Speed flown after Drifting down?
So,In a turbojet aircraft, after an engine failure in cruise, we hold the altitude till we get to the Vmd and then maintain the Vmd till the thrust from the remaining engine is enough to balance the drag. This gives us the minimum angle of descent. what does it mean by enough to balance the drag? is it that we want to maintain Vmd for cruise at the lower altitude also? or is it descended to a lower altitude where we can maintain LRC? If LRC then, Since after an engine failure, the most important aspect is range(i think), then why LRC? it does give 1 percent reduction in range...what speed is actually to be flown after an engine failure and why?
|
If there is no obstacle problem you descend at .78/300kts.(or whatever for the aircraft type) at fixed thrust at MCT to OEI LRC altitude and then cruise at OEI LRC cruise speed. LRC gives you the range. If you have obstacles below you then reduce speed to best L/D ratio and descend at that speed till obstacles are cleared then descend to OEI LRC cruise altitude and follow the same procedure.
|
Ddriver, good work on asking when you are not sure.
This subject is sometimes poorly understood even by people flying airliners. A common mistake is to think that the speeds used to determine the 'EDTO area of operations' is the speed that you should fly at. This is not the case at all. In the 737's that I fly the OEI speed that is used to calculate the maximum diversion distance is M0.79/310kts and that gives an area of operations of 825nm for 120min EDTO. Quite a few pilots I fly with think that they should fly these speeds if they lose an engine in the cruise. That is not the case. There is nothing to stop you flying those speeds if they are what you deem appropriate in the circumstances as the EDTO diversion fuel is calculated using those speeds, but it is up to you and your Captain or First Officer ( ultimately the Captain) to decide on what speeds are most appropriate at the time. Is it most appropriate to descend at Vmd? If you are trying to maintain altitude due terrain or traffic then probably yes. Is it most appropriate to descend at M0.79/310kts? If you need to get on the ground ASAP due fire or critically injured pax etc probably yes, but take into account the new altitude you will have to be at. Will it put you in icing or a front? Is it most appropriate to descend at an intermediate speed and transition into LRC? If you want a margin ( to stall and over speed)due to turbulence and to arrive overhead with more fuel in the tanks then probably yes. You can see from the above scenarios that each situation is different and requires thought. It is a good idea to think prior to the situation developing. For example, if you are making an ocean crossing there is a good chance you can rule out descending at Vmd and just use your current Mach number into the IAS for LRC if no traffic is about. we hold the altitude till we get to the Vmd Know what your actions will be when you see an engine roll back. Know roughly ( within ten knots) what your OEI LRC speed will be and exactly what your Vmd is. Be careful to do your own research rather than relying solely on what one Captain or Check Captain tells you as the advice given is not always of the standard it could be. Ask several trusted people. I think your question is a very good first post. Framer |
WHY LRC NOT Vmd(MRC)?
thanks for the inputs vilas and framer but the question remains why LRC and not Vmd. I understand different scenarios demand different speeds altitudes etc. But my main concern is all the checklists I hv recntly referred to mention selcting LRC for engine out cruise. I wish to know why LRC and not Vmd(MRC)which is the ideal speed for maximum range...does it have something to do with the fact that LRC gives 4 % higher speed over MRC and thereby reducing the time penalty?? which also brings to mind how EDTO states time limits from landing area and not range?? what is the role of time in all this??
|
M LRC is slightly faster than MMR and gives 99% specific range of MMR but 1% loss in range is almost recovered by the higher speed. Non ETOPS aircrafts are restricted to 60Mts. operation with OEI. That is where LRC speed helps.
|
Villas,
Is the threshold time 30 Mts or 60 Mts? |
My mistake. I meant 60 mts.
|
At MRC you are speed-unstable, which is why it is preferable to fly LRC. Nice explanation here: MRC And LRC — Tech Ops Forum | Airliners.net
|
Some confusion on this thread as to what MRC is on a Jet.
