Go Back  PPRuNe Forums > Flight Deck Forums > Tech Log
Reload this Page >

Most demanding loads on aircraft landing gear

Tech Log The very best in practical technical discussion on the web

Most demanding loads on aircraft landing gear

Old 21st Jul 2016, 20:42
  #1 (permalink)  
Thread Starter
 
Join Date: Apr 2008
Location: nowhere
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
Most demanding loads on aircraft landing gear

From an article I am reading,

"Landing gear is designed to last the lifetime of an aircraft and operate flawlessly every time. All components are designed to endure the most demanding structural loads, which for a wide-body aircraft is a high-speed turn off an active runway, not a landing or takeoff."
JammedStab is offline  
Old 21st Jul 2016, 22:03
  #2 (permalink)  
 
Join Date: Jan 2008
Location: Reading, UK
Posts: 15,787
Received 196 Likes on 90 Posts
Sideways loads are always going to be more of a challenge for a landing gear to absorb than vertical ones.
DaveReidUK is offline  
Old 21st Jul 2016, 22:18
  #3 (permalink)  
 
Join Date: Feb 2002
Location: UK
Age: 58
Posts: 3,462
Received 135 Likes on 73 Posts
"Landing gear is designed to last the lifetime of an aircraft and operate flawlessly every time.
Those gear changes I did whilst in the hangars must have been a dream then.
TURIN is offline  
Old 22nd Jul 2016, 07:20
  #4 (permalink)  
 
Join Date: Mar 2006
Location: USA
Posts: 2,509
Likes: 0
Received 0 Likes on 0 Posts
Why would it be limited to widebodies?
Check Airman is offline  
Old 22nd Jul 2016, 08:55
  #5 (permalink)  
Thread Starter
 
Join Date: Apr 2008
Location: nowhere
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by TURIN
Those gear changes I did whilst in the hangars must have been a dream then.
Maybe that statement includes overhauls.
JammedStab is offline  
Old 22nd Jul 2016, 09:34
  #6 (permalink)  
 
Join Date: Aug 2000
Location: uk
Posts: 1,771
Received 17 Likes on 9 Posts
I once sold a control system to BA Engineering for use in their huge hard chromium plating shop. All they did in there was refurbish undercarriages. I don't know if it is still there.
On one of my early visits I was being shown around and spotted a complete u/c leg, wheels and all. All the metal parts of the lower u/c leg were blue from excess heat. I was told that this was caused by a single heavy landing and I still find it unbelievable that one single shock load could cause sufficient heating to raise the temperature of such a mass of metal to a temperature of about 500 degrees C. I was assured that it was so but they also pointed out that it wasn't off a BA aircraft.

While the undercarriages may last the life of the aircraft they do seem to require sufficient refurbishment to justify such a large dedicated engineering establishment.
pulse1 is offline  
Old 22nd Jul 2016, 11:22
  #7 (permalink)  
 
Join Date: Jan 2014
Location: N5109.2W10.5
Posts: 720
Likes: 0
Received 0 Likes on 0 Posts
I still find it unbelievable that one single shock load could cause sufficient heating to raise the temperature of such a mass of metal to a temperature of about 500 degrees C.
I agree.
I suspect the heavy landing was reference to heavy braking. (maybe a rejected take off from high speed).
Goldenrivett is offline  
Old 22nd Jul 2016, 11:31
  #8 (permalink)  
 
Join Date: Aug 2000
Location: uk
Posts: 1,771
Received 17 Likes on 9 Posts
I suspect the heavy landing was reference to heavy braking. (maybe a rejected take off from high speed).
GR, that is exactly what I thought at the time but the engineer who was my guide assured me that it was from a single heavy landing and that they get quite a lot of similar u/c units for repair (not BA of course).
pulse1 is offline  
Old 22nd Jul 2016, 11:43
  #9 (permalink)  
 
Join Date: Jan 2014
Location: N5109.2W10.5
Posts: 720
Likes: 0
Received 0 Likes on 0 Posts
Hi pulse1,

Even a heavy landing of say 1,000 feet per min at touch down is only 10 kts vertically. That amount of energy is tiny compared to full heavy braking from say 150 kts (or more with some flap problem.)

The overheating signs (blue due oxidation interference pattern) must have come from the heat transfer from very hot brakes.

