How many screws does it take to attach a DC3 wing?
Thread Starter
Join Date: Nov 2008
Location: The New Forest, UK
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
How many screws does it take to attach a DC3 wing?
Many, many small ones!
This has always amazed me, don't know if it is a common method across all Douglas piston fleet.
It seems to work as these wings don't snap the screws and break off!
The wing attachment of the 747 and A380 keep me awake at night...
This has always amazed me, don't know if it is a common method across all Douglas piston fleet.
It seems to work as these wings don't snap the screws and break off!
The wing attachment of the 747 and A380 keep me awake at night...
Last edited by b377; 19th Feb 2009 at 12:56.
Almost right - 328 per side (102 x AN4-7A & 226 x AN410A bolts to be exact).
The bolts are torqued once on wing installation and then again after the first flight.
A real arm-acher!
The bolts are torqued once on wing installation and then again after the first flight.
A real arm-acher!
Join Date: Jun 2004
Location: Australia
Posts: 1,843
Likes: 0
Received 0 Likes
on
0 Posts
Those very un-aerodynamic rows of bolts at the wing butt joints used to be covered with a neat cover strip in times of olds.
Problem was, when they finally corroded and failed, they would quietly slip unseen overboard beneath the cover strip. This would not be visible on a regular visual inspection.
The cover strips were finally removed after a fatal wing separation after too many bolts had disappeared, leaving too few to carry the loads.
Regards,
Old Smokey
Problem was, when they finally corroded and failed, they would quietly slip unseen overboard beneath the cover strip. This would not be visible on a regular visual inspection.
The cover strips were finally removed after a fatal wing separation after too many bolts had disappeared, leaving too few to carry the loads.
Regards,
Old Smokey
Psychophysiological entity
While a young DC3 first officer, I recall being told that the spar was just two end-sections, held abutted together by these nuts and bolts.
I've mentioned before on Pprune about my regrets of not buying a little book of DC3 'mishaps'. Rather an understatement.
One picture was of a missing port wing...not far out from the bolts. It had somehow got back after hitting a mountain. The comment: "I bet this got their attention."
Anyone know about this book? It was on sale in a flying school near Austin some 15 years ago.
I've mentioned before on Pprune about my regrets of not buying a little book of DC3 'mishaps'. Rather an understatement.
One picture was of a missing port wing...not far out from the bolts. It had somehow got back after hitting a mountain. The comment: "I bet this got their attention."
Anyone know about this book? It was on sale in a flying school near Austin some 15 years ago.
Aviator Extraordinaire
Join Date: May 2000
Location: Oklahoma City, Oklahoma USA
Age: 76
Posts: 2,394
Likes: 0
Received 0 Likes
on
0 Posts
LR, can't speak as to the book, however, have you seen this website?
The DC-3 Hangar on douglasdc3.com DC3 C47 C-47
A lot of DC-3 information there.
Cheers.
The DC-3 Hangar on douglasdc3.com DC3 C47 C-47
A lot of DC-3 information there.
Cheers.
While a young DC3 first officer, I recall being told that the spar was just two end-sections, held abutted together by these nuts and bolts.
Well, there's a little bit more to it. There are three spars in both the outer wing and centre section. Each one, top and bottom has a butt plate at the end of the caps and there are compression angles and waffle plates between the spars as well as a diaphragm to even out the load. Then you have some substantial doublers under the wing attachment angles themselves. The wings are held on by those 1/4" bolts around the chord, no others.
I seem to remember Northropp having something to do with the DC3 multi-cell wing design.
Well, there's a little bit more to it. There are three spars in both the outer wing and centre section. Each one, top and bottom has a butt plate at the end of the caps and there are compression angles and waffle plates between the spars as well as a diaphragm to even out the load. Then you have some substantial doublers under the wing attachment angles themselves. The wings are held on by those 1/4" bolts around the chord, no others.
I seem to remember Northropp having something to do with the DC3 multi-cell wing design.
Psychophysiological entity
Well, there's a little bit more to it.
con, that site is certainly improved by turning off Adblock
One of One when we had proper airyplanes.
Thread Starter
Join Date: Nov 2008
Location: The New Forest, UK
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
LR One of One when we had proper airyplanes.
those rolling hills behind the Dakota ? Date?
What was that cable for, ground power? No APU in the old bird.
I can just smell that Av Gas - better than Chanel for you guys !
BITM
Look they are Engineers. We dont call them screws anymore.....
Oh, so you called them screws once? What were pilots called then?
Psychophysiological entity
I'm not sure if it was Aberdeen or Edinburgh About 70-71
Sun-bronzed Sky gods of course.
In reality, it would probably be better not to ask.
What were pilots called then?
Sun-bronzed Sky gods of course.
In reality, it would probably be better not to ask.
Join Date: Dec 2014
Location: 40nm east of BLL
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
here's a video of the job;
Boeing Images - Douglas DC-3 Assembly Line, 1930s
there is aparantly no overlay of spars in the connection-line and no inner spanning of a possible spar-connection.
But the timeconsuming spanning of the row of bolts are to see!
Boeing Images - Douglas DC-3 Assembly Line, 1930s
there is aparantly no overlay of spars in the connection-line and no inner spanning of a possible spar-connection.
But the timeconsuming spanning of the row of bolts are to see!