Max range is aprox 1.32 VMD and you certainly are not at the bottom of the drag (power required) curve. For any drift down the first priority is not hitting the ground. The best way to achieve that is to fly at the speed which gives you the lowest vertical speed. Once you are sure the ground is not an issue then you can think about changing strategy to arrive at your new destination either as quickly as possible or with as much remaining fuel as possible. The speed to achieve either will be decided by your current and future altitude and mass. |
...what does it mean by enough to balance the drag? Once you have levelled off, you have to decide what you want to do next. If terrain clearance allows, you now have to consider where you wish to go. If it you choose somewhere close by, you might even be too high! But if flying a long distance, an appropriate speed has to be chosen and if fuel is a problem, the speed to pick will the one that gives the best ground distance per kilo. Almost certainly that speed will entail flying at an airspeed higher airspeed than Vmd meaning that your aircraft will again descend as you accelerate to this speed. Again, the descent will be arrested as the thrust equals the drag resulting from flying at this new, higher airspeed. Assuming you have compliant ATC, it might be worth trying to "block off" some sky ahead of you, say from 1,000' beneath to 3-4,000' above you level and allow the aircraft to slowly climb as it gets lighter. It will also give a margin should temperature fluctuations and turbulence change your performance. PM |
The best way to achieve that is to fly at the speed which gives you the lowest vertical speed. The above assumes no traffic on TCAS. |
Max range is aprox 1.32 VMD and you certainly are not at the bottom of the drag (power required) curve. TAS was 440kts Mach was 0.72 Using the 1.32 you gave gives us an approximate MRC of either 311 kts IAS or Mach 0.95 which are obviously incorrect. I am not particularly knowledgable regarding jet aerodynamics so I would like to know if I have missed something or if your statement is incorrect. Can you help me there? Thank you. |
maximum range speed (jet) [Archive] - PPRuNe Forums
What was your level off altitude? What was LRC at your level off altitude? And why do you think drift down speed is Vmd? At high alt wave drag starts to negate the 1.32 rule in modern jets but not so much at lower alts. You need to look at the single eng holding speed at bottom of descent and MRC at the same alt. Less likely to be above Mcrit and below MDD. http://www.theairlinepilots.com/foru.../totaldrag.jpg so to add a little flesh. on a small jet I know well. Drift down speed at 46 T = 209kt (best L/D) Level off alt at 209Kt = 21800kg gross Level off weight @ 44T Max alt single eng LRC 44T = 15000 LRC 44T at FL150 = 254 Holding speed at FL150 44T = 192 1.32* 192 = 253.44 |
Thanks for the reply FE Hoppy.
What was your level off altitude? What was LRC at your level off altitude? And why do you think drift down speed is Vmd To try and tie in some figures with the ones you provided below I'l provide figures from the 737-800 manuals we use. At FL200 and 65T s/e hold speed is 222kts At FL200 and 65T the 2 eng hold speed is also 222 kts So using the graph you provided above, LRC should be 222x1.37= 304kts and MRC should be 222x 1.32 = 293kts. Both of those figures are a long way off. From the Boeing charts LRC under the same conditions is 267kts at FL200. So what I am thinking is that the chart you reproduced above can be relied upon for some aircraft types and not others, or for some altitudes and not others. Either that or I have a fundamental misunderstanding of what the graph is saying. More of your thoughts would be appreciated ( I just might learn something ) Thanks again, 73qanda |
Did you also read the thread I linked?
The chart is generic and typical of those used for ATPL theory. |
Rather intrigued
All,
I'm quite intrigued by this thread. Although not current, I am multi piston rated. I think what interests me here is the science behind what's going on. As a physicict, I like it when the real world works the way science class tells you it should - drifting down on one engine until equilibrium is reached, but I never thought about the airplane climbing as it gets lighter (I knew that's what Comet did back in the day of inefficient turbojets). As I read the practical suggestiong of asking for an altitude block, I was perplexed because I was focused on "drift down," and why would you need blocked altitude at equilibrium? A mental speed bumb later I realized it was for the possible climb. [One of the things I like about PPRUNE is the combination of technical AND practical information.] Big jets are way outside of my experience. The biggest thing I've flown from start up to shutdown is a Piper Navajo. I know fuel consumption is dependent on altitude and setting. What happens to total fuel consumption and range when flying on one engine at full power and lower altitude when compared to two engines at cruise power at cruise altitude? I know drag decreases with slower speed, but what is the net result? Thanks! Terry |
FE Hoppy, I have just read the thread you linked now and that answered my question. Old Smokey has it sorted.
Thus, whilst the 1.32 Vmd 'rule' is a good approximation at lower levels, it becomes redundant at typical cruise levels for jet aircraft. |
BUT WHY default is LRC and not Vmd?
well thnx @piltdown tht ws helpful...@vilas that is precisely my query why not Vmd which gives the "maximum" range. Why is default speed LRC not MRC? as range is the worst affected flight parameter after an engine failure...any other deviation called for by the peculiarities of specific contingencies could then have been accounted for from thereon( i.e.from MRC)...also why is max distance from adequate aerodrome in terms of time not distance? whts the role of time here?
|
also why is max distance from adequate aerodrome in terms of time not distance? whts the role of time here? |
vilas that is precisely my query why not Vmd which gives the "maximum" range. Why is default speed LR |
All times are GMT. The time now is 09:29. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.