Go Back  PPRuNe Forums > Flight Deck Forums > Rumours & News
Reload this Page >

BAW and NY approach at it

Rumours & News Reporting Points that may affect our jobs or lives as professional pilots. Also, items that may be of interest to professional pilots.

BAW and NY approach at it

Old 4th Oct 2019, 08:18
  #1 (permalink)  
Thread Starter
 
Join Date: Mar 2006
Location: USA
Posts: 2,509
Likes: 0
Received 0 Likes on 0 Posts
BAW and NY approach at it


Never flown a widebody. Is 180kt to 5nm incompatible with a stabilised approach?
Check Airman is offline  
Old 4th Oct 2019, 08:21
  #2 (permalink)  
 
Join Date: May 2006
Location: FL510
Posts: 910
Received 0 Likes on 0 Posts
Impossible on A330 and B777
safelife is offline  
Old 4th Oct 2019, 09:17
  #3 (permalink)  
 
Join Date: Aug 2015
Location: Sunnydale
Posts: 251
Received 38 Likes on 23 Posts
Flap 30 is usual for 22L at JFK. Flap limiting speed for flap 30 is 180. At best they’ll be doing gear down flap 25 but Boeing don’t recommend using F25 as an intermediate setting. So gear down Flap 20. From 5 slow down to 170 before selecting flap 30 and still be stable at 1000’ is going to be tight. Not helped by the DME at us airfields showing 1.2 ish miles at touchdown.
back to Boeing is online now  
Old 4th Oct 2019, 09:21
  #4 (permalink)  
 
Join Date: Sep 2011
Location: USA
Posts: 255
Received 22 Likes on 5 Posts
Rumor has it he was last spotted somewhere east of Recife on a 130 heading, still not answering the question.
PukinDog is offline  
Old 4th Oct 2019, 09:24
  #5 (permalink)  
 
Join Date: Feb 2019
Location: Onboard
Posts: 21
Likes: 0
Received 0 Likes on 0 Posts
KJFK Runway 22L is 2560m long. That’s a pretty short runway for a 747-400.

The crew will be planning flap 30, and autobrake 4, with partial/full reverse.

Flap 30 has a placard speed of 180 knots, and likely to offer a final approach speed at typical landing weight of less than 140kts? Shall we say 5 miles is approximately 1,500 ft? Maybe less, as the associated DME overreads by more than a mile!

BA has very strict Stablised Approach Criteria. (I accept others are less strict.) So that’s 500’ (or less!) to move comfortably away from flap limiting speed, before selecting flap 30, whilst achieving a 35 knot reduction in 500’ or less, in an aircraft with significant momentum.

IMVHO, that’s a pretty tight corner to ask this crew to accept, and that’s before we consider the meteorology on the day.

Perhaps we might reasonably ask, why that requirement was imposed on that one aircraft on that day. It certainly isn’t normal. Even in New York. If it were, there’d be an awful lot of aircraft going around!

Purely subjectively, it looks to me like a pretty stupid request/instruction.

Last edited by Toolonginthisjob; 4th Oct 2019 at 09:41.
Toolonginthisjob is offline  
Old 4th Oct 2019, 09:46
  #6 (permalink)  
 
Join Date: Dec 2003
Location: Tring, UK
Posts: 1,822
Received 2 Likes on 2 Posts
Never flown a widebody. Is 180kt to 5nm incompatible with a stabilised approach?
It would depend on a lot of things: Vref, wind, terrain, icing, density altitude, etc.

I can do 160/4 in the 777-200 and 170/5 in the 777-300 in benign conditions without too much drama at average weights but 180/5 would probably need a fair amount of speedbrake and early gear/flap deployment. Don’t know about the 747 but probably more difficult.

Anyway, the whole idea of Stabilised Approaches is that you have freed up capacity to monitor for external/internal issues, such as deviations, windshear, other traffic and so on. Being rushed in on a high-workload, last-minute will-we-won’t-we approach is not a great idea. Smacks of “are we up here because you’re down there or are you down there because we’re up here...?”
FullWings is offline  
Old 4th Oct 2019, 11:24
  #7 (permalink)  
 
Join Date: Aug 2007
Location: The sky
Posts: 327
Likes: 0
Received 4 Likes on 1 Post
180 to 6 is just doable in a 747, as is 170 to 5 and 160 to 4. Note this is distance to the threshold and not the actual DME reading which is often not co located and requires a headwind on approach and a three degree slope.

A decent controller can achieve the same landing rate without the stress by slowing the aircraft earlier and achieving accurate final separation earlier. This controller is trying to mitigate her lack of accuracy and forward planning by asking the flight crew to perform an unwise higher than desirable energy final approach. She then punishes a crew that demonstrate airmanship and refuse an undesirable clearance. They also demonstrate airmanship by refusing the clearance instead of agreeing to it and then decelerating when they want to as many crews would have done.

