Go Back  PPRuNe Forums > Aircrew Forums > Rotorheads
Reload this Page >

Compressor stall in a 206L

Rotorheads A haven for helicopter professionals to discuss the things that affect them

Compressor stall in a 206L

Old 17th Jan 2019, 14:19
  #1 (permalink)  
Thread Starter
 
Join Date: Dec 2016
Location: TN
Posts: 56
Received 1 Like on 1 Post
Compressor stall in a 206L

I have a couple of questions about the emergency procedures for compressor stall in the 206L. The POH says that if you have the indications of a stall or a stall itself, then you are to turn on the engine anti icing and (if installed) the heater. I’m having a hard time understanding this because antiicing takes hot P3 air and uses it in the compressor support housing thus increasing the temp of the incoming air through the turbine. Your cabin heat takes air away from the turbine and redirects it as cabin heat? Both of those seem counter intuitive to helping cool an engine. Any insight would be great thanks guys!
Weads is offline  
Old 17th Jan 2019, 16:10
  #2 (permalink)  
 
Join Date: Oct 2006
Location: SA
Posts: 33
Likes: 0
Received 0 Likes on 0 Posts
The idea is to unload the compressor a bit, not to cool it. Kind of like opening a small bleed valve.
Compressor stalls are independent of temperature. The temperature spike is the result of the stall.
Airmotive is offline  
Old 17th Jan 2019, 17:41
  #3 (permalink)  
 
Join Date: Sep 2002
Location: Great South East, tired and retired
Posts: 4,348
Likes: 0
Received 193 Likes on 89 Posts
The compressor stalls because of back pressure in the compressor, so any way of bleeding off that pressure a bit by taking that pressurised air away will help.
Ascend Charlie is offline  
Old 17th Jan 2019, 19:47
  #4 (permalink)  
 
Join Date: May 2002
Location: Downeast
Age: 75
Posts: 18,267
Received 466 Likes on 190 Posts
How about something really novel....and reduce Collective or perhaps roll the Throttle back but stay in the Green Arc for Rotor RPM if in flight?
SASless is offline  
Old 17th Jan 2019, 21:20
  #5 (permalink)  
 
Join Date: Jan 2000
Location: Bar to Bar
Posts: 795
Received 7 Likes on 2 Posts
Originally Posted by SASless
How about something really novel....and reduce Collective or perhaps roll the Throttle back but stay in the Green Arc for Rotor RPM if in flight?
With a whole 25 hours on type, I'm with you. I'm pretty certain it would take me longer to find the different controls to turn on heating etc opposed reduce collective.
Sloppy Link is offline  
Old 18th Jan 2019, 02:47
  #6 (permalink)  
LRP
 
Join Date: Mar 2011
Location: Arizona
Posts: 219
Likes: 0
Received 21 Likes on 12 Posts
Originally Posted by Sloppy Link

With a whole 25 hours on type, I'm with you. I'm pretty certain it would take me longer to find the different controls to turn on heating etc opposed reduce collective.
FYI

3-3-E. ENGINE COMPRESSOR STALL/
SURGE
• INDICATIONS:
1. Engine pops.
2. High or erratic TOT.
3. Decreasing or erratic N1 or N2.
4. TORQUE oscillations.
• PROCEDURE:
1. Collective — Reduce power,
maintain slow cruise flight.
2. TOT AND N1 — Check for normal
indications.
3. ENGINE ANTI-ICING switch — ON.
4. PARTICLE SEP PRG switch (if
installed) — ON.
5. HEATER switch (if installed) — ON.
NOTE
Severity of compressor stalls/surges
will dictate if engine should be shut
down and treated as an engine
failure. Violent stalls/surges can
cause damage to engine and drive
system components, and must be
handled as an emergency condition.
Stalls/surges of a less severe nature
(one or two low intensity pops) may
permit continued operation of engine
at a reduced power level, avoiding
condition that resulted in
compressor stall/surge.
If pilot elects to continue flight:
6. Collective — Increase slowly to
achieve desired power level.
7. TOT and N1 — Monitor for normal
response.
8. Land as soon as practical.
If pilot elects to shut down engine:
9. Enter autorotation.
10. Throttle — Closed.
11. FUEL VALVE switch — OFF.
12. Accomplish autorotative descent and
landing. (Refer to AUTOROTATIVE
DESCENT PROCEDURE, paragraph
3-3-A-3).
LRP is offline  
Old 18th Jan 2019, 03:06
  #7 (permalink)  
 
Join Date: May 2002
Location: Downeast
Age: 75
Posts: 18,267
Received 466 Likes on 190 Posts
LRP,

The Original Poster noted what the POH had to say and asked for some additional input.

