Boeing Undercarriage Retraction
Thread Starter
Join Date: Mar 2002
Location: Mid-central South of England
Posts: 201
Likes: 0
Received 0 Likes
on
0 Posts
Boeing Undercarriage Retraction
Mrs Flo was recently on a long haul flight on a 744 and commented that the noise and vibration from the undercarriage (she was back at doors 4) during retraction, was much greater than normal ( she has been 777and 747 CC for going on 25 years so has heard it sufficiently regularly to comment I believe). She had commented on it during the first sector but noticed it again on the second, while of course it may well be nothing she asked me about it and I'm not sure it's the same as the bus.
Question is, does auto brake activate after lift off and stop the main gear from spinning and is it linked to the auto brake used during a rejected take off. Would tyre wear and wheel balance cause vibration and is there any indications of tyre pressure and or vibration on the flight deck? Finally do the flight crew have to do anything to initiate wheel braking during retraction?
Many thanks
A-F....
Question is, does auto brake activate after lift off and stop the main gear from spinning and is it linked to the auto brake used during a rejected take off. Would tyre wear and wheel balance cause vibration and is there any indications of tyre pressure and or vibration on the flight deck? Finally do the flight crew have to do anything to initiate wheel braking during retraction?
Many thanks
A-F....
Join Date: Aug 2007
Location: The Netherlands
Age: 67
Posts: 288
Likes: 0
Received 0 Likes
on
0 Posts
Spelling
...the breaking after takeoff is automatic....
After which the picking up of the pieces is a manual affair ...
Pre-retraction wheel braking is an automatic function.
Now IF an aircraft is dispatched with a wheelbrake deactivated, that one wheel could be spinning for a while, possibly with associated noise. It is also possible that the procedure then describes to wait a certain amount of time with retraction to let the spinning reduce to an acceptable level before retraction. The period of flight with gear down would also be noisier than usual after take-off.
After which the picking up of the pieces is a manual affair ...
Pre-retraction wheel braking is an automatic function.
Now IF an aircraft is dispatched with a wheelbrake deactivated, that one wheel could be spinning for a while, possibly with associated noise. It is also possible that the procedure then describes to wait a certain amount of time with retraction to let the spinning reduce to an acceptable level before retraction. The period of flight with gear down would also be noisier than usual after take-off.
Per the MEL if the brakes are deactivated by just capping the line and not using the brake deactivation tool you leave the gear down two minutes to allow the wheels to spin down.
Thread Starter
Join Date: Mar 2002
Location: Mid-central South of England
Posts: 201
Likes: 0
Received 0 Likes
on
0 Posts
Thanks so far....
Thanks for the expansion to the first answer......Pretty much as I expected. Think it might be pertinent to advice the CSD/CSL if was an MEL item as they may well, as in this case, wonder what the difference or problem is. Of course it also may not be this, I've read of RTOs due to nose and main gear shimmy all caused by wear on the shoulder of the tyres and even tyre pressures....
Axel
Axel
Join Date: Feb 2004
Location: Australia
Posts: 1,307
Likes: 0
Received 0 Likes
on
0 Posts
During retraction, some of the hydraulic pressure used for retraction is ported to valves which activate the brake system to de-spin/brake the wheels. The 747-400 "autobrake" system per se, is not used to carry out de-spin.
It's all done with mechanical valves. I suppose there could be faulty components, leaks, etc. It wouldn't hurt to tell someone about the unusual noise, especially if the person is a frequent flyer like Mrs-Flo.
Did the noise continue well after retraction?
It's all done with mechanical valves. I suppose there could be faulty components, leaks, etc. It wouldn't hurt to tell someone about the unusual noise, especially if the person is a frequent flyer like Mrs-Flo.
Did the noise continue well after retraction?
Thread Starter
Join Date: Mar 2002
Location: Mid-central South of England
Posts: 201
Likes: 0
Received 0 Likes
on
0 Posts
Apparently....yes.
On 2 occasions, same route legs 1 and 2 but different aircraft. The second sector yes, the wheels seemed to continued to run for a while after gear retraction, from her point of view, and after the main gear doors had closed. She had mentioned it on the first leg with little or no response and certainly no follow up. Second time reported it to the CSD but it went no further and the flight deck said it seemed normal to them so not to worry about it. It was as much my trying to explain the system and how it worked on the bus I now fly and the previous type (albeit a first generation classic that had a big wood and rubber block rubbing strip for the nose gear) and wondering how the 74/77 systems by Boeing worked in comparison. Thanks
Last edited by Axel-Flo; 16th Jul 2015 at 01:03.
Join Date: Feb 2004
Location: Australia
Posts: 1,307
Likes: 0
Received 0 Likes
on
0 Posts
The 747-400 nosewheel de-spin is the old style, too.... A fire-resistant pad attached to spring metal which contacts the tyres. In the forward zone, it sometimes sounds like a circular saw cutting through timber (quite a surprise to first-timers).
Join Date: Jun 2010
Location: Brisbane, Australia
Posts: 304
Likes: 0
Received 0 Likes
on
0 Posts
If the vibration was THAT noticeable back at door 4 on the '74, the problem of auto de-spin not working was most probably affecting the body gear, not the wing gear, which of course, you can't see!
Body gear wheel balance/de-spin problems are significantly more evident in the way of vibrations felt in the pax cabin.
Body gear wheel balance/de-spin problems are significantly more evident in the way of vibrations felt in the pax cabin.
Thread Starter
Join Date: Mar 2002
Location: Mid-central South of England
Posts: 201
Likes: 0
Received 0 Likes
on
0 Posts
Spin up
Following on from these answers, and thank you for them all I have passed them on, was/is there any manufacturers that have a spin up system other than, of course, the moment of rubber and runway interface?
Join Date: Feb 2004
Location: Australia
Posts: 1,307
Likes: 0
Received 0 Likes
on
0 Posts
was/is there any manufacturers that have a spin up system other than, of course, the moment of rubber and runway interface?
Join Date: Aug 2005
Location: fairly close to the colonial capitol
Age: 55
Posts: 1,693
Likes: 0
Received 0 Likes
on
0 Posts
was/is there any manufacturers that have a spin up system other than, of course, the moment of rubber and runway interface?
Other than that, Mr. Flo, no large aircraft I know of have such a thing, although it was something fitted to Learjets for use on unimproved runways (gravel).
NASA or the USAF, I can't remember which, studied tire wear on large aircraft and discovered most tread wear is due to cornering forces and not smoky touchdowns.
Join Date: Apr 2008
Location: nowhere
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
I flew as a passenger on a straight wing Citation II a few years back in order to be positioned to pick up an aircraft. This aircraft would occasionally land on gravel runways. The crew told us that the nosewheel had an auto-spinup feature in order to reduce the likelihood of gravel being picked up and hitting the belly. This is part of the optional gravel kit installation.
A look at the nosewheel showed that there did appear to be some sort of add-on to the axel(perhaps axle) portion of the wheel.
There is mention about it in this link.
1977 | 1244 | Flight Archive
A look at the nosewheel showed that there did appear to be some sort of add-on to the axel(perhaps axle) portion of the wheel.
There is mention about it in this link.
1977 | 1244 | Flight Archive
Join Date: Sep 2010
Location: earth
Posts: 1,341
Likes: 0
Received 0 Likes
on
0 Posts
I am pretty sure the process is very common amongst jet aircraft. I can speak for the DC10/MD11 aircraft as I have performed this check during heavy MX visits. Hydraulic sequence logic ports roughly 400 PSI to the brakes from the time the retract actuator is commanded until the gear is up.