Im sure an ASR was filed and I doubt anything will be done.

LD
Locked door is offline  
Old 4th Oct 2019, 12:52
  #8 (permalink)  
 
Join Date: Dec 2013
Location: Elsewhere
Posts: 608
Received 67 Likes on 27 Posts
22L threshold is at 1.4 DME, so she’s asking for 180+ to 1200’ (3.6 nm from the threshold). How she thinks that’s in any way a sensible requirement is beyond me.
itsnotthatbloodyhard is offline  
Old 4th Oct 2019, 13:03
  #9 (permalink)  
 
Join Date: Jun 1999
Location: Oztrailia
Posts: 2,991
Received 14 Likes on 10 Posts
Ridiculous, this kind of rubbish happens all too frequently. JFK approach need to wind it in.
ACMS is offline  
Old 4th Oct 2019, 13:06
  #10 (permalink)  
Guest
 
Join Date: Apr 2009
Location: On the Beach
Posts: 3,336
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by back to Boeing
Flap 30 is usual for 22L at JFK. Flap limiting speed for flap 30 is 180. At best they’ll be doing gear down flap 25 but Boeing don’t recommend using F25 as an intermediate setting. So gear down Flap 20. From 5 slow down to 170 before selecting flap 30 and still be stable at 1000’ is going to be tight. Not helped by the DME at us airfields showing 1.2 ish miles at touchdown.
I guess it's all what you're used to. D12.0 at ROSLY, D6.8 AT ZALPO (the FAF), D.1.4 at the threshold. If the DME were biased to read 0.0 at the threshold, then ROSLY would be D10.6, and ZALPO would be D5.4. Can't see where the DME being biased would matter outside the FAF.

But, someone who wants zero at the threshold could request the RNAV Y Runway 22L.
aterpster is offline  
Old 4th Oct 2019, 13:11
  #11 (permalink)  
 
Join Date: Sep 2007
Location: New York
Posts: 224
Likes: 0
Received 0 Likes on 0 Posts
JFK

Originally Posted by itsnotthatbloodyhard
22L threshold is at 1.4 DME, so she’s asking for 180+ to 1200’ (3.6 nm from the threshold). How she thinks that’s in any way a sensible requirement is beyond me.
Up until six months ago fought that JFK fight every day.
ATC there are great, they really are, but like all of us, they learn on the job. If an operator regularly flys at 180 until 3 miles, an expectation has been set and they'll ask for that. Previous crews likely backed themselves into a corner or were unstablised and continued to 'make ATC happy'.
In the US, use the word 'Unable'. there's no need to invoke 'FAA standards' like this crew did. Leave it at that one word and make it ATC's problem.
Then either ask for their phone number; or use your company' channels to explain what your procedures and requirements are. ATC do want to work with everybody.

neilki is offline  
Old 4th Oct 2019, 13:25
  #12 (permalink)  
 
Join Date: Jun 2019
Location: VA
Posts: 210
Likes: 0
Received 0 Likes on 0 Posts
My take - both the controller and the pilot on the radio were being needlessly snippy toward each other.

The low altitude airspace around JFK can be very congested at times (limited options for vectoring) and arrival flows tightly spaced to maintain expected arrival rates. It is a very challenging piece of airspace to work.

The JFK final controller was trying to manage a flow of traffic based on the expectation that everyone could hold 180 KIAS to 5 DME. Maybe not the best plan in the world, but I'm guessing that they use that plan often enough, and crews (mostly) comply, so that was the plan for the moment.

British Air said they were unable to maintain the requested airspeed. Fair enough. At that point, the controller needs to either slow everyone behind BA down, possibly causing a domino effect back to the previous controller, or pull BA out of the sequence and reinsert them with additional spacing. That decision had to be made in fairly short order, however, the radio calls to work this out could have been handled a bit more diplomatically by both sides.

The proper place to have resolved this dilemma was on the previous frequency. The need to maintain a certain speed to a certain DME could have been inserted into the ATIS broadcast or passed on by the first approach controller at which time the proper spacing could have been worked out. By the time it wound up in the final controller's lap, the options to fix it were limited.
Tomaski is offline  
Old 4th Oct 2019, 14:00
  #13 (permalink)  
 
Join Date: Oct 2011
Location: UK
Posts: 355
Likes: 0
Received 0 Likes on 0 Posts
correct me if I’m wrong but I always thought in the states if the controller gives you a speed to maintain on approach your allowed +/- 10 kts? He could had then done 170kts with no issue!

