Unusual Accident
Wonder if a better preflight may have saved the day.
Left rudder continuity was established from the cockpit rudder pedals to the rudder control horn; however, right rudder continuity could only be established from the cockpit rudder pedals to the cable end loop, which was not attached to the clevis at the rudder control horn |
Originally Posted by megan
(Post 11636366)
Wonder if a better preflight may have saved the day.
|
Originally Posted by OldLurker
(Post 11636444)
Perhaps. The report states that the aircraft had previously done three sectors that day apparently without incident, two of them flown by the accident pilot (21,000-hour ATPL holder, apparently retired) and one by a friend, neither whom spotted the problem at preflight despite being aware of a “rigging issue”, and neither of whom seems to have felt that the “odd yawing” was serious. Moreover, the NTSB determined the probable cause of the accident to be “the pilot’s decision to unlatch his seatbelt during flight, which allowed him to exit the airplane and impact the tail, resulting in a loss of control and impact with terrain”, not the mis-rigging.
|
Originally Posted by Andrewgr2
(Post 11636534)
But it seems very likely that the pilot only undid his harness to look at the rudder to see why the aircraft had strange yaw characteristics. The disconnected rudder cable should have been easy to spot in a pre-flight inspection- and should certainly not have escaped whatever inspection was done after work had been done on the rudder.
I guess the "take-home" is, if a plane is telling you something is not quite right, do an appropriate set of engineering checks on the ground before committing aviation in it! All in all, a very sad accident........ :uhoh: |
Last time I flew a Cub I would have had to do more than undo my straps to 'fall out' and hit the tailplane?? Was he making his way back along the outside of the fuselage to check the rudder? :confused:
|
If the rudder was disconnected before the flight how does anyone explain that the clevis pin was found at the accident site? Rudder horn clevis pins are typically retained by a cotter pin (split pin UK). If the cotter pin was missing the crash could possibly have caused the clevis pin to fall out. The clevis pin should always be installed head up so it is not likely to fall out in positive g flight.
If a clevis pin was missing on my tailwheel aircraft it would be obvious when I pulled the aircraft out of the hangar, obvious at first attempt to taxi, and if I somehow got that far, would likely cause loss of control at start of takeoff roll. Sorry, but there is no way this rudder was disconnected when the aircraft took off. It is also unlikely that a missing split pin contributed in any way to the flight anomaly that was being investigated. |
I have personal experience that an improperly adjusted tailwheel swivel bearing will cause similar results to the issue this owner was investigating. If the swivel king pin nut is too tight the tailwheel will resist the steering spring as the rudder is deflected. Add a little more rudder pedal force and the tailwheel breaks out causing a sudden rudder movement. It is a very unpleasant control response and one that I knew had to be fixed on the ground before further flight.
In my case the improper adjustment was made in an attempt to eliminate tailwheel shimmy. |
Originally Posted by 42go
(Post 11636728)
Last time I flew a Cub I would have had to do more than undo my straps to 'fall out' and hit the tailplane?? Was he making his way back along the outside of the fuselage to check the rudder? :confused:
|
Originally Posted by EXDAC
(Post 11636766)
I have personal experience that an improperly adjusted tailwheel swivel bearing will cause similar results to the issue this owner was investigating.
https://bhtailwheels.com/our-tailwheels |
Some tailwheels have a plate with a hole into which a ball clicks. If the plate cracks, taxiing is a continuous correction of turning left/right. I've taxied a Jodel DR10 for almost a mile on tarmac with this condition. Surprisingly the replacement plate was cheap and in stock in the UK, so this must be quite common.
|
All times are GMT. The time now is 16:23. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.