Last edited by Goldenrivett; 22nd Jul 2016 at 12:10.
Goldenrivett is offline  
Old 22nd Jul 2016, 13:55
  #10 (permalink)  
 
Join Date: Oct 2013
Location: McHales Island
Age: 68
Posts: 180
Likes: 0
Received 1 Like on 1 Post
" spotted a complete u/c leg, wheels and all. All the metal parts of the lower u/c leg were blue from excess heat. I was told that this was caused by a single heavy landing and I still find it unbelievable that one single shock load could cause sufficient heating to raise the temperature of such a mass of metal to a temperature of about 500 degrees C."


Don't think so boys and girls. Yes pulse1 totally agree. Where was this 500C heat generated from? Brakes or from inside the shock strut, or both?


Brake heat at that temp would result in the fusible plugs melting on the wheel rims and resulting in flat tyres and possible wheel rim magnesium fire. Then heat transfer through wheel assemblies to landing gear trucks and associated structure AND melting the protective paint to expose "blue metal".... don't think so.


Heat generated from within the shock strut? Definately not. The strut assembly is an overgrown shockstrut just like on our cars. It is filled with a combination of oil and nitrogen and on compression through an orifice will produce next to no temp rise at all. If temps did rise to 500C (which it won't) the strut O-rings would melt and you would have a deflated strut and vast pools of oil on the ground around the gear. In my 40yr career I have never seen or heard of such a thing. Keep smiling....


McHale.
Capt Quentin McHale is offline  
Old 23rd Jul 2016, 10:35
  #11 (permalink)  
 
Join Date: Jan 2003
Location: Seoul/Gold Coast.....
Posts: 383
Received 2 Likes on 2 Posts
Certification requirements..

From what I can recall, all transport category A/C are required to withstand a vertical load of 600 feet/minute at maximum landing weight and 360 feet/minute at maximum take-off weight, so there is a lot of margin to cover firm/hard landings, I know of one B777 operator with a 40 kt. crosswind limit and the normal procedure is to land crab on.....the torsional loads on the main gear attachment points must be incredible but the airframe obviously can take it, even at Max LDG Wt. of about 251,000 kg......
zlin77 is offline  
Old 24th Jul 2016, 13:22
  #12 (permalink)  
 
Join Date: Feb 2009
Location: Virginia
Posts: 2,058
Received 28 Likes on 22 Posts
As a hobby blacksmith, I know that pounding on a piece of cold metal will make it hot. Some smith even show off by lighting cigarettes that way, though I've never seen that in person. But you have to deform the metal a lot to get it hot -- for example forging the square end of a bar into a point.

I'm pretty sure that steel absorbs very little energy simply by being stressed; it only gets hot through plastic deformation. Otherwise, think what would happen to the connecting rods and valve springs in piston engines, for example.
Chu Chu is online now  
Old 25th Jul 2016, 09:16
  #13 (permalink)  
 
Join Date: Aug 2014
Location: Miami, FL
Posts: 17
Likes: 0
Received 0 Likes on 0 Posts
Pulse1, I can't support the 500 deg C temperature, but what some seem to be overlooking is that shock absorbers function precisely by generating heat. Kinetic energy is absorbed by internal fluid friction forces within the shock, resulting in heat, which heat is what dissipates the descent rate.

Basic physics -- unless the shocks are converting their work to electricity or powering some device or storing energy, then if they did not generate heat, they would necessarily function only as springs, and the airplane would go bouncing back up into the air. This is our friend, the First Law of Thermodynamics (aka conservation of energy) at play.

The fact that the descent of the massive tonnage of a large commercial aircraft is able to be arrested by dissipating all that energy (in the form of heat) with such a small device as a shock absorber, and in such a short time as it takes to compress the strut, does lend credibility to the idea that they could get noticeably hotter with a hard landing.

The question is how much hotter.

We all know the heat generated from the brakes is sufficient to cause a fire, so that would be one's first thought as to the cause when looking at heat damage on landing gear. And as someone pointed out, the brakes have a lot more kinetic energy to dissipate because the forward speed is so much faster than the vertical descent rate (about 2 orders of magnitude more energy).

The temperature limits of hydraulic fluid and seals tell us the shocks are not intended to get very hot (nothing remotely approaching 500 deg C). But there will be some temperature increase of the strut from the shock absorption during a very hard landing (though I would guess less than a 50 deg C increase, rather than 500 deg C). If someone has actual data, it would be fascinating to find out.