A320baby is offline  
Old 4th Oct 2019, 14:09
  #14 (permalink)  
 
Join Date: Nov 2000
Location: UK
Posts: 121
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by Tomaski

British Air said they were unable to maintain the requested airspeed. Fair enough. At that point, the controller needs to either slow everyone behind BA down, possibly causing a domino effect back to the previous controller, or pull BA out of the sequence and reinsert them with additional spacing. That decision had to be made in fairly short order, however, the radio calls to work this out could have been handled a bit more diplomatically by both sides.
No, at that point what the controller needs to do is ask them, if they can’t maintain the assigned speed, at what point they will need to slow down from 180 to final approach speed, which is exactly what she did, but all she got in return was bla bla big airplane stabilized approach, bla bla. Even when she said that they weren’t answering the question the crew failed to come up with their requirements, so her choice was slow everybody down to160 ten miles out or break BA off the approach. Nothing wrong with saying ‘UNABLE’ but keep it to that and come up with your own plan instead of blocking the frequency during rush hour at one of the world’s busiest airports with a major runway shut down for the whole summer.
Long Haul is offline  
Old 4th Oct 2019, 15:21
  #15 (permalink)  
 
Join Date: Aug 2010
Location: Herefordshire
Posts: 1,093
Received 4 Likes on 3 Posts
Check Airman

Suggest you move this to ATC Issues then you may get a response from the World's best controllers - London!

B48N ( long retired LHR controller )
Brian 48nav is offline  
Old 4th Oct 2019, 15:38
  #16 (permalink)  
 
Join Date: Jul 2007
Location: Germany
Posts: 1,022
Likes: 0
Received 6 Likes on 1 Post
I have always found controllers respond well to reasonable communication. The BA pilot was absolutely right to point out that he was unable to maintain the assigned speed. There is of course a margin but if you accept an impossible speed and then fly ten knots slower the controller will continue to assign impractical speeds. Where it went wrong was BA blocking the frequency with a long winded explanation and approach getting frustrated and responding by taking him out of the sequence.
lederhosen is online now  
Old 4th Oct 2019, 15:58
  #17 (permalink)  
 
Join Date: Mar 2012
Location: Having a margarita on the beach
Posts: 2,402
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by lederhosen
Where it went wrong was BA blocking the frequency with a long winded explanation and approach getting frustrated and responding by taking him out of the sequence.
Yep.
Director or Final frequencies are possibly the worst places (not that any other frequency is the right one) to start a conversation about Your aircraft energy capabilities, especially around very busy intercontinental airport. Anybody flying in radar controlled busy airport terminal areas knows that You will be very likely assigned speeds on final approach, so better be proactive and include during the briefing what speeds You are able to make at the estimated arrival GW with current weather forecast, and adjust the figure (i.e. 180 kt to 6 nm) once You are getting to finals and are aware of your tail/head wind component. In that scenario, probably "Unable, we can make 170 kt to 5 nm" (that is basically 180 kt to 6 nm) would have worked wonders. For sure JFK controllers are in some cases not easy to deal with, but You need to come up with a plan anyway.
sonicbum is offline  
Old 4th Oct 2019, 16:36
  #18 (permalink)  
Thread Starter
 
Join Date: Mar 2006
Location: USA
Posts: 2,509
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by A320baby
correct me if I’m wrong but I always thought in the states if the controller gives you a speed to maintain on approach your allowed +/- 10 kts? He could had then done 170kts with no issue!
Perhaps at a smaller airport, with less traffic. Please do not do that at JFK, or any other large, busy airport.
Check Airman is offline  
Old 4th Oct 2019, 16:38
  #19 (permalink)  
Thread Starter
 
Join Date: Mar 2006
Location: USA
Posts: 2,509
Likes: 0
Received 0 Likes on 0 Posts
Thanks for all the replies guys. Seems it’s hard in a 747.

I can’t move the thread, Brian.
Check Airman is offline  
Old 4th Oct 2019, 17:17
  #20 (permalink)  
 
Join Date: Aug 2007
Location: inmysuitcase
Posts: 209
Received 0 Likes on 0 Posts
By ACMS:
Ridiculous, this kind of rubbish happens all too frequently. JFK approach need to wind it in.
I fully agree.
My company is paying their company.
So, i think, we as pilots, have more rights to complain about ATC. (I know this will upset some people....)

Now, IF, JFK atc is paying my company for their service, they have a point (but they do not..)

I flew many times to jfk, you just cannot even plan what they want, they do last minute changes even in low vis, changing runways etc.

Tell me/us way in advance what you want and we will adapt (help you girls and guys) but don't leave for the last 3-4 minutes.

I understand you girls and guys have to cope with a lot of traffic and nationalities, so why don't you all start with speaking a bit slower?
I am used to your accent, many or not (esp. grnd freq.......is even more freq congestion!)

We can all work together but it has to come from 2 sides, and IMHO we as pilots are more in our rights than ATC, especially after a 8-10 (or more!) LH flight.

Off for the weekend, back next Thursday in......JFK

T.P.

testpanel is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.