Airbus A320 Tech question
Airbus A320 Tech question
Join Date: May 2000
Location: Camp X-Ray
Posts: 2,135
Likes: 0
Received 0 Likes
on
0 Posts
Starter for ten.....
Is it because LGCIU 1 is linked to the air-ground switch which prevents reverser 1 being deployed in flight? Which may also be linked to the requirement to switch off the GPWS because it can't tell if the gear is locked down?
Is it because LGCIU 1 is linked to the air-ground switch which prevents reverser 1 being deployed in flight? Which may also be linked to the requirement to switch off the GPWS because it can't tell if the gear is locked down?
Join Date: Dec 1998
Location: UK
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
Hand Solo and Jet II have it right - LGCIU 1 sends on ground/in flight signals to various services around the aeroplane. In the event of a failure of LGCIU 1, some users will see a "flight" condition, and some will see a "ground" condition. Whether things see flight or a ground condition is dependant on whether it's a proximity detector that's failed or it's an electrical failure of the LGCIU itself. See FCOM 1.32.10 p5.
In either case, the FADEC on the relevant side will see a flight condition, and thus will inhibit reverse on that side, along with a few other things. FCOM 1.32.10 pages 6 and 14 refer.
Cheers
In either case, the FADEC on the relevant side will see a flight condition, and thus will inhibit reverse on that side, along with a few other things. FCOM 1.32.10 pages 6 and 14 refer.
Cheers
Join Date: Jul 2002
Location: Hungary
Age: 39
Posts: 684
Likes: 0
Received 0 Likes
on
0 Posts
I am quite interested to understand the abbreviations in this thread. I am not by any means technical at this level, and would be interested if someone could explain the question to me, so I understand what is being said 
SMooth skies,
Dan
SMooth skies,
Dan
Join Date: Dec 1998
Location: UK
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
No problem!
LGCIU - Landing Gear Control Interface Unit. The aircraft has 2 of these. These are the "brains" of the landing gear system. They give orders and information to bits of the areoplane that need it about the what the landing gear is doing. ie is it up/down/unlocked etc. Also they sequence the movement of the landing gear itself. Amongst other things!
GPWS - Ground Proximity Warning System. Every commercial aircraft has one and it does exactly what it says on the tin - warns the crew of ground in close proximity. Some give warning of ground ahead of the aircraft (Enhanced GPWS), but most only look down not forwards.
FADEC - Full Authority Digital Engine Control. Each engine has one. Basically an advanced version of what's in most posh cars these days. It basically looks after and controls the engine and all it's parameters.
FCOM - Flight Crew Operating Manual. The Airbus acronym for the aircraft's technical manuals. There are 4 in the series - all cover different things.
The original question related to why the Number 1 (left-side) reverser (the part of the engine that provides reverse thrust for braking after landing) doesn't work when LGCIU 1 doesn't work. The answer is that for the reverse thrust to work, the FADEC (which controls reverse thrust for its individual engine) must receive a signal from LGCIU 1 that the left main landing gear is on the ground. This is to make sure that reverse thrust can never happen in the air - the aircraft would possibly crash if it did. However, when LGCIU 1 doesn't work, the FADEC on engine 1 doesn't get that signal and therefore will not allow reverse thrust on that engine because it doesn't know that the aircraft has landed. All about safety really.
Hope that helps and is not too long-winded!!!
Cheers
LGCIU - Landing Gear Control Interface Unit. The aircraft has 2 of these. These are the "brains" of the landing gear system. They give orders and information to bits of the areoplane that need it about the what the landing gear is doing. ie is it up/down/unlocked etc. Also they sequence the movement of the landing gear itself. Amongst other things!
GPWS - Ground Proximity Warning System. Every commercial aircraft has one and it does exactly what it says on the tin - warns the crew of ground in close proximity. Some give warning of ground ahead of the aircraft (Enhanced GPWS), but most only look down not forwards.
