Lyman,

On takeoff, there was a crosswind from the right at 19 knots, gusting to 28 knots. It lifted off in a slight left-wing down attitude. A right-wing aileron and subsequent rudder application brought the wings to level and the plane on proper heading in the crosswind. However, with the loss of the engine and pylon structure, the aircraft cg shifted aft 2%. With all slats extended the stall speed was 124 KIAS . The asymmetric slat retracted left wing stall speed was 159 KIAS, that being the speed in which directional control could be maintained. At KISA lower than 159, a stall warning shortly after liftoff would have occurred had it been electrically powered.

In a SIM setup to duplicate the conditions of failure, thirteen pilots did 70 takeoffs and 2 landings. They had been briefed, of course, on the flight ahead of their SIM exercise. When the pilots exactly duplicated the flight controls and pitch attitudes of AA 191, the aircraft was lost. However, most pilots recognized that the start of the roll left was actually a stall and lowered the nose to gain speed, recovered and continued flight. Landings were not a problem. 80% right rudder and 70% right-wing down aileron and nose down from the 14º climb attitude was required for successful recovery.

At the altitude they were at (about 300 feet), cutting back the power on the two operating engines would have been not the thing to do, they needed more forward speed.

As for the pylon maintenance, the (to be AA 191) aircraft was in for a service bulletin to replace the aft bulkhead spherical bearing. The pylons were suppose to be removed in accordance with the procedures defined in the DC-10 Maintenance Manual (engine first, then the pylon from the wing). However, American had been experimenting with the use of a forklift to remove the engine and pylon from the wing at the same time to avoid a number of electric and hydraulic disconnects. American contacted McDonnell Douglas regarding this procedure and was advised against it due to potential damage to the wing/pylon mounts. They had performed this one step operation on several (4) foreign DC-10 they were servicing. On the aircraft in question (AA 191's), they started the removal process towards the end of a work shift and left the forklift running for the next shift to finish the removal procedure. When that crew came in they had trouble removing the forward bulkhead bearings and then notice the whole engine stand was mis-aligned. The stand was then moved forward about 12 inches to enable removal of the forward bulkhead bearings. Sadly, the whole procedure was done out of sequence from what it should have been. Because of this, the aft upper flange was damaged, not only on this aircraft, but also at other US airlines which used a similar forklift procedures on 76 engine/pylons combinations. I think fatigue cracks were found on 17 engine/pylons. Damage to the aft upper flange lead to fatigue cracks being initiated. The damage was not reported because it was thought the damage was to a low stress component and was a minor repair situation at best as defined by the FAA at that time.

TD What a blessing to have you here. I think I did read losing some power on the right, in concert with lowering the nose may have been successful. I had forgotten the cross, that can't be good. Much was made of the invisibility of the leading edge, and engine, and the fact in this case losing an engine on T/O meant exactly that.

Thank you greatly for the follow up.

The a/c was badly treated, likely because knuckleheads were unquestioned. The BOSS kind of dynamic is fading away, in favor of checklists, and teams. I am not confident of out-sourcing, but sometimes.......

be well

We, then, etc. and press
 

:ok:

Our agenda to (always) be: Air Safety (for future, possible cases) in order to: low probability to occur again.

Each incident requires different inputs, the DC10 may have been saved by not lowering speed to V2, the AF case needed pilots who could handle UAS without pulling up into a full stall. It is difficult to train common sense into pilots from a training program, they have to learn it through experience with dealing with a lot of situations they learn to handle. That is what makes a seasoned pilot.

If the stall speeds with LED's retracted were above V2+15 I think the pilots would have lowered the nose to stay wings level. The big spread of speeds seems excessive to me. Unfortunately the low airspeed caused the DC10 to stall and crash.

BEA choice
 

@philip2412 and jcjeant (Thread 8 AF447)

Like you, I find these sentences in the CVR are nonsenses.

So I no more trust the CVR mistraduction.

Interesting, flying my first light twin - many moons ago - the instructor suggested that more people had been killed due to the assymetric issues of losing an engine in take-off, then had by losing the sole engine on a single under similar circumstances, and suggested that in that event one might consider closing the throttle on the remaining good engine and land straight ahead, just like a single.

Just a thought.

I heard that too, but for a twin..... With a "middle" engine, the DC10 had ample thrust, and lowering the nose with a concomitant and measured reduction in number three's thrust was a scenario that was tossed around.....

But I don't think it was meant as a prelude to a straight ahead emergency landing.

Agreed, just a comment about asymmetrical power effects.

hello sir. Thanks. The DC10 has a quirky asym layout, yes? with OEI, the #2 engine, if it is running, wants to push the nose down, its mount well above the Longitudinal axis? With #1 gone, (literally), the a/c will tuck the nose and roll left. In AA's manuals, the protocol for OEI must include this tendency? If #2 is the lost one, the a/c will Pitch up, and without a yaw, more or less?

At handover, the rumor was that the rudder pedals were inconsistent, aggravating the tendency to roll left whilst the Left wing was Stalling?

cheers

everynowandthen
That has been posted many times, are you trying to point out that I may have strayed off thread? That you may be suggesting a return to the topic? If so, I make the link as 'handover', "rolling", "emergency", "Stall", CRM, and command under stress, and more......

Both flights were STALLED, and Roll was the salient issue in LOC; There was discussion re: the DC10's handover, and the problems it may have precipitated in recovery from a rolling issue, and location of the handling pilot. Seat bias played an important "Role" in both crashes, and from similarities come differences, and instruction.