737 QRH checklist symbol
The older checklists had this particular symbol "< >" when a circuit breaker had to be pulled by the flight crew during a non-normal situatuon.This symbol was after the name of the checklist.The last few revisions have it for a number of checklists where there is no circuit breaker to be pulled(Mainly in a number of checklists in the hydraulics,flight controls and landing gear).
|
Don't know where you got your checklist, but this symbol does not appear in the Boeing QRH, if cct breakers need pulling, it gives you the panel no and breaker no, that's all.
|
I recall such a notation in a third party mnagement guide.
|
can you be more specific, in what NNC you found that sign?
I don't have it and don't remember having a check that instructed us to pull a CB on our qrh.. I maybe wrong though.. |
I don't have it and don't remember having a check that instructed us to pull a CB on our qrh I too cannot recall the <> symbol, but could it mark text etc removed by an amendment? |
The specific checklist has been altered by the airline.
|
Yes I assume the checklist is airline modified but cant seem to get any response to the reason for the symbol.This is what some of the checklists look like.
LOSS OF SYSTEM A <>...................................13.2 LOSS OF SYSTEM B <>...................................13.5 MANUAL REVERSION or LOSS OF SYSTEM A AND SYSTEM B <> .......................................... 737 Flight Crew Operations Manual Non-Normal Checklists Chapter NNC Flight Controls Section 9 Table of Contents Elevator Tab Limit Cycle Oscillation ..............9.1 Runaway Stabilizer <> .................................9.2 NNC. 3 All Flaps Up Landing <>....................................9.4 |
Forget it, chuck it away and get a proper Boeing QRH , the fisrt item:
Elevator Tab Limit Cycle Oscillation ..............9.1 is not even a check list item, it comes from the Boeing Study Guide Limitations. |
The above checklist was a "cut and paste" from my boeing approved QRH.Its the real deal.Its there on all our 737's.All 60 of them so am not sure how you can say its not the real thing.Like I said it is company specific but do other operators have this on their checklist.
|
" Boeing approved".. Ok, I am not suggesting this does not exist, but.. revision in 2008 is the current format. I have just checked 5 operator QRHs, none have these < > symbols. If you tell me the revision number I will get a definative answer from Boeing, from the point of view of the item 9.1, I cannot find that in ANY 737 checklist back to 2001 which is when my records cease. If you are operating in Eastern Europe then this is another complication as some checklists were sourced through 3rd parties
|
Our last revision of the QRH was in Sep 2010. The Elevator Tab Vibrations [Pg 9.6] Checklist was introduced as part of that revision.
I also have a copy of an older version of the QRH [Yellow pages] dated Sep 2003. In it there is a Memory Item checklist called Elevator Tab Limit Cycle Oscillation [Pg 9.3] The contents of the two are very similar except that the Elevator Tab Limit Cycle Oscillation checklist has a speed limit of 270 KIAS. Hope this helps |
The checklist will incorporate this according to the line no of the airframe and the SB status, that is why it appears in your revision and not all revisions, having said that, it is in Revision 17 onwards.
The symbol <> is still a mystery! This was the original question. Just for info about the SB: TAB LIMIT CYCLE OSCILLATION The following procedures are applicable to all Model 737- 600/700/700C/800 airplanes prior to the incorporation of Boeing Service Bulletin 737-55A1080, or the production equivalent, incorporating stiffened elevator tabs. An elevator tab Limit Cycle Oscillation (LCO) will be characterized by a high frequency, possible severe vibration, originating in the tail of the airplane, and emanating forward through the airframe structure. LCO events have previously occurred at airspeeds greater than 275 KIAS, and in an altitude range between 10,000 and 25,000 feet following ground deicing/anti-icing of the horizontal stabilizer. This vibration may, or may not, be felt in the control column. Cabin crew may be able to confirm the source of any airframe vibrations. If LCO is suspected in flight, immediately reduce airspeed (WITHOUT use of speed brakes, or changing aircraft configuration) to 270 KIAS, or until the vibration ceases, whichever indicated airspeed is lower. DO NOT USE SPEED BRAKES FOR THE REMAINDER OF THE FLIGHT Use of the speed brakes in other emergencies is at the discretion of the flight crew. Remain at or below the indicated airspeed at which the vibration ceased for the remainder of the flight, but do not exceed 270 KIAS. Evaluate the need to land at the nearest practicable airport. Landing airport selection should be based upon consideration of all pertinent factors such as: weather, distance to destination, range available at the reduced airspeed, maximum landing weight, and possible airframe damage. Use of ground spoilers during landing rollout is permitted. |
My QRH does indeed have these symbols( < > ), and they indicate which checklist is to be done in regard to aircraft serial number. As an example, the speed brake do not arm checklist differs depending on what aircraft number you are talking about.
|
The revision is no 25.I also thought about it being aircraft specific but its there on checklists such as ditching and runaway stabilizer.
Avenger....The elevator tab limit cycle oscillation checklist has been a memory item in my airline for the last eight years.Some operators would want a checklist as a recall item. The "< >" symbol is there in the checklist index(unannunciated,alphabetical) as well. Any thoughts?? :confused::confused: |
No mystery
eg Runway Stabilizer < >
Boeings explanation is in the FCOM: Special Note < XXX > This FCOM contains information which has been included at the request of XXX. for airplanes covered by this manual. This information may differ from Boeing recommended information. By including this information in the manual, Boeing is providing a publishing service only and such inclusion does not imply that The Boeing Company in any way endorses or approves such information. The technical accuracy and validity of all such airline provided information, and its effect, if any, on other portions of this manual, is the sole responsibility of XXX. |
Only problem is that Analyser does not mention any 'XXX' between the <> :confused:
Round again? |
Well I have tried to look(5 times and counting) but no information in the checklist instruction or legend sections.Also as BOAC mentioned that no information has been given between the "< >" symbols pertaining that its operator specific.
Does it mean that the entire checklist is operator specific?? Thanks for the help but am not sure how to get around this one |
XXX you put in the ICAO designator eg EIN = Aer Lingus and that was only for the explaination paragraph from the FCOM.
Take 2 examples from my company QRH. 'Engine control' and 'Engine Failure or Shutdown' In the index on chapter 7 it looks like this: ENGINE CONTROL...........................7.15 Engine Failure or Shutdown <>.........7.16 The titles look exactly the same on their respective pages. ENGINE CONTROL Engine Failure or Shutdown <> The Engine Control checklist has not been ammended by my company nor have they asked for any company notes or adjustments to be made to it. However the Engine Failure or Shutdown checklist has been ammended by my company and Boeing have put the <> brackets there to show this. |
Super... Thanks :)
|
All times are GMT. The time now is 07:56. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.