Wessex lovers?
Join Date: Oct 2009
Location: West Sussex
Age: 84
Posts: 148
Likes: 0
Received 0 Likes
on
0 Posts
Sycamore
My only worry was that someone not using the right gear, and not being familiar with the job, may get hurt. As an ex Wessex chief engineer, I must have done many gearboxes, but the potential for losing fingers is always there.
The 3deg mast tilt means you cannot get a straight lift on the mast, you have to tilt the aircraft at an extreme angle. The S76 is the same, but with a 5deg tilt.
My only worry was that someone not using the right gear, and not being familiar with the job, may get hurt. As an ex Wessex chief engineer, I must have done many gearboxes, but the potential for losing fingers is always there.
The 3deg mast tilt means you cannot get a straight lift on the mast, you have to tilt the aircraft at an extreme angle. The S76 is the same, but with a 5deg tilt.
Join Date: Feb 2006
Location: Hanging off the end of a thread
Posts: 32,468
Received 2,594 Likes
on
1,098 Posts
When you take the gearbox off wasn’t there a couple of cables you had to add to prevent the canopy sagging fwd.
Join Date: Oct 2009
Location: West Sussex
Age: 84
Posts: 148
Likes: 0
Received 0 Likes
on
0 Posts
Not to my knowledge NutLoose, but I never worked on any of the Navy versions, perhaps they had extra gear. Anyone who has read Richard Pikes book helicopter boys, will have read about the Bristow crash in Indonesia. This was an ex Brunei army Mk. 50, and it was jinxed. We spent Two years rebuilding it at Redhill, after which it went to Port Harcourt in Nigeria, after a year or so of good service it turned over due to ground resonance. It was repaired again on site, only to be finally lost after I left due to a tail servo malfunction. As for as I know its still there in he swamp.
Barney Swinton-Bland was flying a Whirlwind in PH, when he had a blade pocket lift, we rescued him as he floated merrily down the river on his pontoons. We dumped the blade, and the next time we flew over we saw that the locals had retrieve it, mounted it no tressles and were using it to cut up fish on. Who say Shell dont care for the environment.
Barney Swinton-Bland was flying a Whirlwind in PH, when he had a blade pocket lift, we rescued him as he floated merrily down the river on his pontoons. We dumped the blade, and the next time we flew over we saw that the locals had retrieve it, mounted it no tressles and were using it to cut up fish on. Who say Shell dont care for the environment.
Black `bodge-tape`(long before`speed-tape) was the answer to lifted pockets on WW.....until you flew thru` the next tropical rain shower.....or until the `Glovers` sorted the problem...eventually...
Do you remember the silver metallic tape that was stuck along the leading edges of Wessex V blades in the Far East to reduce erosion from heavy rain? All that happened was that the rain split the tape and your leading edge had all the aerodynamics of a house brick! And with all the attendant vibration................Happy days
We had clear blade tape in NI in the 80's which often lifted in heavy rain causing the classic 'Wop, Wop' sound.
The tape usually removed itself if you kept flying but on one occasion it didn't and we landed and shut down to discover that one of the blade pockets had removed itself instead!
The tape usually removed itself if you kept flying but on one occasion it didn't and we landed and shut down to discover that one of the blade pockets had removed itself instead!
In Borneo we found that the standard Smith & Wesson .38 and 12 rounds we were issued with was useless. Shooting against a headwind you could see the bullet and if it got more than twenty yards the bullet was so far off target that you victim was fireproof.
You could tear the old black blade tape into very thin strips. One would then wrap them into the groove on the 9 mm cartridge. The enabled you to place them in the chamber of a .38 Smith & Wesson and the tape would act like the rim on the pistol's cartridge.
The difference was fantastic and with the bigger charge six shots into a fuel drum at 50 yards was easy. The only problem was that you had to poke the empty shells out with a screwdriver as the extractor would not grip the tape..
!2 rounds of II WW ammunition or unlimited 9 mm from the Ghurkas? No contest.
You could tear the old black blade tape into very thin strips. One would then wrap them into the groove on the 9 mm cartridge. The enabled you to place them in the chamber of a .38 Smith & Wesson and the tape would act like the rim on the pistol's cartridge.
The difference was fantastic and with the bigger charge six shots into a fuel drum at 50 yards was easy. The only problem was that you had to poke the empty shells out with a screwdriver as the extractor would not grip the tape..
!2 rounds of II WW ammunition or unlimited 9 mm from the Ghurkas? No contest.
Last edited by Fareastdriver; 11th Oct 2020 at 17:49.
Join Date: Sep 2009
Location: Just over the road from Bicester airfield
Age: 80
Posts: 440
Likes: 0
Received 2 Likes
on
1 Post
Couple of Wessex with head sling in place, although shouldn't really lift the head with blades attached if I remember correctly ?.
Join Date: Sep 2017
Location: Wallingford
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
The sling" shown in the photo is not strictly a head sling but a sling capable of lifting the head and gearbox as a complete unit. It is of all metal construction (probably mild steel) and can be used to lift not only the head and gearbox unit but the compete aircraft! The head (only) sling is a four legged wire rope sling affair of altogether more flimsy construction.
With regard to the query about cockpit wire rope cables, they should be fitted to support the cockpit rear bulkhead when the longerons either side of the main gearbox are to be removed prior to lifting the gearbox. They fit between the lower forward corner of the sliding window rail and the top rear corner of the sloping bulkhead.
Incidentally the aircraft does not have to be tilted to remove/refit a main gearbox. A couple of strong guys pulling rearwards on the gearbox A frames as the gearbox is lifted/lowered will allow the front A frame legs to "clear" the base of the cockpit bulkhead.
With regard to the query about cockpit wire rope cables, they should be fitted to support the cockpit rear bulkhead when the longerons either side of the main gearbox are to be removed prior to lifting the gearbox. They fit between the lower forward corner of the sliding window rail and the top rear corner of the sloping bulkhead.
Incidentally the aircraft does not have to be tilted to remove/refit a main gearbox. A couple of strong guys pulling rearwards on the gearbox A frames as the gearbox is lifted/lowered will allow the front A frame legs to "clear" the base of the cockpit bulkhead.
Join Date: Oct 2009
Location: West Sussex
Age: 84
Posts: 148
Likes: 0
Received 0 Likes
on
0 Posts
Sorry Sycamore I was never very good at keeping diaries, but this would have been Summer 1965, after the New Zealand Regiment took over the area, from the Gurkhas, I was in charge of maintenance at Simanggang. Your right about it being 225, and shortly before Sam Smiths accident, operating from Kuching.
Join Date: Feb 2006
Location: Hanging off the end of a thread
Posts: 32,468
Received 2,594 Likes
on
1,098 Posts
With regard to the query about cockpit wire rope cables, they should be fitted to support the cockpit rear bulkhead when the longerons either side of the main gearbox are to be removed prior to lifting the gearbox. They fit between the lower forward corner of the sliding window rail and the top rear corner of the sloping bulkhead.
Far East Driver, does this bring back any memories.