If the Engine gives three or four low intensity pops....what do you recommend doing as you posted an excerpt from some unknown source as you did not specify from where it comes from.
SASless is offline  
Old 18th Jan 2019, 03:16
  #8 (permalink)  
 
Join Date: Apr 2008
Location: cape town
Posts: 61
Received 1 Like on 1 Post
Originally Posted by SASless
How about something really novel....and reduce Collective or perhaps roll the Throttle back but stay in the Green Arc for Rotor RPM if in flight?
First action is to reduce power demand by lowering collective but rolling off throttle has to be one of the craziest things I've ever heard! There is only 1 justification that I can think of for playing with the throttle in flight and that is dealing with tail rotor emergencies just before touch down. After reducing power demand then turn on engine anti icing in case engine inlet icing is starving the compressor of air resulting in a compressor stall.
bront is offline  
Old 18th Jan 2019, 04:39
  #9 (permalink)  
 
Join Date: May 2002
Location: Downeast
Age: 75
Posts: 18,267
Received 466 Likes on 190 Posts
Bront,

What happens when you reduce Engine RPM to Minimum Power On Nr momentarily and roll the throttle back up to full throttle as set before the Compressor Stall occurred?

If you lower the Collective first and attempt to cure the problem that way and it does not work.....the next thing you are told to do is turn on the bleed air heater and anti-ice.

What does that action do for you?

Can you not get much the same reaction by slowing the engine RPM....and reducing the flow of air to the compressor?
SASless is offline  
Old 18th Jan 2019, 08:04
  #10 (permalink)  
 
Join Date: Jan 2000
Location: Bar to Bar
Posts: 795
Received 7 Likes on 2 Posts
Originally Posted by LRP
FYI

3-3-E. ENGINE COMPRESSOR STALL/
SURGE
• INDICATIONS:
1. Engine pops.
2. High or erratic TOT.
3. Decreasing or erratic N1 or N2.
4. TORQUE oscillations.
• PROCEDURE:
1. Collective — Reduce power,
maintain slow cruise flight.
2. TOT AND N1 — Check for normal
indications.
3. ENGINE ANTI-ICING switch — ON.
4. PARTICLE SEP PRG switch (if
installed) — ON.
5. HEATER switch (if installed) — ON.
NOTE
Severity of compressor stalls/surges
will dictate if engine should be shut
down and treated as an engine
failure. Violent stalls/surges can
cause damage to engine and drive
system components, and must be
handled as an emergency condition.
Stalls/surges of a less severe nature
(one or two low intensity pops) may
permit continued operation of engine
at a reduced power level, avoiding
condition that resulted in
compressor stall/surge.
If pilot elects to continue flight:
6. Collective — Increase slowly to
achieve desired power level.
7. TOT and N1 — Monitor for normal
response.
8. Land as soon as practical.
If pilot elects to shut down engine:
9. Enter autorotation.
10. Throttle — Closed.
11. FUEL VALVE switch — OFF.
12. Accomplish autorotative descent and
landing. (Refer to AUTOROTATIVE
DESCENT PROCEDURE, paragraph
3-3-A-3).
To just be clear, that was seven years ago, I'm still in current flying practice on others to a total of.......? I'm not getting into the willy waving of hours and years flown, point remains, quicker to reduce power than to start fumbling for switches.
Sloppy Link is offline  
Old 18th Jan 2019, 09:34
  #11 (permalink)  
 
