Flight Plan Route: naming of points off designated routes
Thread Starter
PPruNaholic!
Joined: Aug 2000
Posts: 1,615
Likes: 0
From: Buckinghamshire
In Safety Sense leaflet 20A "VFR Flight Plans" it says
So, does that mean:[list=1][*]I can put "DCT Portsmouth Harbour" instead of "DCT SAM134012"?[*]I can put "DCT CHERGOURG VRP S" instead of "DCT MP 211009"?[*]etc?[/list=1]I don't mind putting coordinates ref. VOR/NDB etc., but I figure it must be easier for the ATCO's concerned to interpret plain language - but not sure whether "Portsmouth Harbour" passes for a "land feature", and whether "CHERBOURG VRP S" is the correct nomenclature to use?
What do you prefer? Any advice appreciated,
Cheers,
Andy
for flights OFF designated routes, list points normally not more than 30 minutes flying time apart and enter DCT (DIRECT) between successive points. Points may be VORs, VRPs, land features or co-ordinates.
What do you prefer? Any advice appreciated,
Cheers,
Andy
Joined: Feb 2001
Posts: 1,064
Likes: 0
From: Hants, UK
Don't forget also that a VFR plan is really only a guide of your intended route. Because of the need to remain VFR you might not actually make it to the VRP or whatever. In any case, you are likely to be talking to an ATC unit at the points you mention and they will know where you are.
My recommendation is not to get too hung up on specifying every little point on a VFR plan. It does not get transmitted to units on route, so you will have to tell them anyway, and it is really of most use for SAR purposes, when a general search area is OK.
EGTB DCT SAM DCT MP DCT LFRC seems OK to me.
Remember that you are also supposed to put in an EET for the FIR boundary in the Remarks field.
My recommendation is not to get too hung up on specifying every little point on a VFR plan. It does not get transmitted to units on route, so you will have to tell them anyway, and it is really of most use for SAR purposes, when a general search area is OK.
EGTB DCT SAM DCT MP DCT LFRC seems OK to me.
Remember that you are also supposed to put in an EET for the FIR boundary in the Remarks field.
Thread Starter
PPruNaholic!
Joined: Aug 2000
Posts: 1,615
Likes: 0
From: Buckinghamshire
Thanks guys: I was loathe to put "DCT SAM" in because I will avoid their airspace (ref. another thread about Solent Radar SSR being u/s and could we please steer clear etc.).
But as you are saying that I can simply put "SCT SAM DCT MP" etc. without flying that route exactly, just flying something similar to it, and that this won't apprently cause consternation at Solent when I don't call them en-route, then I think I will amend plan to the simpler version.
Thanks guys,
Andy
But as you are saying that I can simply put "SCT SAM DCT MP" etc. without flying that route exactly, just flying something similar to it, and that this won't apprently cause consternation at Solent when I don't call them en-route, then I think I will amend plan to the simpler version.
Thanks guys,
Andy
Joined: Feb 2001
Posts: 1,064
Likes: 0
From: Hants, UK
If you are definitely going to avoid the SAM then why not use somewhere like the IW NDB or even an airways reporting point such as KATHY (right underneath the VFR recommended route). Just becasue you're not in the airway doesn't mean the point doesn't exist.
But to be clear: if you put SAM in and then don't call Solent, they will never miss your presence as they don't get the VFR FPL anyway.
But to be clear: if you put SAM in and then don't call Solent, they will never miss your presence as they don't get the VFR FPL anyway.
Joined: Feb 2003
Posts: 2,042
Likes: 0
From: Oxford
Mike - except a few offshore ones, e.g. NEDUL is there, I think. Presumably they are there precisely so pilots filing cross-channel FPs can use them.
Mind you, if you are using GPS, they are all loaded, usually...
Tim
Mind you, if you are using GPS, they are all loaded, usually...
Tim




