Go Back  PPRuNe Forums > Flight Deck Forums > Tech Log
Reload this Page >

A320 accuracy check

Tech Log The very best in practical technical discussion on the web

A320 accuracy check

Old 8th May 2010, 18:09
  #1 (permalink)  
Thread Starter
 
Join Date: Apr 2009
Location: worldwide
Posts: 40
Likes: 0
Received 0 Likes on 0 Posts
A320 accuracy check

Hi,
it is said in the FCOM that the check is valid provided the distance difference is less than 3 miles (1 mile for approach). no mention of difference in bearing ? what if the bearing difference is 5, 20 or 40° ?
foff is offline  
Old 8th May 2010, 18:20
  #2 (permalink)  
 
Join Date: Mar 2006
Location: Choroni, sometimes
Posts: 1,974
Likes: 0
Received 0 Likes on 0 Posts
Don't understand.

More than one ore three miles off is off. It's that simple.
hetfield is offline  
Old 8th May 2010, 23:41
  #3 (permalink)  
 
Join Date: Jul 2007
Location: ***
Posts: 350
Likes: 0
Received 0 Likes on 0 Posts
As a DME/DME is the preferred way to fix the position by the FMS (no GPS), only DME values might be mentioned. The second best conventional fix is Bearing/DME, that is what you are referring to.
It's been a while since I have been on the 320, and I don't have access to a maual, but we just tuned a VOR and compared the Bearingpointer and the DME to the FMS map. Distance accurate and pointer pointing at the tuned station - accuracy check ok.

Nic
Admiral346 is offline  
Old 9th May 2010, 19:43
  #4 (permalink)  
Thread Starter
 
Join Date: Apr 2009
Location: worldwide
Posts: 40
Likes: 0
Received 0 Likes on 0 Posts
let's take an example then.
FMGC says VOR/DME ABC is located bearing 150°/20 nm but raw data are 165°/21nm. according to FCOM a check is valid if distance difference is less than 3 nm but doesn't say anything about difference in bearing. the above test is then valid or not ? (15° of bearing diff & 1 nm of distance diff)
foff is offline  
Old 9th May 2010, 20:51
  #5 (permalink)  
 
Join Date: Aug 2007
Location: UK
Age: 32
Posts: 53
Likes: 0
Received 0 Likes on 0 Posts
Not sure if its correct, but you could calculate the distance between the two points (raw data and FMGC); in this case about 5.44nm which is more than 3... then again, that might be looking at it in an overly mathematical way!
Diaz is offline  
Old 9th May 2010, 21:11
  #6 (permalink)  
 
Join Date: May 2007
Location: Italy
Age: 36
Posts: 204
Likes: 0
Received 0 Likes on 0 Posts
FMGC says VOR/DME ABC is located bearing 150°/20 nm but raw data are 165°/21nm. according to FCOM a check is valid if distance difference is less than 3 nm but doesn't say anything about difference in bearing. the above test is then valid or not ? (15° of bearing diff & 1 nm of distance diff)
The accuracy check is done both on distance and bearing:
1. DISTANCE: compare NAVAID distance with FM distance on ND or check with FM PROG page: error shall be less than or equal to 3 NM (1 NM on approach).
2. BEARING: Check that the needle (raw data) overlies the corresponding blue navaid symbol (FM computed).

Hope that helps,
fredgrav
fredgrav is offline  
Old 10th May 2010, 02:06
  #7 (permalink)  
 
Join Date: Apr 2010
Location: in the flight deck
Posts: 89
Likes: 0
Received 0 Likes on 0 Posts
what if the bearing difference is 5, 20 or 40° ?
2. BEARING: Check that the needle (raw data) overlies the corresponding blue navaid symbol (FM computed).
hmm.....meaning no difference allowed?
Neupielot is offline  
Old 10th May 2010, 06:22
  #8 (permalink)  
Thread Starter
 
Join Date: Apr 2009
Location: worldwide
Posts: 40
Likes: 0
Received 0 Likes on 0 Posts
thtat's the point !
foff is offline  
Old 10th May 2010, 06:36
  #9 (permalink)  
 
Join Date: May 2007
Location: Italy
Age: 36
Posts: 204
Likes: 0
Received 0 Likes on 0 Posts
hmm.....meaning no difference allowed?
You got it !
fredgrav is offline  
Old 10th May 2010, 09:46
  #10 (permalink)  
 
Join Date: Oct 2009
Location: UK
Posts: 1,270
Likes: 0
Received 0 Likes on 0 Posts
Hi foff,

You have to be practical about this - say you are looking for a position accuracy of better than 3 nms: If the DME distance and FMGC computed distance were the same, then the bearing could be off by the equivalent of 3 nms - by my simple trig that's 3 degs at 60 nm, or about 9 degs if 20 miles away.

edit e.g. If you had 2 VORs - both 20 miles away, A is due North from you and B is due West.

FMGC position check gives:
A = 22.9 miles and due North of you,
B = 20.0 miles and 278 degs from you.

I'd say both confirm I'm within 3 nms of my FMGC position.