Join Date: Feb 2006
Location: Germany
Posts: 919
Received 5 Likes on 3 Posts
I had an occurence once with a passenger flight.
Reduced collective and it stopped, until I raised it again.
Nursed the bird back to base with the occasional surge again - looking for autorotative reachable spots all the way... calming down the passengers ;-)
When they striped the engine they found, that parts from the compressor housing, there where the compressorwheels spin, went through the engine.
After seeing the amount, which went through, an outside landing would have been the better decison....
If you don´t have knowledge of i.e. salty environment causing an engine surge, better treat it as an engine failure on its way....
Flying Bull is offline  
Old 18th Jan 2019, 09:39
  #12 (permalink)  
 
Join Date: Jun 2016
Location: Brantisvogan
Posts: 1,033
Received 57 Likes on 37 Posts
A surge on a healthy engine would be unusual these days, eliminating external or environmental factors it is safe to presume that the primus may be about to shuffle off its mortal coil.
Bell_ringer is offline  
Old 18th Jan 2019, 10:35
  #13 (permalink)  
 
Join Date: Nov 2006
Location: Pensacola, Florida
Posts: 770
Received 29 Likes on 14 Posts
Who on earth has ever experienced a compressor stall in an L-model? Nobody I've ever heard of.
FH1100 Pilot is offline  
Old 18th Jan 2019, 12:37
  #14 (permalink)  
 
Join Date: Apr 2008
Location: cape town
Posts: 61
Received 1 Like on 1 Post
Originally Posted by SASless
Bront,

What happens when you reduce Engine RPM to Minimum Power On Nr momentarily and roll the throttle back up to full throttle as set before the Compressor Stall occurred?

If you lower the Collective first and attempt to cure the problem that way and it does not work.....the next thing you are told to do is turn on the bleed air heater and anti-ice.

What does that action do for you?

Can you not get much the same reaction by slowing the engine RPM....and reducing the flow of air to the compressor?
A compressor stall is caused by the compressor not being able to supply enough air at a high enough pressure to the combustion chamber. The pressure in the combustion chamber then pushes back into the compressor causing it to stall. If nothing changes this will cycle continuously until something fails. This lack of air can be from a number of reasons, partially blocked intake, damaged compressor or air leaking between the compressor and combustion chamber.

Rolling off the throttle and then rolling it on again will do the following IMO. Firstly as the engine slows it will probably stop the stall briefly but once stabilized at the lower RPM the engine will still need to produce about the same amount of power if you have not lowered the collective and I would expect it to stall again. Then if you open the throttle again the engine will try to speed up to increase the rotor RPM and this will demand the most power yet and it will stall again.

I don't know for sure if slowing the RPM will do what I believe because I have never experienced it but I know for a fact that accelerating the rotor will cause it to stall as I have experienced this myself. In my case my L3 had a corroded compressor housing which caused the magnesium to have large raised areas like blisters that were rubbing against the impellor. Whilst taking off in the dark and trying to move the movable landing light forward with my left thumb, I accidently put my finger on the rotor RPM beep trim button instead and was inadvertently trying to accelerate the rotor RPM to a higher value. Each time I pushed the button forward I was rewarded with a load bang and an extremely violent yaw and the bystanders witnessed a good 6 feet of flame out the tailpipe. Very impressive apparently!

If you lower the collective and that doesn't fix the problem, then you have a very serious mechanical fault and the only option is to enter autorotation and shut down the engine. If lowering the collective stops the stall, then turning on the engine anti ice will hopefully remove any ice (if that is the problem) that has built up in the inlet and causing the lack of airflow. Turning on the particle separator, if you have one, will hopefully remove whatever is blocking it. I have no idea what turning on the heater would do except rob the compressor of more air so I do not understand why that is part of the procedure. If anything I would have thought it should say 'Turn it off.'

The stalls I experienced were extremely violent and I'm convinced that if they had been allowed to continue for any length of time would have destroyed the drive train in seconds.