Last edited by Mach Stall; 25th Jul 2016 at 13:23.
Mach Stall is offline  
Old 25th Jul 2016, 14:04
  #14 (permalink)  
 
Join Date: Dec 2001
Location: what U.S. calls Žold EuropeŽ
Posts: 941
Likes: 0
Received 0 Likes on 0 Posts
Hevily depends on the type of aircraft. Short range aircraft have their take of of weight close to the landing weight and get beaten several flights a day. Long range aircraft may do just one flight per day, but they taxi out significantly more heavy than they land. Fast turns on taxi out may indeed produce the highest sideloads. Depending on the design of the gear again, this may create the highest stress in the most critical locations, while the stress distributes much more evenly on a straight landing.
Volume is offline  
Old 25th Jul 2016, 15:20
  #15 (permalink)  
 
Join Date: Aug 2000
Location: uk
Posts: 1,771
Received 17 Likes on 9 Posts
Mach Stall,

Very nice to have a contribution from someone who understands the thermodynamics. My estimate of 500 degrees was based on my experience that tells me that this is the minimum sort of temperature which will blue steel, particularly over such a short time scale.

For those who are equating this with normal heavy landings, it is obvious that we are talking here of landings which required the undercarriage to be replaced. What other damage may have occurred, I have no idea.
pulse1 is offline  
Old 25th Jul 2016, 23:24
  #16 (permalink)  
 
Join Date: Feb 2009
Location: Virginia
Posts: 2,058
Received 28 Likes on 22 Posts
No matter how hard the landing, the struts can only compress so far -- beyond that the energy has to go somewhere else. I guess other things, for example the wings, would then flex, and to some extent they would flex back and cycle the struts again. But it seems hard to imagine a vastly greater amount of energy going into the struts on a hard landing than on just a firm one.

Oh, and on plain steel it takes 575 degrees F (about 300 C) to get a blue temper. But it might well be significantly higher on chrome plate.
Chu Chu is online now  
Old 26th Jul 2016, 02:16
  #17 (permalink)  
 
Join Date: Sep 2007
Location: USA
Posts: 601
Likes: 0
Received 0 Likes on 0 Posts
pulse1-

I don't think the chrome plated surfaces you saw were heated to 500degC. The MLG components (hydraulic struts, axles, etc) base metal thin dense chrome plating is applied to is usually heat treated to very high strength levels. Exposure to temperatures of 500degC would significantly alter the base metal properties, and I don't think the component would be salvageable.

There are only a few surfaces of a commercial aircraft MLG that are plated with thin dense chrome. These are typically surfaces subject to sliding contact with seals or bushings, to reduce friction, minimize wear, and prevent corrosion. Often shaft surfaces in contact with bearing races are plated with thin dense chrome to inhibit fretting. And sometimes the plating is used to refurbish shaft surfaces that have been scratched or abraded.

The blue hue you saw on the MLG component plated surfaces may have been due to one of the processes involved in the refurbishment procedure. One of the first things done after dis-assembly is to strip/clean the part surfaces, and then perform NDI to check for structural damage. If any chrome plated surfaces require repair, the first step is to electro-chemically strip the old plating.

There is high demand for refurbished commercial aircraft landing gear assemblies. So as long as the components are safe/serviceable/salvageable, they will be refurbished and put back into service.

Here is a good article describing the landing gear overhaul process:
http://www.avitrader.com/wp-content/...O_2011-091.pdf
riff_raff is offline  
Old 26th Jul 2016, 07:53
  #18 (permalink)  
 
Join Date: Nov 2007
Location: Near the Mountains of Sussex
Posts: 270
Received 1 Like on 1 Post
Pulse 1 .............

The BA Landing Gear shop was offloaded ( outsourced ) to a company called Hawker Pacific quite a few years back.... they in turn have been taken over by Lufthansa Technik.

Not much left to sell off......... next on the list is the whole Engineering operation at LGW


have carried out quite a few Overweight / Heavy Landing Inspections, never found any of the reported "Blueing" on external visible parts... Suspect that it was as previously suggested , a RTO and or Brake sieze.

Last edited by Blink182; 26th Jul 2016 at 08:22.
Blink182 is offline  
Old 27th Jul 2016, 11:48
  #19 (permalink)  
 
Join Date: Mar 2004
Location: Oxfordshire
Age: 54
Posts: 470
Likes: 0
Received 0 Likes on 0 Posts
Not forgetting that if the aircraft had been in the sky for several hours at the usual cruising altitudes, the undercarriage would be pretty chilly at the point of touchdown.

I've had a complete covering of ice on the gear (and wing lower surfaces) having descended through cloud on a winter approach.
glum is offline  
Old 31st Jul 2016, 19:02
  #20 (permalink)  
 
Join Date: Jan 2016
Location: St Albans
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Back to the OP, few years ago an engineer who'd spent his working life on Vulcans said the critical case with undercarage was the turning torque on the 'static' leg as the aircraft 'screws' around tightly as it manovers.
JamesBird is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.