Extinguishing aircraft wheel and brake fires
Please can anyone give me a link to the regulation authorising or recommending water mist as a brake/wheel fire extinguishant?
Dick |
I'm assuming....
I'm assuming that you question the wisdom of such an act,
thereby asking for a reference to an authoritative document prescribing the use of water on a brake fire. I cannot help you, as I've always been taught to NEVER use water on a brake fire. Instead, dry chemical is what we should use. Actually, I'm thinking dry chemical is the only approved fire retardant that is approved for this....but, not being a trained fire fighter, I could quite likely be wrong. Fly safe, PantLoad |
Hi PantLoad,
Actually, it's the other way round. The JAR ATPL syllabus implies that water mist is acceptable and this has been challenged by a firefighter. I have found references to new type water mist systems that the manufactures say will be ok, and in the search for truth I would like to find a CAA or FAA document covering this. I've spent some time searching, but no luck yet Dick |
In case of hot brakes without fire, the best option is natural cooling, possibly assisted by a fan.
Here are some reference documents about the use of water mist when a wheel assembly fire develops as a consequence of hot brakes. ICAO DOC 9137-AN/898 Airport Services Manual Part 1 - Rescue and Fire Fighting 3rd Edition - 1990 12.2.3 Hot brakes and wheel fires. The heating of aircraft wheels and tires presents a potential explosion hazard, greatly increased when fire is present. In order not to endanger the members of the airport rescue and fire fighting service needlessly, it is important to distinguish between hot brakes and brake fires. Hot brakes will normally cool by themselves without the use of an extinguishing agent. Most aircraft operating manuals for propeller driven aircraft recommend that flight crew members keep the propeller forward of the fire turning fast enough to provide an ample cooling airflow. Most wheels of jet aircraft have fusible plugs which will melt at about 177°C and deflate the tire before dangerous pressures are reached. When responding to a wheel fire, airport rescue and fire fighting members should approach the wheels with extreme caution in a fore or aft direction, never from the side in line with the axle. Since the heat is transferred to the wheel from the brake it is essential that the extinguishing agent be applied to this area. If further cooling is desired after extinguishment of the fire, the agent should be directed at the brake area only. 12.2.4 Too rapid cooling of a hot wheel, especially if localized, may cause explosive failure of the wheel. Solid streams of water should not be used except as a last resort. Water fog can be used but intermittent application of short bursts of 5 to 10 seconds every 30 seconds is recommended. Dry chemical has limited cooling capacity but is an effective extinguishing agent. Once the tires are deflated, any extinguishing agent may be safely used as there is no further danger of explosion. Home Office - London HMSO, 12/99. Crown copyright 1999 ISBN 0-11-341192-8; 0113411928 5.4.2 Brake and wheel fires The overheating of brake and wheel assemblies usually follows excessive braking. This can happen on landing when a hydraulic failure reduces the ability of the pilot to utilise control surfaces (flaps) and he feels the aircraft may over run the runway or more often, on an aborted take-off. Quite often tyres will burst or, as the aircraft comes to a standstill, ignite by transference of heat from the brakes. To avoid metal failure, firefighters attending overheated brake and wheel assemblies should usually refrain from applying water and allow natural cooling. If there is fire however, a fine water fog applied from fore and aft of the undercarriage assembly is generally used. NATOPS U.S. NAVY AIRCRAFT FIREFIGHTING AND RESCUE MANUAL 15 OCTOBER 2003 6.6.1 Wheel Assembly Fires. 3. The following warnings, caution, and note pertain to all aspects of wheel assembly firefighting operations:
The FAA Aircraft Rescue and Firefighter Training CBT states that "Hot brakes should be allowed to cool naturally. If wheel grease or tires start to catch fire, use water to cool and extinguish the fire". Boeing even suggests using water mist also to cool hot brakes and plenty of water in case of a wheel assembly fire. See the note on the bottom-right corner of page 1 in each of the crash charts available here: site:www.boeing.com arff "water mist" - Google Search |
One day, at Dubai on my turnround, parked next to a very large Russian transport jet I saw the engineer throw two buckets of water over the left outboard wheel.
No joke. |
Thank you...
Dick and Aerolearner,
Thank you for the information.... I learned a lot. Fly safe, PantLoad |
When I was a trainee erk at RAF Halton way back in the last century, we were taught that Dry Powder was the only acceptable extinguishent for a brake fire and that CO2 would cause a massive explosion due to the rapid cooling effect. :=
Later in life I saw an RAF Phantom's brake fire being put out with the afore mentioned unacceptable CO2 by the guy doing so blasting the stuff onto the concrete and letting it drifted downwind over the fire. :D It was unusual for the brakes to catch fire, usually just smoking after a wheel change due to excessive grease being applied.:ugh: TTFN Howie |
All times are GMT. The time now is 13:20. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.