it....
The starter valve will only rotate the HPC to a nominal percent (usually 40-45%)
once unburnt fuel is ignited it can torch back to the NGVs/ HPT causing damage.
A hung start can also be attributed to late opening of the throttle control valve which would be shown as no initial ignition followed by a sharp rise in EGT/JPT/TET.
Confusion with Max motoring with no fuel and/or ignition approx 25-30% and Hung start where fuel has been ignited but HPC slows at approx 40% due to insufficient fuel flow or bleed schedule problem.
Sorry just had a bad day
TW
Thread Starter
Join Date: Oct 2009
Location: Mansfield
Age: 61
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Thanks very much for the information chaps, I just wondered as I`ve been overhauling RB 211 04 modules for the past 20 yrs, and I`ve never thought to ask the question.
Cheers Daz
Cheers Daz
Join Date: Jan 2001
Location: Dunstable, Beds UK
Posts: 545
Likes: 0
Received 0 Likes
on
0 Posts
TW
Since when would there be a partial light off?
Combuster interconnectors or Can Annualar arrangements ensure full light off unless a rare blocked fuel nozzle.
Very true when new
However the combustor and liner have a very hard life and when they erode you do not get the situation as advertised. Several AD to rework and replace the FCL ( Including one last month !) due to - wait for it !! a batch were made forn the wrong material !!
The accel shedule is very critical on start and as engine and FCU get time in sevice some of that margin decreases. A tail wind is also not helpful
for clean starts
Since when would there be a partial light off?
Combuster interconnectors or Can Annualar arrangements ensure full light off unless a rare blocked fuel nozzle.
Very true when new
However the combustor and liner have a very hard life and when they erode you do not get the situation as advertised. Several AD to rework and replace the FCL ( Including one last month !) due to - wait for it !! a batch were made forn the wrong material !!
The accel shedule is very critical on start and as engine and FCU get time in sevice some of that margin decreases. A tail wind is also not helpful
for clean starts
Registered User **
Join Date: Mar 2009
Location: USA
Age: 49
Posts: 480
Likes: 0
Received 0 Likes
on
0 Posts
The OP had the most important part of the answer in his question. The most basic answer is when the engine is unable to advance from the point of starter assist to idle as the "cores" fail to accelerate each other.
Could be a result of bleed loss, a rich or lean mixture that will not atomize well (rich could be early starter cutout) (lean could be a fuel metering issue). There are also variable stators in the compression section that could be adjusted incorrectly or lagging. Probably a combination of several factors high and hot airfields not helping much.
Could be a result of bleed loss, a rich or lean mixture that will not atomize well (rich could be early starter cutout) (lean could be a fuel metering issue). There are also variable stators in the compression section that could be adjusted incorrectly or lagging. Probably a combination of several factors high and hot airfields not helping much.