Your idea of rolling off throttle is extremely dangerous IMO. For starters it is not part of any procedure in the flight manual and if memory serves me correctly is in fact prohibited, except for entering autorotation and for tail rotor emergencies. And secondly the rotor RPM and every other gauge will be all over the place and it would be very hard to control, if not impossible. There is only one option initially and that is the same for pretty much every other emergency in a single engine helicopter IMO and that is to lower the collective and only then try to work out what is going on.
bront is offline  
Old 18th Jan 2019, 12:50
  #15 (permalink)  
 
Join Date: Apr 2008
Location: cape town
Posts: 61
Received 1 Like on 1 Post
Originally Posted by Ascend Charlie
The compressor stalls because of back pressure in the compressor, so any way of bleeding off that pressure a bit by taking that pressurised air away will help.
This is completely incorrect. It stalls because of a lack of pressure, not because of too much pressure. Turning on anti ice is to remove any ice that may be blocking the inlet causing low air flow and low pressure.
bront is offline  
Old 18th Jan 2019, 13:34
  #16 (permalink)  
 
Join Date: Oct 1999
Location: Den Haag
Age: 57
Posts: 6,217
Received 315 Likes on 175 Posts
It's too simplistic to talk about too much pressure or too little pressure - it's related to pressure ratio (exit/inlet) and the mass flow. Turning on the heater is opening a bleed - as has been stated - which then modifies the pressure ratio and increases the surge margin. Some aircraft have a switch on the collective that is used to force open the normal bleed valve, even though the Ng is higher that the value at which it normally closes, if it is anticipated that the aircraft will enter conditions conducive to disrupted airflow - typically turbulent airflow on landing or flying through hot gas emissions. Ice is definitely nothing to do with it although it's true that ice can cause surge by disrupting the local airflow.
212man is offline  
Old 18th Jan 2019, 15:47
  #17 (permalink)  
LRP
 
Join Date: Mar 2011
Location: Arizona
Posts: 219
Likes: 0
Received 21 Likes on 12 Posts
Originally Posted by SASless
LRP,

The Original Poster noted what the POH had to say and asked for some additional input.

If the Engine gives three or four low intensity pops....what do you recommend doing as you posted an excerpt from some unknown source as you did not specify from where it comes from.
It's a copy/paste from the L-3/L-4 RFM. Same procedure in the 407 (except the reference to TOT, N1, N2 changes to MGT, Ng, Np). Been the same procedure for years. First step in all is collective reduce.
LRP is offline  
Old 18th Jan 2019, 16:34
  #18 (permalink)  
 
Join Date: May 2002
Location: Downeast
Age: 75
Posts: 18,267
Received 466 Likes on 190 Posts
Yes...right back to the 206A...and probably most helicopters....for sure for single engine helicopters any way.

iIn twins you then have the option to take the bad engine off line and treat it as an engine failure.

SASless is offline  
Old 18th Jan 2019, 17:51
  #19 (permalink)  
 
Join Date: Sep 2002
Location: Great South East, tired and retired
Posts: 4,348
Likes: 0
Received 193 Likes on 89 Posts
This is completely incorrect. It stalls because of a lack of pressure, not because of too much pressure. Turning on anti ice is to remove any ice that may be blocking the inlet causing low air flow and low pressure.
Geez, Bront, why then is a bleed valve or a bleed band fitted to turbine engines? To remove the excess air that can build pressure at the back of the compressor, and cause the flow to break down and stall the compressor blades.

A C20 on start-up has the bleed valve open to allow acceleration of the compressor without getting too much air into the combustor. It stays open, closing gradually, until around 92% N1 when the engine can take all the air OK. It opens again on sudden accelerations. To let out the back pressure and allow the wheels to spin up faster.

Try leaving the wedge in the bleed valve when you go to start next time, hear the stalls start very early on. Too much back pressure.

Anti-ice is still turned on in hot countries too! Because it removes some of the excess air and pressure, not because there is ice in the intakes.
Ascend Charlie is offline  
Old 18th Jan 2019, 18:23
  #20 (permalink)  
 
Join Date: May 2002
Location: Downeast
Age: 75
Posts: 18,267
Received 466 Likes on 190 Posts
One would think the RFM would. have OAT temperature ranges if there was concerns over Icing alone being the cause of the Compressor stall.

It does not....thus it must be intended to be used at all Tems as part of the Emergency Procedure..

Last edited by SASless; 18th Jan 2019 at 21:56. Reason: Clarified what I meant to say....referring to the Emergency procedure and not normal ops.
SASless is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.