Go Back  PPRuNe Forums > Misc. Forums > Computer/Internet Issues & Troubleshooting
Reload this Page >

A Shot in the dark...Cambridge Soundworks

Computer/Internet Issues & Troubleshooting Anyone with questions about the terribly complex world of computers or the internet should try here. NOT FOR REPORTING ISSUES WITH PPRuNe FORUMS! Please use the subforum "PPRuNe Problems or Queries."

A Shot in the dark...Cambridge Soundworks

Old 29th Dec 2009, 22:45
  #1 (permalink)  
Thread Starter
 
Join Date: Mar 2006
Location: Chez Sprog
Posts: 493
Likes: 0
Received 0 Likes on 0 Posts
A Shot in the dark...Cambridge Soundworks

I have a dearly loved Cambridge DT2200 5.1 speaker system. These haven't been made for 10 years or so, but are still superior in many ways to todays crop of pc speaker systems imho.

The pot on the volume control is wearing out, giving me fluctuations in volume from time to time, so I need to replace it. Needless to say it's not available anymore, so if by any slim chance, anyone has one of these knocking about in a box somewhere, unused and unloved, Sprogget towers has ready cash waiting for you.

How about that? a reverse ad on pprune. You could save my earholes.

Last edited by Sprogget; 29th Dec 2009 at 23:02.
Sprogget is offline  
Old 30th Dec 2009, 03:35
  #2 (permalink)  
Psychophysiological entity
 
Join Date: Jun 2001
Location: Tweet Rob_Benham Famous author. Well, slightly famous.
Age: 84
Posts: 3,263
Received 24 Likes on 15 Posts
Have you tried cleaning fluid into the pot?

Servisol Aerosols

Top left. Gosh, that brings back some memories.


Failing that, most pots are just bog-standard items. One of the main things is whether or not its Linear or Log or Log Log, etc., resistive and physical size is obvious, and remember, cutting the shaft must be done by clamping the bit that's coming off, in the vice. Not holding by 'tother end.
Loose rivets is offline  
Old 30th Dec 2009, 12:44
  #3 (permalink)  
 
Join Date: Jul 2006
Location: Up yer nose, again.
Age: 67
Posts: 1,228
Received 12 Likes on 10 Posts
physical size is obvious, and remember, cutting the shaft must be done by clamping the bit that's coming off,


Sounds very painful
Peter Fanelli is offline  
Old 30th Dec 2009, 17:04
  #4 (permalink)  
Psychophysiological entity
 
Join Date: Jun 2001
Location: Tweet Rob_Benham Famous author. Well, slightly famous.
Age: 84
Posts: 3,263
Received 24 Likes on 15 Posts
That made I larf that did . . . until I remembered the bit about the vice.
Loose rivets is offline  
Old 30th Dec 2009, 17:40
  #5 (permalink)  
More bang for your buck
 
Join Date: Nov 2005
Location: land of the clanger
Age: 81
Posts: 3,512
Likes: 0
Received 0 Likes on 0 Posts
The (metal)cut off bits make good replacement fuses for 13amp plugs
green granite is offline  
Old 31st Dec 2009, 00:21
  #6 (permalink)  
Hippopotomonstrosesquipidelian title
 
Join Date: Oct 2006
Location: is everything
Posts: 1,826
Likes: 0
Received 0 Likes on 0 Posts
If you just want to replace the pot, it's probably a B50k, around 2 euros. Google would appear to be your friend, there are circuit diagrams and parts lists out there.
Bushfiva is offline  
Old 31st Dec 2009, 07:16
  #7 (permalink)  
 
Join Date: Jan 2006
Location: Dorking
Posts: 491
Received 0 Likes on 0 Posts
With the power off (to save your ears) wind the volume knob up and down lots and lots of times.

This usually grinds the carbon dust up enough to clear the problem.

Free.

Last edited by boguing; 31st Dec 2009 at 17:30.
boguing is offline  
Old 31st Dec 2009, 08:19
  #8 (permalink)  
Thread Starter
 
Join Date: Mar 2006
Location: Chez Sprog
Posts: 493
Likes: 0
Received 0 Likes on 0 Posts
The pot is a B50k and I'm wise enough to know that I ain't going anywhere near a soldering iron. I've destroyed more expensive kit than this in the past waving a stick of hot metal around.

Boguing, I did what you suggest and so far so good. My trouble is that I have set up this system such that there is a speaker in each corner of the room with the wiring running around the top of the picture rails and chased in to the wall, so it is immovable.

New systems tend to have the controls fixed in to one of the speakers such that I would have to stretch up to the ceiling to turn the things on and off or get into some heavy splicing/re-wiring to make the thing work. A non starter for me.
Sprogget is offline  
Old 31st Dec 2009, 09:09
  #9 (permalink)  
 
Join Date: May 2001
Posts: 10,815
Likes: 0
Received 0 Likes on 0 Posts
The pot is a B50k and I'm wise enough to know that I ain't going anywhere near a soldering iron. I've destroyed more expensive kit than this in the past waving a stick of hot metal around.
Avionics engineer by any chance?
mad_jock is offline  
Old 31st Dec 2009, 10:20
  #10 (permalink)  
Thread Starter
 
Join Date: Mar 2006
Location: Chez Sprog
Posts: 493
Likes: 0
Received 0 Likes on 0 Posts
Nope, but I see what you mean...
Sprogget is offline  
Old 31st Dec 2009, 10:45
  #11 (permalink)  
Spoon PPRuNerist & Mad Inistrator
 
Join Date: Sep 2003
Location: Twickenham, home of rugby
Posts: 7,374
Received 234 Likes on 152 Posts
I had a Cambridge Soundworks DT3500 system, but the head unit failed.

