Go Back  PPRuNe Forums > Flight Deck Forums > Tech Log
Reload this Page >

Selected Speeds on A320

Tech Log The very best in practical technical discussion on the web

Selected Speeds on A320

Old 5th Oct 2017, 15:54
  #1 (permalink)  
Thread Starter
 
Join Date: Aug 2001
Location: Above the Horizon
Posts: 124
Likes: 0
Received 0 Likes on 0 Posts
Selected Speeds on A320

Why is it that even the VApp is SELECTED in case of failures like Dual hydraulic and Slats/Flaps jammed in the A320.
Boyington is offline  
Old 5th Oct 2017, 17:17
  #2 (permalink)  
 
Join Date: Sep 2009
Location: n/a
Posts: 56
Likes: 0
Received 0 Likes on 0 Posts
I'm only speculating here, but it could be due to the fact of being a high workload situation for the pilot flying, in such case a fixed selected speed is less workload than following a managed target affected by GS MINI.
fpuentegomez is offline  
Old 5th Oct 2017, 17:20
  #3 (permalink)  
 
Join Date: Aug 2008
Location: Betwixt and between
Posts: 666
Likes: 0
Received 0 Likes on 0 Posts
To reduce speed, sometimes below maneuvering speed to avoid over speed,or to only reduce speed once the flap is extended and to ensure minimum speeds are maintained when going around or diverting.
Sciolistes is offline  
Old 5th Oct 2017, 20:46
  #4 (permalink)  
 
Join Date: Jun 2014
Location: Mordor
Posts: 335
Likes: 0
Received 0 Likes on 0 Posts
Also because the approach and maneuvering speeds with partial flaps/slats can be different than the FMS target speeds - and the FMS might not necessarily know it.

Bottom line: non standard config - non standard speeds have to be used.
Sidestick_n_Rudder is offline  
Old 6th Oct 2017, 03:45
  #5 (permalink)  
 
Join Date: Jun 2007
Location: Wanderlust
Posts: 3,396
Likes: 0
Received 0 Likes on 0 Posts
Boyington is asking why Vapp also flown selected when it can be easily flown managed since we have corrected it in MCDU.fpuentegomez seems to have given logical answer
vilas is offline  
Old 7th Oct 2017, 21:04
  #6 (permalink)  
 
Join Date: Aug 2013
Location: Middle Europe
Posts: 80
Likes: 0
Received 0 Likes on 0 Posts
i don't see any wording explicitly prohibiting the use of GS mini in mentioned cases once you're in LDG config given VAPP is amended accordingly in MCDU
sierra_mike is offline  
Old 8th Oct 2017, 01:24
  #7 (permalink)  
 
Join Date: Feb 2002
Location: US
Posts: 108
Likes: 0
Received 0 Likes on 0 Posts
Because the autothrust system will not allow the speed to decrease below the manoeuvring speed, if you keep the speed managed.

If you have the flaps stuck at 1+f for example, you'll need flap lever position 2 for landing. (to get the slats extended in position 2) The calculated Vapp will be lower than the manoeuvring speed, so it needs to be selected.
KingAir1978 is offline  
Old 8th Oct 2017, 01:49
  #8 (permalink)  
Thread Starter
 
Join Date: Aug 2001
Location: Above the Horizon
Posts: 124
Likes: 0
Received 0 Likes on 0 Posts
What exactly do you imply by manoeuvring speed? Do you mean VLS? Thanks.
Boyington is offline  
Old 8th Oct 2017, 04:36
  #9 (permalink)  
 
Join Date: Nov 2004
Location: Stormy Peninsular
Posts: 153
Likes: 0
Received 0 Likes on 0 Posts
F and S speeds are manoeuvring speeds.

Check out the abnormal procedure from the FCTM as it is also explained there.
Chrome is offline  
Old 8th Oct 2017, 04:51
  #10 (permalink)  
 
Join Date: Jun 2007
Location: Wanderlust
Posts: 3,396
Likes: 0
Received 0 Likes on 0 Posts
sierra_mike
i don't see any wording explicitly prohibiting the use of GS mini in mentioned cases once you're in LDG config given VAPP is amended accordingly in MCDU
Since the QRH recommends use of select speed it takes out the GS mini out of equation. No need to expressly ban GS mini.
KingAir1978
Because the autothrust system will not allow the speed to decrease below the manoeuvring speed, if you keep the speed managed.
If you have the flaps stuck at 1+f for example, you'll need flap lever position 2 for landing. (to get the slats extended in position 2) The calculated Vapp will be lower than the manoeuvring speed, so it needs to be selected.
What you are saying is exactly opposite of what happens. S and F speeds come from flap lever position and not actual surface. So with flaps jammed at 1+F if you move the lever to position two the speed will come down to F which will be unsafe because one of the surface hasn't extended and that is why you use select speed. But the question asked is after you have configured to Vapp why can't the rest of the approach be flown in managed speed?
vilas is offline  
Old 8th Oct 2017, 08:00
  #11 (permalink)  
 
Join Date: Jul 2000
Location: My views - Not my employer!
Posts: 1,030
Likes: 0
Received 0 Likes on 0 Posts
Been a while since I was on the Bus, but...