Last edited by rudderrudderrat; 10th May 2010 at 10:48. Reason: maths example
rudderrudderrat is offline  
Old 10th May 2010, 11:44
  #11 (permalink)  
DFC
 
Join Date: Mar 2002
Location: Euroland
Posts: 2,814
Likes: 0
Received 0 Likes on 0 Posts
Speaking in general terms, when required to conform FMC position accuracy eg before MNPS I use 2 or 3 DME stations.

Tune and ident DME station. Ask FMS how far to DME station and compare the result.

Repeat for another station (or 2) preferably one left of track and the other right of track to get a good spread.

Provided that the FMC and DME distances are not more than the allowed distance appart each time then everything is OK.

I only use VOR/DME if there is no other DME. The reason is that the VOR has a +/- bearing accuracy which at distance is far wortse than the DME accuracy.

Having said that to check the accuracy using VOR/DME I would go with "rudderrudderrat". provided that the indicated position (VOR/DME fix) is less than the maximum distance from the FMC indicated position, the FMC indicated position is accurate enough.

It should be possible to check distance from FMC posiiton to IRS position and GPS position etc so that when one is no longer in range of DME/DME position fixing one can expect that the GPS / IRS positions will do the job.
DFC is offline  
Old 10th May 2010, 12:42
  #12 (permalink)  
 
Join Date: May 2007
Location: Italy
Age: 36
Posts: 204
Likes: 0
Received 0 Likes on 0 Posts
by my simple trig that's 3 degs at 60 nm
Hi rudder,
a small doubt's arising: should I be checking the NAV accuracy throughout the approach (eg. GPS primary lost), will I have enough time to apply the 60-to-1 rule in determining whether the distance between the NAV/FM bearing is within the max limit or not ? Being the probability for a discrepancy in bearing only not very usual and should discr. be unacceptable, at that point, I'd take FM position as unaccurate thus continuing raw data ... right ?

Thanks,
fredgrav
fredgrav is offline  
Old 10th May 2010, 13:23
  #13 (permalink)  
 
Join Date: Oct 2009
Location: UK
Posts: 1,270
Likes: 0
Received 0 Likes on 0 Posts
Hi fredgrav,

Our company makes it "simples".

The primary aids we use for the approach are the ones published on the Jepp.
If we have GPS Primary & accuracy is High - then we may use the MAP overlay as an aid to SA.
rudderrudderrat is offline  
Old 11th May 2010, 11:00
  #14 (permalink)  
 
Join Date: Dec 2008
Location: melb
Posts: 2,162
Likes: 0
Received 0 Likes on 0 Posts
Ok you bus guru's here an 'off subject' question because I didn't want to start a new thread for one question.
I've been keenly reading about the auto flight system on the A320 & am puzzled that should a selected hdg be chosen for say ATC req's then the CLB mode (which I assume is managed if FMA says CLB) reverts to OP CLB meaning any previous ALT constraints in the MCDU Flt-Pln will be ignored. I understand that OP CLB does that (ignores constraints) but why would it be automatically selected when hdg only is in selected mode?

Hopefully some simple answers for an Airbus novice here


Wmk2
Wally Mk2 is offline  
Old 11th May 2010, 11:20
  #15 (permalink)  
 
Join Date: Oct 2009
Location: UK
Posts: 1,270
Likes: 0
Received 0 Likes on 0 Posts
Hi Wally,

If you are not NAVigating to a waypoint because you have selected a HeaDinG - then it can't apply any constraints because it may never get there.

Last edited by rudderrudderrat; 11th May 2010 at 11:22. Reason: spelling
rudderrudderrat is offline  
Old 11th May 2010, 11:30
  #16 (permalink)  
 
Join Date: Dec 2008
Location: melb
Posts: 2,162
Likes: 0
Received 0 Likes on 0 Posts
ok tnxs 'Rudd' I guess that means seeing as we are now in heading mode Alt constraints would normally only be associated with a pre installed flt pln in the MCDU right? I Imagine that any ALT constraints that need to be considered (from the previous flt pln route) would have to be manually selected by the pilot on the FCU? That's the way I am forming a picture here with all this.
If the Lat nav is then reset to managed as in back towards the flt pln does the OP CLB revert back to managed CLB automatically?
All fascinating stuff, yeah I know I gotta get a life right? Well am about to undertake a 'bus' course & so far this pre study stuff I've been doing has left me with a head full of stuff that would choke a brown dog!


Wmk2
Wally Mk2 is offline  
Old 11th May 2010, 12:39
  #17 (permalink)  
Thread Starter
 
Join Date: Apr 2009
Location: worldwide
Posts: 40
Likes: 0
Received 0 Likes on 0 Posts
by design you must have a managed lateral mode to have a managed vertical mode. that's why when you go heading, initial CLB or DES, both managed modes, can't be maintained. then reversion with a triple click to selected (=not managed) mode, ie OPDES or OPCLB. coming back to NAV doesn't imply coming back to vertical managed mode previously engaged. you must repush to engage again the managed vertical mode
foff is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.