FADEC and battery
Thread Starter
Join Date: Jul 2000
Location: London
Posts: 1,256
Likes: 0
Received 0 Likes
on
0 Posts
FADEC and battery
Had a query relevant to loss of all power in B744. After the battery drops out, apart from loss of standby instruments etc does the FADEC and hence engine control drop out as well?
Join Date: Aug 2007
Location: The Netherlands
Age: 67
Posts: 288
Likes: 0
Received 0 Likes
on
0 Posts
FADEC Power
FADEC's (or EEC's) are normally powered by a dedicated little generator, driven by their own engine.
Do not mistake that little power source for the normal engine driven generator!
The EEC generator (or alternator) will deliver enough power already at very low engine RPM (so also during windmilling airstarts). It will usually have separate coils for the two EEC channels. Often the electrics needed to carry the signal from thust lever to EEC are also powered from that generator.
In other words, even with the most complete electrical power failure on board, the engine control should still be unhampered.
Only as a backup to the EEC alternators will there be a connection from aircraft electrical system to EEC; on the ground, before engine is turned by the starter, could be an example of aircraft electrics powering the EECs.
Do not mistake that little power source for the normal engine driven generator!
The EEC generator (or alternator) will deliver enough power already at very low engine RPM (so also during windmilling airstarts). It will usually have separate coils for the two EEC channels. Often the electrics needed to carry the signal from thust lever to EEC are also powered from that generator.
In other words, even with the most complete electrical power failure on board, the engine control should still be unhampered.
Only as a backup to the EEC alternators will there be a connection from aircraft electrical system to EEC; on the ground, before engine is turned by the starter, could be an example of aircraft electrics powering the EECs.
Join Date: Feb 2004
Location: Australia
Posts: 1,307
Likes: 0
Received 0 Likes
on
0 Posts
After the battery drops out, apart from loss of standby instruments etc does the FADEC and hence engine control drop out as well?
As long as the engine core rpms (N2) remain above 9% (CF6) or N3 remains above 8% (RB211), the ECU/EEC's are powered (courtesy of engine-driven permanent magnet alternators).
But if the rpms go this low, you have probably fallen out the sky already... and you can probably assume that the engine has flamed out.. and without battery power, you won't be able to relight.
Rgds.
NSEU
Join Date: Feb 2004
Location: Australia
Posts: 1,307
Likes: 0
Received 0 Likes
on
0 Posts
"The control alternator meets all EEC power requirements when N2 increases above 11%. It continues to meet the requirements until N2 decreases below 9%. If one phase of either or both windings fails, the control alternator continues to meet all EEC power requirements if N2 is above 45%"
Join Date: Mar 2000
Location: Arizona USA
Posts: 8,571
Likes: 0
Received 0 Likes
on
0 Posts
These small separate AC generators have been used in the past on large piston types as well...those aircraft equipped with CurtisElectric propellors, for example.
Total electric failure from the aircrafts electrical system/ships battery...props still controllable.
A CAR4b requirement.
Total electric failure from the aircrafts electrical system/ships battery...props still controllable.
A CAR4b requirement.
Join Date: Feb 2004
Location: Australia
Posts: 1,307
Likes: 0
Received 0 Likes
on
0 Posts
The EEC's permanent magnet "dedicated alternator" is mechanically driven (via a gearbox) by the spinning "N3 rotor" of the aircraft's engine: The Rolls Royce Trent on the Boeing 777 has 3 rotors (N1, N2 and N3).
For beginners: A rotor is basically a shaft (solid or hollow) with "stages" of blades at intervals along it. The only rotor you can really see is the big N1 compressor "fan" at the front of the engine. If you looked in the back of the engine, you would see the N1 "turbine" blades. The N2 and N3 rotors are nestled inside the engine (between the N1 compressor and turbine blades).
If the engine is turning, either by normal means.. or by windmilling (at flight speeds), the N3 will be turning.
For beginners: A rotor is basically a shaft (solid or hollow) with "stages" of blades at intervals along it. The only rotor you can really see is the big N1 compressor "fan" at the front of the engine. If you looked in the back of the engine, you would see the N1 "turbine" blades. The N2 and N3 rotors are nestled inside the engine (between the N1 compressor and turbine blades).
If the engine is turning, either by normal means.. or by windmilling (at flight speeds), the N3 will be turning.