Go Back  PPRuNe Forums > Flight Deck Forums > Tech Log
Reload this Page >

737 Speed brakes and roll rate questions

Tech Log The very best in practical technical discussion on the web

737 Speed brakes and roll rate questions

Old 26th Dec 2012, 16:37
  #1 (permalink)  
Thread Starter
 
Join Date: Dec 2007
Location: Lithuania
Posts: 129
Likes: 0
Received 0 Likes on 0 Posts
737 Speed brakes and roll rate questions

Hi,

I saw in multiple places at FCOM that roll rates are increased while using speed brakes. Can anybody explain why it is so aerodynamically? I looked at b737.org. There is explanation but I cannot understand it. I don't see any difference between photo 2 and 4

Why it was done so? Was it impossible to design speed brakes without roll rate changes?
Turbavykas is offline  
Old 26th Dec 2012, 17:03
  #2 (permalink)  

Do a Hover - it avoids G
 
Join Date: Oct 1999
Location: Chichester West Sussex UK
Age: 90
Posts: 2,206
Likes: 0
Received 0 Likes on 0 Posts
Not quite sure what is bothering you however a couple of things could be involved.

Looking at your bottom picture it would appear to me that the turbulent flow that would be formed by the airbrake being extended could easily have some effect on the nearby aileron.

Also the basic roll damping of the wing could be changed by airbrake extension. The less efficient a wing is at producing lift is likely to reduce its natural roll damping. (Roll damping being due to a down going wing producing more lift thanks to the AoA increase and the upgoing one less lift - which naturally damps the roll).

Given that airbrakes are only used infrequently I would not expect the designers to compromise the basic aileron/roll rate design isues in order to counter an airbrake effect.

JF
John Farley is offline  
Old 26th Dec 2012, 17:06
  #3 (permalink)  
 
Join Date: May 2008
Location: Sheffield
Posts: 155
Likes: 0
Received 3 Likes on 3 Posts
If you have half speedbrake extended, and then apply aileron full right, does the speedbrake on the left wing retract? It certainly looks like it from the photos.

If you had no speedbrake extended, then there would be none to retract.
911slf is offline  
Old 26th Dec 2012, 21:06
  #4 (permalink)  
 
Join Date: Jan 2006
Location: US
Posts: 2,205
Likes: 0
Received 0 Likes on 0 Posts
Aerodynamically? Because the plane rolls more for a given displacement of the yoke. Why? Because partial spoilers and the retraction or extension thereof, increases the roll sensitivity.

If you don't have a video of the yoke inputs and rate of movement along with a simultaneous view of the outside spoilers it might be impossible to explain using the pictures provided.
misd-agin is offline  
Old 26th Dec 2012, 21:49
  #5 (permalink)  
 
Join Date: Apr 2008
Location: nowhere
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by Turbavykas
Hi,

I saw in multiple places at FCOM that roll rates are increased while using speed brakes. Can anybody explain why it is so aerodynamically?
I believe that your increased roll rate is when you have partial speed brake extension, not full.

For a given amount of normal aileron deflection, there is a greater displacement difference between the roll spoilers at half speedbrake deployment than when at full speedbrake or no speedbrake..

Last edited by JammedStab; 26th Dec 2012 at 21:56.
JammedStab is offline  
Old 26th Dec 2012, 22:03
  #6 (permalink)  
fdr
 
Join Date: Jun 2001
Location: 3rd Rock, #29B
Posts: 2,944
Received 847 Likes on 251 Posts
With full speed brake, the roll rate will also be higher, it is not limited to the partial speed brake condition.

In the partial case, the opposite wing spoiler drop couples with the roll side spoiler rise, giving an increased rate, as well as the increased loading of the outer wing for a given condition, which increases the roll response of the ailerons alone. Yes, the AoA is generally higher with the speed brake up, and that acts to mitigate the aileron effectiveness to a point, but mainly at the very high AoA case approaching stall, not at the normal AoA's in operation.

With full speedbrake, the aileron effectiveness alone increases roll rate, if the AoA of the outer section is below stall AoA.

The above is not necessarily true for the B777, 787 or the Airbus, where the controls may change the scheduling of the spoilers and the aileron deflection for a given operating condition. Having said that, the B777 roll rate is increased with spoilers up... On the A320, recall that the roll scheduling was done by the position of the flap handle, and if the TE flaps were stuck at full flap, then repositioning the flap handle would lead to divergence with or without the autopilot engaged.... due to the excessive roll sensitivity from the spoiler deflection with a full flap position. (HDA323 - OEB117)
fdr is offline  
Old 27th Dec 2012, 04:45
  #7 (permalink)  
 
Join Date: Apr 2008
Location: nowhere
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
If I remember correctly on the 727, no speed brakes equals normal roll rate. Half speedbrake equals very high roll rate. Full speed brake equals a roll rate similar to the roll rate with no speedbrake extension(but maybe not exactly the same...I don't know).
JammedStab is offline  
Old 27th Dec 2012, 04:56
  #8 (permalink)  
 
Join Date: Jul 2005
Location: USA/Europe/Central Asia
Posts: 162
Likes: 0
Received 0 Likes on 0 Posts
It is the same.. I flew them both
noneya is offline  
Old 27th Dec 2012, 08:02
  #9 (permalink)  
 
Join Date: Jul 2000
Location: My views - Not my employer!
Posts: 1,030
Likes: 0
Received 0 Likes on 0 Posts
I think the last two pictures may contain a red herring - Ground spoilers deployed (not avail in flight).
Cough is offline  
Old 27th Dec 2012, 13:03
  #10 (permalink)  
 
Join Date: Apr 2010
Location: Home soon
Posts: 0
Likes: 0
Received 0 Likes on 0 Posts
Flight spoilers assist the ailerons in rolling the aircraft.
Flight spoilers deploy as the control wheel is displaced past 11 degrees to reach a maximum deflection when past 70 degrees.
They also deploy but symetrically when used via the speed brake lever,at the flight detent,the flight spoilers are at their full deflection of 20 deg and 22.5 deg for the inboard and outboard respectively.

So if in turn with the wheel displacement increasing past the 11 degrees and the spoilers in flight detent,the roll will not be increased as the spoilers would already be in their full deployed via the speed brake.

In any position other than flight detent,an increase in bank( wheel displacement more than 11 deg) will end up with more up spoilers on one side than the other.
If the lever is increased fast and especially with flaps ,overbanking may occurr and or AP disconnect.

Last edited by de facto; 27th Dec 2012 at 13:06.
de facto is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.