PDA

View Full Version : LVP:effect of failed or downgraded eqpt. on approaches


Nitin3286
12th Jan 2016, 02:35
hi,what is the effect of standby power for approach lights for CAT1 & CAT2 approache minima?

whitelabel
13th Jan 2016, 00:25
For Cat 1/2 no effect but Cat 3 not allowed

despegue
13th Jan 2016, 00:49
Depends on the Company LVP , but in general, Approach Lights are not required to work for a Cat3 approach. Reason of course is that on a Cat 3, you will not even see any approach lights as DA is for a Cat 3A over the threshold.

Approach lights ARE required for Cat2 approaches, fully operational.

Gryphon
13th Jan 2016, 09:33
EU-OPS: unserviceability of standby power for app lights has no effect on landing minima.

FlightDetent
13th Jan 2016, 13:35
Makes sense. Lights go off, standby power source does not kick in, you go around if visual reference lost. Unlucky, but safe enough. No need nor benefit in mandating a minima increase.

16024
13th Jan 2016, 18:32
Light go off, you go around

Not quite. Remember this is about the standby power system, which is listed in the "Failed or Downgraded Equipment" table somewhere in your part A. Also in there will be a NALS minima table (No approach lights) which more or less tells you to use increased Cat1 minima. No need to go around if you can see it.

despegue
13th Jan 2016, 18:39
16024,

Not in ours it doesn't.
If not mentioned on the charts, then normal cat1 minima apply for approach lights inop or on sby. Don't restrict yourselves when not necessary...

As I said before, if the RWY is Cat3 equipped, you can do a CAT3 as no approach light system is necessary for such approach.

FlightDetent
13th Jan 2016, 19:51
16024:
EASA Acceptable Means of Compliance (AMC) and Guidance Material (GM) to Part-SPA

AMC7 SPA.LVO.100 Low visibility operations
EFFECT ON LANDING MINIMA OF TEMPORARILY FAILED OR DOWNGRADED EQUIPMENT
Standby power for approach lights: No effect

My mind was focused on the LVP part, yours probably on the CAT I, hence the discord. Take care. :)

B737900er
14th Jan 2016, 16:33
I believe there is some confusion with
Standby power Inop for approach lights and Approach lights inop.

16024
15th Jan 2016, 14:15
Flight Detent:
I agree 100% with your edit of post #5!

Despegue:
normal cat1 minima apply for approach lights inop

Here's the link:

http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=OJ:L:2008:254:0001:0238:EN:PDF

On page 75 there's a table, and for NALS your cat1 DH remains at 200' but your required rvr is 1200m. I agree that it is a bit confusing unless we are clear whether we are talking about standby power failure or complete loss of lighting.

BANANASBANANAS
15th Jan 2016, 14:34
The question was re the effect of unserviceable standby power for Cat 1 and Cat 2 Procedures wasn't it?

Using EASA regs the answer is simple and as follows;

Cat 3 and Cat 2. No effect.

Cat 2 OTS and CAT 1. Minima as for NALS.

OR, Did the OP mean having to operate using SBY Power for the ALS?

In which case;

Cat 3B No DH. No Effect

Cat 3B with DH and Cat 3A. Not allowed for DH above 50 feet.

Cat 2. Not Allowed

Cat 2 OTS and Cat 1. Minima as for NALS