I always understood a part of the reason for using selected in these instances was due to the fact you were in direct law for landing hence had no autotrim. As GS mini oscillates the speed around the workload is going to increase for the PF as he has to retrim for each change in speed, which isn't something which is regularly practiced on the Bus... Nor is convenient if you are in manual thrust too..
Cough is online now  
Old 8th Oct 2017, 09:38
  #12 (permalink)  
 
Join Date: Aug 2013
Location: Middle Europe
Posts: 80
Likes: 0
Received 0 Likes on 0 Posts
Since the QRH recommends use of select speed it takes out the GS mini out of equation. No need to expressly ban GS mini.
my current QRH only mentions to select VFE-5kt in order to configure safely. once in LDG config i don't see the procedure speaking against managed speed. purely speaking about being in LDG config, no question about the other phases.
since we use managed SPD for landing in normal daily ops i would expect airbus to explicitly tell us not to use it if they don't want us to. i.e. as they do for overweight landing procedure "SPEED AT RUNWAY THRESHOLD: VLS"
sierra_mike is offline  
Old 8th Oct 2017, 11:07
  #13 (permalink)  
 
Join Date: Jun 2007
Location: Wanderlust
Posts: 3,396
Likes: 0
Received 0 Likes on 0 Posts
Cough
I think in direct law to stay in trim for a fixed Vapp speed is a very valid point. However the new QRH creates an impression that managed speed can be used at Vapp. It only says decelerate to calculated Vapp.
sierra_mike
As you correctly noted there are some changes to Landing with slats or flaps jam QRH procedure. Following notes have been deleted:
1. Use of selected speed is recommended.
2. Autopilot may be used down to 500ft AGL.
3. ATHR is recommended except B+G LO PR warning.
However in VLS greater than VFE next case is retained which can be interpreted as ATHR can be used. Below from QRH:
If VLS is greater than VFE NEXT (overweight landing case), the FLAPS lever can be set in the required next position, while the speed is reduced to follow VLS reduction as surfaces extend. The VFE warning threshold should not be triggered. In this case, disconnect the A/THR . A/THR can be re-engaged when the landing configuration is established.

Last edited by vilas; 8th Oct 2017 at 14:51.
vilas is offline  
Old 8th Oct 2017, 14:06
  #14 (permalink)  
 
Join Date: Aug 2013
Location: Middle Europe
Posts: 80
Likes: 0
Received 0 Likes on 0 Posts
If VLS is greater than VFE NEXT (overweight landing case), the FLAPS lever can be set in the required next position
true that vilas! i have the impression that i might not have expressed myself clearly before with

since we use managed SPD for landing in normal daily ops i would expect airbus to explicitly tell us not to use it if they don't want us to.
what i meant: if airbus doesn't want us to touchdown with a managed speed target utilizing GS mini (as we normally do) they would specifically point it out as they do for example in the overweight landing procedure "SPEED AT RUNWAY THRESHOLD: VLS"
sierra_mike is offline  
Old 9th Oct 2017, 07:59
  #15 (permalink)  
 
Join Date: Mar 2012
Location: London
Age: 42
Posts: 21
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by Chrome
F and S speeds are manoeuvring speeds.

Check out the abnormal procedure from the FCTM as it is also explained there.
Chrome,
Unless our fcom's ar different, F &S are min speeds for retraction not manoeuvring. Pro sup 10

VLS is however a manoeuvre speed. 1.13 vs after take off, 30 degree bank turn stall speed increase is approx 1.08,
1.23 vs after retraction of 1 stage, 1.28 vs clean
Stall speed increase for 45 degree bank is 1.19, so you've got at least 30 bank avail + 15 over bank at VLS
LHRPony is offline  
Old 9th Oct 2017, 11:28
  #16 (permalink)  
 
Join Date: Jun 2007
Location: Wanderlust
Posts: 3,396
Likes: 0
Received 0 Likes on 0 Posts
I stand corrected. According to Airbus they are manoeuvre speeds but not limitations. It is safe to fly between VLS and Vmax (VMO, VLE, VFE). The required aerodynamic margin is properly ensured. Also in Slat/flap jam Autopliot use upto 500ft. is relocated and not removed.

Last edited by vilas; 11th Oct 2017 at 12:02.
vilas is offline  
Old 13th Oct 2017, 19:22
  #17 (permalink)  
 
Join Date: Nov 2004
Location: Stormy Peninsular
Posts: 153
Likes: 0
Received 0 Likes on 0 Posts
Hi LHRPony,

Taken from the FCTM that I have;
Abnormal Flaps/Slats Configuration
Failure During The Approach
... With A/THR operative, the managed speed target will become the next manoeuvring characteristic speed e.g. S speed when selecting flap lever to 1...
Chrome is offline  
Old 14th Oct 2017, 01:42
  #18 (permalink)  
 
Join Date: Oct 2015
Location: 43N
Posts: 264
Likes: 0
Received 0 Likes on 0 Posts
vilas

My motto is, "I wish I knew what I wish I knew."

I am a huge fan of this forum. It is one of the very few places on the sewer of the internet where fresh water is available.

Vilas, as a 319/320 pilot, Captain, and Line Check Airman, I always have put great value into your input into this forum. Your correction only adds to that value.
CaptainMongo is offline  
Old 14th Oct 2017, 10:55
  #19 (permalink)  
 
Join Date: Jun 2007
Location: Wanderlust
Posts: 3,396
Likes: 0
Received 0 Likes on 0 Posts
Thanks mate!
vilas is offline  
Old 14th Oct 2017, 14:31
  #20 (permalink)  
 
Join Date: Mar 2012
Location: London
Age: 42
Posts: 21
Likes: 0
Received 0 Likes on 0 Posts
Cheers Chrome,
So we have fcom defining they are retraction speeds, fctm saying they are man speeds.
Genuine question, what manoeuvre margin exists at the f and S? it's defined for VLS,but I haven't come across any definition for manoeuvre margin for f and s.
And not wishing to get into a tit for tat, it does also say if their is a discrepancy between fcom and fctm then fcom takes precedence.
But as always happy to be corrected.
Thanks for your input, always good to rattle these things around and see where we end up.
LHRPony is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.