FADEC - Full Authority Digital Engine Control. Each engine has one. Basically an advanced version of what's in most posh cars these days. It basically looks after and controls the engine and all it's parameters.
FCOM - Flight Crew Operating Manual. The Airbus acronym for the aircraft's technical manuals. There are 4 in the series - all cover different things.
The original question related to why the Number 1 (left-side) reverser (the part of the engine that provides reverse thrust for braking after landing) doesn't work when LGCIU 1 doesn't work. The answer is that for the reverse thrust to work, the FADEC (which controls reverse thrust for its individual engine) must receive a signal from LGCIU 1 that the left main landing gear is on the ground. This is to make sure that reverse thrust can never happen in the air - the aircraft would possibly crash if it did. However, when LGCIU 1 doesn't work, the FADEC on engine 1 doesn't get that signal and therefore will not allow reverse thrust on that engine because it doesn't know that the aircraft has landed. All about safety really.
Hope that helps and is not too long-winded!!!
Cheers
Join Date: Jul 2002
Location: Hungary
Age: 39
Posts: 684
Likes: 0
Received 0 Likes
on
0 Posts
Fantastic reply and easy to understand. Much appreciated...I have been interested in aviation since 3, and ever since up to 18 and a half years old, I have read aviation, aircraft. Got PPL etc, but you'll always find me reading some ATPL syllabus level material, or aircraft specific material. That is why this interested me. I like to be intelligent you see 
No point living without knmowledge of some kind.
Smooth skies, thanks again...
Dan
No point living without knmowledge of some kind.Smooth skies, thanks again...
Dan
and it always helps for chatting up the ladies in the bar!...or is that boring them to tears in the bar...I always get that mxed up Join Date: Jul 2002
Location: Hungary
Age: 39
Posts: 684
Likes: 0
Received 0 Likes
on
0 Posts
I'm taken with an amazing girl, so you wont find me chatting up at the bar. I think its boring them to tears. I once got talkin about the approach into Heathrow when I saw a virgin 340, but I stopped after a couple seconds. Think I would be down the bar chatting up if I didnt stop 
Join Date: Jan 2001
Location: Sweden
Posts: 116
Likes: 0
Received 0 Likes
on
0 Posts
LGCIU1 failure does NOT render Reverser 1 inop. First of all the FADEC is not involved in the reverser depolyment, only in the power setting of the engine. The On-Side EIU(Engine interface unit) recieves the revers signal from the Thrust potentiometer, it then checks for groung signal, first from onside LGCIU, if that is missing it uses Off side plus Radio alt and/or Wheel speed if all these conditions are fullfilled then it checks for Revers confirmation signal from SEC(spoiler elevator computer)then it sends a revers deploy signal to the HMU, when it recieves revers deployed more than 90% it lets the FADEC increase thrust.
Join Date: Dec 1998
Location: UK
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
OK, well in that case, why does the FCOM on page 1.32.10 p14 say:
"FADEC :
A/c in flight (when either LGCIU output indicates flight) - Reverse inhibited
A/c on ground (when BOTH LGCIU outputs indicate ground) - Reverse available"
The way I read that is that BOTH outputs of the LGCIU have to see a ground condition for reverse not to be inhibited on that side, each LGCIU having 2 outputs.
It also says :
"The FADEC system performs the following functions:
Thrust reverser control - actuation of the blocker doors
- engine setting during reverser operation"
"FADEC, also called the EEC, is a digital control system that performs complete engine management"
FCOM 1.70.20 p1 and p4 refer.
Either way - you cannot get away from the fact that with an LGCIU inoperative - reverse IS lost on the that side. I know that because it says it in the FCOM, I've had it in the sim and on the aircraft - it DOES happen.
Cheers all
"FADEC :
A/c in flight (when either LGCIU output indicates flight) - Reverse inhibited
A/c on ground (when BOTH LGCIU outputs indicate ground) - Reverse available"
The way I read that is that BOTH outputs of the LGCIU have to see a ground condition for reverse not to be inhibited on that side, each LGCIU having 2 outputs.