Very, very good it was too, up 'til then.

Like you, the corner speakers were fixed in awkward places, so I bought a Creative something 5.1 system, and just replaced the head unit and unpowered sub with the new powered sub and cabled all the other existing speakers back to that - fortunately there was enough slack in all the cables to do so.

It isn't as good as the DT3500, though.

SD
Saab Dastard is offline  
Old 31st Dec 2009, 10:54
  #12 (permalink)  
 
Join Date: Mar 2001
Location: North Cornwall
Age: 73
Posts: 428
Likes: 0
Received 0 Likes on 0 Posts
Sprogget
I found a guy in the North-west who is a dab hand with a soldering iron. He solved the dry joints problem of my much loved Sony ICF2001D. He specialises in repairing older electronic kit and charges are very reasonable. I will PM his contact details if that helps.
srobarts is offline  
Old 31st Dec 2009, 12:24
  #13 (permalink)  
Thread Starter
 
Join Date: Mar 2006
Location: Chez Sprog
Posts: 493
Likes: 0
Received 0 Likes on 0 Posts
Thanks Mr Sr, but if i send it away to the far northwest. I'll be soundless for a week or more!

I've been reprieved for the time being by jiggling the pot and giving it a clean. As Saab says, I've looked into the idea of swapping the subwoofer out as speakers are speakers, but looking so far at Altec and Logitech stuff, the controls are wired into one of the satellite speakers, so it would require surgery to get them working with my particular setup.

It worries me that what ever follows won't be as good as what I have now, they really are a very good system.
Sprogget is offline  
Old 31st Dec 2009, 13:27
  #14 (permalink)  
 
Join Date: Jan 2006
Location: Dorking
Posts: 491
Received 0 Likes on 0 Posts
Stop worrying - the pot will be fine for ages. I've been impressing people with this trick since I was about 11 (a looong time)!
boguing is offline  
Old 31st Dec 2009, 15:58
  #15 (permalink)  
 
Join Date: Dec 2002
Location: MerryEngland
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
This is a job for International Potentiometer Repair Man . When he has done yours, my surround sound amplifier needs his skills.
Thinks is this pot failure; part of a subversive act by others who don't want their vocal volume to be exceeded?
LordGrumpy is offline  
Old 31st Dec 2009, 17:56
  #16 (permalink)  
Psychophysiological entity
 
Join Date: Jun 2001
Location: Tweet Rob_Benham Famous author. Well, slightly famous.
Age: 84
Posts: 3,263
Received 24 Likes on 15 Posts
This is bringing back some memories. The old soft 'lead' pencil trick. Pry open the pot - often done in situ - and scribe many lines on the carbon track with the graphite.

On this forum, on which I'm Top Anode, they are full of tricks of the trade. They are mostly from my era, where we made old kit work from war-surplus stuff.

UK Vintage Radio Repair and Restoration Discussion Forum - Powered by vBulletin

Young people of today don't know how to fix things. My old science master's homemade t/v was 2 1/2" green screen. And then there was the bloke that breathed life into his tires every Sunday morning with Bandages and Bostic . . .



God, old people can really be boring.
Loose rivets is offline  
Old 24th Dec 2012, 13:45
  #17 (permalink)  
 
Join Date: Dec 2012
Location: UK
Age: 75
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
Hello Sprogget I hope you're still around now & still on here.

I've searched the net for pretty much the same problem as you other than mine is the balance control thats playing up. It just goes round & round infinitely but with no difference to the sound.

Did you get your problem sorted & if so how please?
Marie B is offline  
Old 25th Dec 2012, 14:10
  #18 (permalink)  
 
Join Date: Jan 2012
Location: .
Posts: 2,173
Likes: 0
Received 0 Likes on 0 Posts
Someone with a similar problem - and some ideas - here
Ancient long shot in the dark - Overclockers UK Forums

or is that you?
Milo Minderbinder is offline  
Old 25th Dec 2012, 17:40
  #19 (permalink)  
 
tony draper's Avatar
 
Join Date: May 2001
Location: Newcastle/UK
Posts: 1,476
Likes: 0
Received 0 Likes on 0 Posts
Had the same prob with the same kit,the VC was on a flat ribbon cable and got beyond help,took it apart squirted it with switch clean did the usual things but eventually got fed up and binned it,still it had lasted a long time.
tony draper is offline  
Old 26th Dec 2012, 10:48
  #20 (permalink)  

Official PPRuNe Chaplain
 
Join Date: Apr 2001
Location: Witnesham, Suffolk
Age: 80
Posts: 3,498
Likes: 0
Received 0 Likes on 0 Posts
Oh, the frustration of realising that the old eyes can't focus properly at soldering distance.

Took me several minutes to change out the pot that had gone noisy. Where I used to be able to hold the iron in one hand and the solder sucker in the other while balancing the device on my knee, now it's bench, "helping hands" and patience.
Keef is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.