It also says :
"The FADEC system performs the following functions:
Thrust reverser control - actuation of the blocker doors
- engine setting during reverser operation"
"FADEC, also called the EEC, is a digital control system that performs complete engine management"
FCOM 1.70.20 p1 and p4 refer.
Either way - you cannot get away from the fact that with an LGCIU inoperative - reverse IS lost on the that side. I know that because it says it in the FCOM, I've had it in the sim and on the aircraft - it DOES happen.
Cheers all
Join Date: Jan 2002
Location: West Country
Posts: 1,271
Likes: 0
Received 0 Likes
on
0 Posts
Airbus Operations Manual A320 IAE
Reverser Actuation Logic - 12-70-75-2
Deployment requires:
Before the deployment is completed, the FADEC sets reverse idle thrust on the engine that is having its thrust reversed.
Reverser Actuation Logic - 12-70-75-2
Deployment requires:
- One FADEC channel operating with its associated throttle reverse signal
- Right and left main gear compressed signals from the corresponding LGCIU's
- A Thrust Lever angle (TLA) reverse signal from at least one Spoiler Elevator Computer (SEC)
Before the deployment is completed, the FADEC sets reverse idle thrust on the engine that is having its thrust reversed.
Join Date: Jun 2001
Location: Over The Hills And Far Away
Posts: 676
Likes: 0
Received 0 Likes
on
0 Posts
Remember that FCOM means FLIGHT CREW Operating Manual.
What is written in those manuals are quite often lacking detailed information on how a system is designed and works.
If you want to know how to operate a system they are fine but if you want to know how a system works they are not.
I suspect that the Doc has access to the MM and WDM.
What is written in those manuals are quite often lacking detailed information on how a system is designed and works.
If you want to know how to operate a system they are fine but if you want to know how a system works they are not.
I suspect that the Doc has access to the MM and WDM.
Join Date: Dec 1998
Location: UK
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
I'm sure Airbus would be glad to hear that their manuals are so poor!!!!!
Look, at the end of the day you DO lose Reverser 1 when LGCIU 1 is inoperative - I've had it on the REAL AEROPLANE - it DOES happen!!!!!!!!!!!!!!!!!!
I'm sorry but I just can't accept that the Maintenance Manual and the FCOM would be different, which is effectively what you are saying! What the Doc has said is just plain wrong according to my A320 FCOMs. Maybe the MM is more detailed yes, but different - no way!!!!!!!!!!!!!!!
Look, at the end of the day you DO lose Reverser 1 when LGCIU 1 is inoperative - I've had it on the REAL AEROPLANE - it DOES happen!!!!!!!!!!!!!!!!!!
I'm sorry but I just can't accept that the Maintenance Manual and the FCOM would be different, which is effectively what you are saying! What the Doc has said is just plain wrong according to my A320 FCOMs. Maybe the MM is more detailed yes, but different - no way!!!!!!!!!!!!!!!
Last edited by SLT; 13th Jun 2003 at 02:44.
Join Date: Jun 2001
Location: Over The Hills And Far Away
Posts: 676
Likes: 0
Received 0 Likes
on
0 Posts
What I am saying is that your manuals are exactly what it says on the cover, Flight Crew OPERATING manuals.
With regards to the technical description of the aeroplane they are full of generalizations and simplifications.
It is not uncommon to see only the major components of a system described and assigned functions, which in reality are carried out by one of the many other components in the system that are not included in the description.
All in the name of simplicity.
And not only in that respect is the MM different fom the FCOM, it will also differ in operating techniques and limitations.
To give you an idea of how simplified they are, I can tell you that I have taken the computerized test in a couple of the systems and passed. Without any training or knowledge of the A320 I passed tests which I assume are based on information coming from the FCOM. I might just have been lucky, but I doubt it.
With regards to the technical description of the aeroplane they are full of generalizations and simplifications.
It is not uncommon to see only the major components of a system described and assigned functions, which in reality are carried out by one of the many other components in the system that are not included in the description.
All in the name of simplicity.
And not only in that respect is the MM different fom the FCOM, it will also differ in operating techniques and limitations.
To give you an idea of how simplified they are, I can tell you that I have taken the computerized test in a couple of the systems and passed. Without any training or knowledge of the A320 I passed tests which I assume are based on information coming from the FCOM. I might just have been lucky, but I doubt it.
Join Date: Feb 2002
Location: The Sandpit
Posts: 555
Likes: 0
Received 0 Likes
on
0 Posts
EIU/LGCIU
Well this one got me going! Had to have a look at the manuals to check!
SLT is quite right LGCIU #1 fail will cause T/R #1 fail. I have had it too, as a line defect (I am an engineer). And the simple reason is that the onside LGCIU controls the reverser actuation logic.
The complicated answer is a bit more involved (aren't they always
)
Doc is I am afraid wrong. He is also right
. Let me explain
The onside Engine Interface Unit (EIU) provides actuation logic for the T/R based on Throttle Lever Angle (TLA) less than 3 degs (This info comes from the SEC's) and a/c on the ground (from the onside LGCIU) If the conditions are met then an inhibit relay is activated. This relay then allows the FADEC ECU to control the operation of the reverser itself, provided that the T/R isolation valve (hydraulic valve) is open (this valve opens when SEC's 'see' reverse commanded and a/c on ground or less than 10 foot RA)
However, the be all and end all is that a failure of a LGCIU will result in loss of the onside reverser.
Hope this helps.
SLT is quite right LGCIU #1 fail will cause T/R #1 fail. I have had it too, as a line defect (I am an engineer). And the simple reason is that the onside LGCIU controls the reverser actuation logic.
The complicated answer is a bit more involved (aren't they always
)Doc is I am afraid wrong. He is also right
. Let me explainThe onside Engine Interface Unit (EIU) provides actuation logic for the T/R based on Throttle Lever Angle (TLA) less than 3 degs (This info comes from the SEC's) and a/c on the ground (from the onside LGCIU) If the conditions are met then an inhibit relay is activated. This relay then allows the FADEC ECU to control the operation of the reverser itself, provided that the T/R isolation valve (hydraulic valve) is open (this valve opens when SEC's 'see' reverse commanded and a/c on ground or less than 10 foot RA)
However, the be all and end all is that a failure of a LGCIU will result in loss of the onside reverser.
Hope this helps.
Join Date: Jan 2001
Location: Sweden
Posts: 116
Likes: 0
Received 0 Likes
on
0 Posts
Hi Mono,
I just had a look at my traing manuals and then the AMM, and guess what, we are both right.
On the CFM powered A/C WITHOUT SB 320/78-12b incorborated it is true that on side LGCIU failure will cause onside Reverser to be locked out, post mod, the command LGCIU will give the GND logic to both EIU's.
You are right about the actuation logic, it has been a while since I was working with that sys in depht and was going by my teflon memory(nothing sticks)
Brgds
Doc
I just had a look at my traing manuals and then the AMM, and guess what, we are both right.
On the CFM powered A/C WITHOUT SB 320/78-12b incorborated it is true that on side LGCIU failure will cause onside Reverser to be locked out, post mod, the command LGCIU will give the GND logic to both EIU's.
You are right about the actuation logic, it has been a while since I was working with that sys in depht and was going by my teflon memory(nothing sticks)
Brgds
Doc
Join Date: Jul 2002
Location: Hungary
Age: 39
Posts: 684
Likes: 0
Received 0 Likes
on
0 Posts
Could you translate that quote from the A320 AMM into English by any chance?
Thanks
Dan
(im following this post you see. I am interested in all the complicated stuff if thats ok)...
Thanks
Dan
(im following this post you see. I am interested in all the complicated stuff if thats ok)...